基于PCI总线的中文字符液晶屏显示设计

介绍一个汉字点阵屏幕显示电路的组成、工作原理及其实现.着重介绍了PLX9052的ISA接口模式配置、WDM驱动程序地址重定位以及与应用程序的通信的原理及方法.最后给出汉字屏幕显示效果图.     

过氧化甲乙酮合成研究

论述了过氧化甲乙酮的合成方法，用阳离子交换树脂催化剂代替传统的无机酸催化剂。考察了离子交换树脂用量、反应温度对反应产率、活性氧含量的影响及溶剂对产品稳定性的影响。     

聚丙烯酸钠类高吸水性树脂的研究

采用反相悬浮聚合法合成高吸水性树脂.将丙烯酸(单体,水相)用氢氧化钠部分中和,然后与环己烷(溶剂,油相)共混,用水溶性的过硫酸钾做引发剂,N,N-亚甲基双丙烯酰胺做交联剂,在一定的反应温度和时间下,得到聚丙烯酸钠高吸水性树脂.     

基于USB的155 Mb/s码型发生器的研制

介绍了一种带USB接口的光的155Mb／s码型发生器。伪随机码和其他格式的码型由PC产生通过USB接口进入双口RAM，再经串并变换后由光发射模块发射。该系统可方便地设定各种格式的码型，并同时具备光接口和电接口，可广泛应用于光通信各种实验中，具有重要的实用价值。     

潜油电机碟形弹簧的动力学分析

为了降低潜油电泵机组的振动对止推轴承性能的影响,在潜油电机中节和下节的止推轴承静块底部安装了蝶形弹簧。用有限元方法进行模态分析,确定了蝶形弹簧的主振型和固有频率,然后进行瞬态动力学分析,求解蝶形弹簧在一定载荷下的应力和位移。依此设计的蝶形弹簧将进一步延长止推轴承的使用寿命。     

降低气体悬浮焙烧炉焙烧过程中Al_2O_3粒度破损的措施

为了降低气体悬浮焙烧炉焙烧过程中Al_2O_3粒度的破损,对气体悬浮焙烧炉焙烧过程中氧化铝粒度的影响因素进行了分析,提出了降低粒度破损的一些措施。     

Quality assurance

BACKGROUND: The treatment of pediatric empyemas remains controversial. While thoracentesis and tube thoracostomy appear adequate for relatively benign organisms, virulent bacteria cause thick fibrinous pleural peels entrapping the lung. Open thoracotomies have been effectively used for decortication but are painful. METHODS: We report the use of minimally invasive thoracoscopic decortication in 12 patients (mean age 5 years). All failed conventional management with persistent fever, increasing oxygen requirement, recurrent effusion, and pleural consolidation; 5- and 10-mm trocars were used and complete decortication was accomplished. RESULTS: Ten of 12 patients were afebrile by 72 h and discharged 4-12 days after surgery. Eleven of 12 patients had clear chest x-rays by 1 month. CONCLUSION: Thoracoscopic decortication is a safe and effective means of treating pediatric empyemas.     

超声波在金属凝固中的应用与发展

简要介绍了超声波及其基本特性，综述了高能超声对金属凝固过程作用方面的研究和应用状况，提出超声处理是改善金属凝固组织，提高力学性能的有效方法，并对21世纪超声凝固细晶技术的前景进行了展望。     

扭杆弹簧的波动传递特性分析

建立了扭杆弹簧的波动方程，提出求解扭杆弹簧传递特性的方法，并推导出弹性波在扭杆弹簧中的传递速度，对沿弹簧传播的位移、速度、应力、应变和作用力的传递特性进行了探讨。分析了扭杆弹簧弹性单波的求解方法及波动干涉问题。推导了弹簧的波阻公式，为扭杆弹簧的波动理论建模及实际应用提供参考。     

Microstructure and Mechanical Properties of Heat-treated GeSb_2Te_4 Thin Films

The effect of annealing on microstructure,adhesive and frictional properties of GeSb 2 Te 4 films were experimentally studied.The GeSb 2 Te 4 films were prepared by radio frequency(RF)magnetron sputtering,and annealed at 200℃and 340℃under vacuum circumstance,respectively.The adhesion and friction experiments were mainly conducted with a lateral force microscope(LFM)for the GeSb 2 Te 4 thin films before and after annealing.Their morphology and phase structure were analyzed by using atomic force microscopy(AFM)and X-ray Diffraction(XRD)techniques,and the nanoindention was employed to evaluate their hardness values.Moreover,an electric force microscope(EFM)was used to measure the surface potential. It is found that the deposited GeSb 2 Te 4 thin film undergoes an amorphous-to-fcc and fcc-to-hex structure transition;the adhesion has a weaker dependence on the surface roughness,but a certain correlation with the surface potential of GeSb 2 Te 4 thin films.And the friction behavior of GeSb 2 Te 4 thin films follows their adhesion behavior under a lower applied load.However,such a relation is replaced by the mechanical behavior when the load is relatively higher.Moreover,the GeSb 2 Te 4 thin film annealed at 340℃presents a lubricative property.