Bacteriological effects of functionalized cotton dressings

This study aims to achieve effects of improved hydrophilicity and microorganism inhibition, which are rarely simultaneously present in wound dressings. Cotton gauzes were modified using the grafting of a polymer-based β-cyclodextrin. After optimizing the grafting conditions, the untreated and modified cellulosic samples were principally characterized using FT-IR spectroscopy, TGA/DTA analysis, in vitro drug release, and wettability measurements. In light of desired characteristics of wound dressings, the effectiveness of procedures was evaluated. It was found that contact angles for cotton gauzes decreased after functionalization, which means that hydrophilicity was proven to become excellent. A successful Methylene Blue complexation was confirmed through measure of the dyebath exhaustion using UV-spectrophotometry. Then, during Methylen Blue release test, we reported an initial burst release of active ingredient over 7?h, followed by zero-order release. The treatment effect on antimicrobial activity was investigated by growth inhibition, which was proven against Staphylococcus aureus and Escherichia coli.     

Sensors fault diagnosis and fault tolerant control for grid connected PV system

This paper discusses a Sensors Fault Detection and Isolation (FDI) and Fault Tolerant Control (FTC) of three phase inverter for PV system application. All sensors used in the inverter control strategy are addressed in this work. The developed FDI algorithm focuses on residuals generation; it is defined by the different between measurement and reconstituted signal. So, estimators block are investigated, such as, two Models References Adaptive Systems (MRAS) are developed to reconstitute the information of three phase line currents and dc link voltage sensors. The reconstituted information is injected to the corresponding FDI algorithm. Grid voltage sensors FDI is presented in this contribution trough the use of scaled virtual flux estimator, based on Second Order Generalized Integrator and Frequency Looked Loop. When a fault detected, FTC is ensured by replacing the erroneous measurement by its corresponding estimator. Theoretical study and simulations results are presented to validate the effectiveness of the proposed method.     

Development of the high performance magnesium based hydrogen storage alloy

Series of MgNi type alloys with Ti, Al, Zr, Pd and Co additive elements were synthesized by mechanical alloying and their electrochemical hydrogen storage characteristics were investigated. Systematical alloy designing indicated that Mg_0.80Ti_0.15Al_0.05Zr_0.05Ni_0.95 alloy has the best electrode performance. The atomic fractions in this alloy were believed to be optimum to get the reasonable amount of hydrogen storage with the improved cyclic stability. Titanium was estimated to enter into Mg(OH)₂ layer during the discharging process and make this barrier layer more penetrable by elemental hydrogen. Al and/or Al-oxides were predicted to dissolve selectively throughout the barrier hydroxide layer and thus reduce the stability of this layer. The main contribution of Zr was estimated to arise from its large atomic size that Zr atoms can create extra sites for the elemental hydrogen in the alloy structure. As the alloy charge transfer resistances decreased, the alloy retention rates increased. Improvement in the alloy capacity retaining rate was also closely related with the hydrogen diffusion coefficients in the alloy.     

Investigation of water gas-shift activity of Pt–MOx–CeO2/Al2O3 (M = K,Ni, Co) using modular artificial neural networks

The water gas shift activity of promoted Pt–CeO₂/Al₂O₃ catalysts were investigated in this work. The catalysts were prepared by incipient to wetness impregnation and tested using a microflow reaction system. It was found that K has beneficial effects under product-containing feed compositions while Co and Ni promoters worsen catalyst performance. The reaction temperature and feed H₂O/CO ratio positively affect the catalytic activity, whereas CO₂ and H₂ addition to the feed decreases CO conversion, as expected. The experimental results were also modeled using modular neural networks, at which the catalyst preparation and operational (reaction) variables were used together in the same network because they are interacting but processed differently because they are dissimilar in their form (i.e. categorical versus continuous) and their effects on catalytic activity. It was concluded that the effects of catalyst preparation and operational variables and their relative importance could be comprehended more accurately by using this approach, which may be also employed in other similar systems.     

Innovative hydrogen release from sodium borohydride hydrolysis using biocatalyst-like Fe2O3 nanoparticles impregnated on Bacillus simplex bacteria

For the first time in this innovative study, microorganisms such as Bacillus simplex bacteria, mostly used in biological activity studies, are used as a bio-supporter agent of iron to release hydrogen from sodium borohydride hydrolysis at 25.0 ± 0.1 °C. The goal is to investigate thoroughly sodium borohydride hydrolysis catalyzed by Fe₂O₃ nanoparticles impregnated on microorganism such as Bacillus simplex (BS) bacteria (Fe₂O₃@BS NPs) known with strong antibacterial properties, which makes innovative them a candidate for hydrolysis reaction. This study was focused on the preparation, identification, and catalytic use of biocatalyst-like Fe₂O₃@BS NPs for hydrogen release from the sodium borohydride hydrolysis at 25.0 ± 0.1 °C. The characterization results made after and before hydrolysis reaction using by SEM/SEM-EDX, FT-IR, XRD, UV–vis, XPS, DLS, ELS Zeta potential, ESR, and TEM techniques reveal the formation of highly active, stable, durable, and long-lived biocatalysts-like Fe₂O₃@BS NPs.     

