Power generation characteristics of a sandwich‐type self‐heating thermoelectric generator with spatially varying embedded heat source

Power generation characteristics of a sandwich‐type thermoelectric generator in which the heat source is embedded into thermoelectric elements are investigated. Our previous work on a similar concept only considered a uniform heat source distribution inside thermoelectric elements. In this work, the effect of the spatial distribution of a heat source is examined. In particular, the effect of the concentration of heat source near the one end, that is, the hot end, is intensively studied as a potential means of improving the efficiency of the device. Although the effects of heat source concentration in impractical cases without heat transfer limitations on the cold side remain ambiguous, it become clear that heat source concentration indeed has positive effects in more realistic cases with finite heat transfer coefficients imposed on the cold side. Because of the relatively low efficiency of typical thermoelectric generation, a significant amount of heat must be dissipated from the cold end of the thermoelectric element. Greater heat source concentration near the hot end leads to more effective utilization of available heat source, reduces the amount of heat rejected at the cold end, and lowers the hot end temperature of the thermoelectric element. Overall, it is suggested that heat source concentration can be used as a method to achieve more efficient operation and better structural integrity of the system. Copyright © 2015 John Wiley & Sons, Ltd.     

Graphene Quantum Sheet Catalyzed Silicon Photocathode for Selective CO2 Conversion to CO

The reduction of carbon dioxide (CO₂) into chemical feedstock is drawing increasing attention as a prominent method of recycling atmospheric CO₂. Although many studies have been devoted in designing an efficient catalyst for CO₂ conversion with noble metals, low selectivity and high energy input still remain major hurdles. One possible solution is to use the combination of an earth‐abundant electrocatalyst with a photoelectrode powered by solar energy. Herein, for the first time, a p‐type silicon nanowire with nitrogen‐doped graphene quantum sheets (N‐GQSs) as heterogeneous electrocatalyst for selective CO production is demonstrated. The photoreduction of CO₂ into CO is achieved at a potential of ?1.53 V versus Ag/Ag⁺, providing 0.15 mA cm^?2 of current density, which is 130 mV higher than that of a p‐type Si nanowire decorated with well‐known Cu catalyst. The faradaic efficiency for CO is 95%, demonstrating significantly improved selectivity compared with that of bare planar Si. The density functional theory (DFT) calculations are performed, which suggest that pyridinic N acts as the active site and band alignment can be achieved for N‐GQSs larger than 3 nm. The demonstrated high efficiency of the catalytic system provides new insights for the development of nonprecious, environmentally benign CO₂ utilization.     

Digital predistorter using multiple lookup tables

A new digital predistorter is proposed that copes with the variation of power amplifier characteristics faster than the adaptation rate of the predistorter by using multiple lookup tables. Experimental results derived from a prototype show that the proposed predistorter can suppress the adjacent channel interference up to 12 dB compared to the conventional predistorter with a single lookup table.     

Progressive NO2 Sensors with Rapid Alarm and Persistent Memory-Type Responses for Wide-Range Sensing Using Antimony Triselenide Nanoflakes

Antimony triselenide (Sb₂Se₃) nanoflake-based nitrogen dioxide (NO₂) sensors exhibit a progressive bifunctional gas-sensing performance, with a rapid alarm for hazardous highly concentrated gases, and an advanced memory-type function for low-concentration (<1 ppm) monitoring repeated under potentially fatal exposure. Rectangular and cuboid shaped Sb₂Se₃ nanoflakes, comprising van der Waals planes with large surface areas and covalent bond planes with small areas, can rapidly detect a wide range of NO₂ gas concentrations from 0.1 to 100 ppm. These Sb₂Se₃ nanoflakes are found to be suitable for physisorption-based gas sensing owing to their anisotropic quasi-2D crystal structure with extremely enlarged van der Waals planes, where they are humidity-insensitive and consequently exhibit an extremely stable baseline current. The Sb₂Se₃ nanoflake sensor exhibits a room-temperature/low-voltage operation, which is noticeable owing to its low energy consumption and rapid response even under a NO₂ gas flow of only 1 ppm. As a result, the Sb₂Se₃ nanoflake sensor is suitable for the development of a rapid alarm system. Furthermore, the persistent gas-sensing conductivity of the sensor with a slow decaying current can enable the development of a progressive memory-type sensor that retains the previous signal under irregular gas injection at low concentrations.     

Acoustooptic Tunable Gap-Type Bandpass Filter With a Broad Stopband

We demonstrate a novel all-fiber gap-type tunable bandpass filter configuration that consists of a broadband hollow optical fiber (HOF) acoustooptic tunable filter (AOTF) concatenated with a narrowband single-mode fiber (SMF)-AOTF. Owing to the unique mode coupling properties of HOF-AOTF and SMF-AOTF, a narrow passband channel of a full-width at half-maximum (FWHM) of ~4 nm could be formed in a broad stopband platform of a 90-nm FWHM successfully. In this scheme, the center wavelength and rejection efficiency of both passband and stopband were found to be flexibly tunable by adjusting the frequency and the voltage of radio-frequency signals applied to individual acoustic transducers.     

Low-Loss Polymer-Based Long-Range Surface Plasmon-Polariton Waveguide

To improve the propagation loss of polymer-based long-range surface-plasmon-polariton (LR-SPP) waveguide devices at the telecom wavelength range, low-loss LR-SPP waveguides were fabricated in an ultraviolet-curable acrylate polymer with a low refractive index and absorption loss. A propagation loss of 1.72 dB/cm at a wavelength of 1.55 mum was achieved with a 14-nm-thick and 3-mum-wide metal stripe.     

All-Optical Data Vortex Node Using an MZI-SOA Switch Array

We propose and demonstrate a new structure of a Data Vortex switch node for all-optical routing of wavelength-division-multiplexing (WDM) 10-Gb/s optical packets. The proposed node consists of two Mach-Zehnder interferometers with integrated semiconductor optical amplifier: an optical and gate and a high-speed optical switch. In the experiment, WDM 10-Gb/s data packets are successfully routed with 1-dB power penalty at a bit-error rate of 10^-9.     

n+/p+ Gate Bulk FinFETs With Locally Separated Channel Structure for Sub-50-nm DRAM Cell Transistors

We proposed a new p⁺/n⁺ poly-Si gate bulk fin-type field-effect transistor that has two channel fins separated locally by a shallow trench filled with oxide or p⁺ polygate. Key device characteristics were investigated by changing the n⁺ poly-Si gate length La, the material filling the trench, and the width and length of the trench at a given gate length L_g. It was shown that the trench filled with p⁺ poly-Si gate should not be contacted with the source/drain diffusion region to achieve an excellent I_on/I_off (> 1010) that is suitable for sub-50-nm dynamic random access memory cell transistors. Based on the aforementioned device structure, we designed reasonable Ls/Lg and channel fin width W_cfin at given L_g 's of 30, 40, and 50 nm.     

Effect of Composition on Thermoelectric Properties in PbTe-Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript> Composites

The solidification of alloys in the Bi₂Te₃-PbTe pseudobinary system at off- and near-eutectic compositions was investigated for their microstructure and thermoelectric properties. Dendritic and lamellar structures were clearly observed due to the phase separation and the existence of a metastable ternary phase. In this system, three phases with different compositions were observed: binary Bi₂Te₃, PbTe, and metastable PbBi₂Te₄. The Seebeck coefficient, electrical resistivity, and thermal conductivity of ternary alloys as well as binary compounds were measured. The phonon thermal conductivities of Pb-Bi-Te alloys were lower than those in binary PbTe and Bi₂Te₃, which could have resulted from the increased interfacial area between phases due to the existence of the metastable ternary phase and the resultant phase separation.     

The Fabrication and Characterization of Single‐Component Polymeric White‐Light‐Emitting Diodes

By using Ni⁰‐mediated polymerization, we have systematically synthesized a series of fluorene‐based copolymers composed of blue‐, green‐, and red‐light‐emitting comonomers with a view to producing polymers with white‐light emission. 2,7‐Dibromo‐9,9‐dihexylfluorene, {4‐(2‐[2,5‐dibromo‐4‐{2‐(4‐diphenylamino‐phenyl)‐vinyl}‐phenyl]‐vinyl)‐phenyl}‐diphenylamine (DTPA), and 2‐{2‐(2‐[4‐{bis(4‐bromo‐phenyl)amino}‐phenyl]‐vinyl)‐6‐tert‐butyl‐pyran‐4‐ylidene}‐malononitrile (TPDCM) were used as the blue‐, green‐, and red‐light‐emitting comonomers, respectively. It was found that the emission spectra of the resulting copolymers could easily be tuned by varying their DTPA and TPDCM content. Thus with the appropriate red/green/blue (RGB) unit ratio, we were able to obtain white‐light emission from these copolymers. A white‐light‐emitting diode using the polyfluorene copolymer containing 3 % green‐emitting DTPA and 2 % red‐emitting TPDCM (PG3R2) with a structure of indium tin oxide/poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonic acid)/PG3R2/Ca/Al was found to exhibit a maximum brightness of 820 cd m^–2 at 11 V with Commission Internationale de L'Eclairage (CIE) coordinates of (0.33,0.35), which are close to the standard CIE coordinates for white‐light emission (0.33,0.33).