Experimental investigation on flow improvement in compressor cascades

There is no general rule in the literature to help choose a correct flow control device for any given case of turbomachinery applications. This suggests individual optimization of flow control devices for each specific case. The objective of this study is to prove experimentally the benefits of passive control methods in improving the compressor performance. This allows to reduce the fuel consumption, leading to energy saving and reduction of atmospheric pollution. Two features have been controlled in this study: flow separation over the blade surfaces and the secondary flow over the cascade endwalls. Vortex generator ribs are tested on the blade suction side for flow reattachment on the blade surfaces, and low‐profile vortex generators are tested on the side walls of the compressor cascade against secondary flow losses. Different vortex generator designs are compared for total pressure recovery, flow turning, boundary layer characteristics, and pressure distributions over the endwalls. Copyright © 2016 John Wiley & Sons, Ltd.     

Optical properties of sol–gel dip-coated Ta2O5 films for electrochromic applications

Amorphous Ta₂O₅ films were prepared by sol–gel dip process on different substrates. The dip-coating technique was used to prepare amorphous Ta₂O₅ films by hydrolysis and condensation of tantalum ethoxide, Ta(OC₂H₅)₅, precursor. Stable coating solutions were prepared using acetic acid as a chelating ligand and catalyzer. Single layer and multi-layered Ta₂O₅ films were fabricated at a dipping rate of 107 mm/min. The microstructure, stoichiometry and optical properties of these films were investigated as a function of the film thickness. Room temperature CV measurements clearly revealed a protonic conductor behavior for Ta₂O₅ films. Optical properties such as refractive index, extinction coefficient and optical band gap value of the Ta₂O₅ films were calculated from optical transmittance measurements. It was found that the refractive index and extinction coefficient values were affected by the thickness of the coatings. The refractive index at a wavelength of 550 nm increased from 1.70 to 1.72 with increasing film thickness. The optical band gap value (3.75±0.12 eV) of the coating was unaffected by the film thickness. These results indicate that sol–gel-deposited Ta₂O₅ films have a promising application as proton conductors in electrochromic devices.     

Optical and electrochemical characteristics of sol–gel deposited iron oxide films

Homogenous, crack free iron oxide films are prepared by the sol–gel spin coating technique from a solution of iron iso-propoxide and isopropanol. The films were characterized by X-ray diffractometry (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), UV-visible (UV–Vis) spectroscopy and cyclic voltammetry (CV). XRD of the films showed that they had an amorphous structure. The optical constants refractive index (n) and extinction coefficient (k) were measured by scanning spectrometer in the wavelength range of 390–990 nm. The n and k values were found n =2.3±0.01 and k =0.2±0.002 at 650 nm. The electrochemical behavior investigated in 0.5 M LiClO₄ propylene carbonate (PC) electrolyte-CV examinations showed good rechargeability of the Li⁺/e⁻ insertion extraction process beyond 300 cycles. Spectroelectrochemistry showed that these films exhibit weak cathodic coloration in the spectral range of 350–800 nm.     

Food safety practices among pregnant women and mothers in the women, infants, and children program, Miami, Florida

Pregnant women and infants are two groups at the highest risk of severe outcomes from foodborne illnesses. We surveyed adult clients of a Women, Infants, and Children (WIC) clinic serving predominately African Americans in inner-city Miami, Florida, to assess food safety practices. Eligible and consenting women completed a 23-item self-administered survey with questions concerning food handling practices around the Partnership for Food Safety Education's Fight BAC! campaign constructs of "clean", "separate" (not cross-contaminated), "cook", and "chill". Of 342 eligible clients, 299 (87.4%) consented to participate. In general, the clients' food safety practices were most problematic in the cook and chill constructs. Using a cooking thermometer, refrigerating foods within 2 h, and thawing them safely were the least commonly reported safe practices. Women who were pregnant with their first child had the lowest food safety practice scores. Of the 62 pregnant participants, 32 (51.6%) reported eating hot dogs or deli meats without first reheating them some of the time or more often, and 22 (35.5%) reported eating soft cheeses and blue-veined cheeses some of the time or more often, putting the women at risk of listeriosis. Although all women in the WIC program could benefit from food safety education, these findings indicate that women during their first pregnancy should especially be targeted for food safety education.