Optical-transmission characteristics of optical-fiber cables and installed optical-fiber cable networks for WDM systems

Many cables containing 1.3-/spl mu/m zero-dispersion single-mode (SM) optical fibers are installed in trunk and access networks. Recently, there have been a number of studies on wavelength-division-multiplexing (WDM) systems designed to increase transmission capacity and flexibility. If we can construct WDM systems using SM optical-fiber cable networks designed to transmit using wavelengths in the 1.3-/spl mu/m window (O-band), this will prove very effective in reducing construction costs. It is therefore important to examine the wavelength dependence of the transmission characteristics of SM optical-fiber cables and networks that have already been installed and in which several optical fibers are joined. In this paper, we describe the measured optical characteristics of SM optical-fiber cables and installed optical-fiber cable networks at various wavelengths. The optical characteristics were stable in the 1.46 to 1.625-/spl mu/m wavelength range and we confirmed that the installed SM optical-fiber cable networks could be used for WDM system applications.     

Microscale Patterning of Mesoscopic PZN-PT Single Crystal Films by Crystal ion Slicing and Laser-Induced Etching

Advances in the fabrication of solid-solution single crystal relaxor ferroelectrics have made it possible to produce highly efficient piezoelectric crystals, and have attracted renewed interest in the use of these crystals for a new generation of piezoelectric transducers, actuators and sensors. Of particular interest is their incorporation into micro-electromechanical systems (MEMS). In this paper we report on the laser-induced wet chemical etching of lead zinc niobate-lead titanate (PZN-PT) in hydrochloric acid (HCl). Argon-ion laser radiation at power levels up to 4 W is focused to a spot diameter of about 15μm and results in the chemical etching of grooves at patterning speeds up to 5μm/sec. Crystal ion slicing, an ion-implant-based film separation technique, is used in combination with laser etching to form 5 to 10μm-thick patterned and freestanding films for incorporation into micro-electromechanical devices.     

Using the magneto-optical Kerr effect to study magnetization processes in two-dimensional magnonic crystals based on YIG thin films

The magneto-optical Kerr effect for red (628 nm) and green (532 nm) light is used to study magnetization processes in 2D magnonic crystals obtained by etching pits with the diameter D ≈ 32 μm to a depth of t ≤ 2 μm in a 16.1-μm-thick film of yttrium iron garnet (YIG). Hysteresis loops obtained in the case of the inplane crystal magnetization at 628 nm are characterized by lower saturation fields H _s and higher remanent magnetizations than those obtained at 532 nm, a result that is attributed to different absorption coefficients of the YIG film at these wavelengths. This difference between the magnetization curves reflects the fact that the magnonic-crystal surface probed with the green light makes a greater contribution to the magneto-optical Kerr effect. Therefore, the green light is more sensitive to the demagnetizing fields, which govern magnetization processes in the magnonic crystals.     

Training and optimization of an artificial neural network controlling a hybrid power filter

A hybrid power compensator (HPC) consisting of a static VAr compensator and a dynamic compensator needs to be optimally controlled during the compensation of nonlinear loads. The HPC must be controlled to meet minimum requirements in terms of power factor and harmonic distortion, while at the same time minimizing its total cost. An artificial neural network (ANN) is used to control the HPC amidst a very dynamic power system environment. The performance of a reference ANN is evaluated while controlling an HPC connected to a typical nonlinear industrial load. The training and performance of the ANN is then optimized in terms of training set size, training set packing and ANN topology and the performance compared to the reference ANN. This paper highlights the importance of optimising the mentioned ANN parameters to achieve optimum ANN training and modeling accuracy. The results obtained reveals that the application of an ANN in controlling an HPC is feasible given that the ANN parameters are chosen appropriately.     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

Simulating strength and failure in engineering plant

Current features are considered in the calculation of carrying capacities for constructions in engineering plant (EP). Methods and algorithms are described for EP calculations with comprehensive incorporation of the effects from technological and working defects on the behavior of structures under standard and emergency conditions. __________ Translated from Khimicheskoe i Neftegazovoe Mashinostroenie, No. 8, pp. 38–40, August, 2006.     

Management gaps analysis: a case study of groundwater resource management in New Zealand

The primary objective of this project is to identify gaps, whether real or perceived, that hinder effective groundwater management in New Zealand. These gaps show as gaps in information, gaps in implementation, gaps in technological and management tools, and gaps in understanding of fundamental processes. The secondary objective is to propose a management strategy to close the identified gaps. Several methods are used to meet these objectives: surveys distributed to selected staff in each regional council; the review of various written reports; the analysis of land-use databases; and private consultation within each regional council. Results show that groundwater management in New Zealand is generally reactionary with the main gaps being in strategic planning and national guidelines. Most gaps appear to be predominantly information and implementation issues. In some cases there are gaps in the understanding of fundamental processes within an aquifer system, including the long-term effects of land-use on groundwater quality. An adaptive management approach is suggested as a means of closing these gaps.     

Use of citric acid for heavy metals extraction from contaminated sewage sludge for land application.

Recent studies revealed that organic acids such as citric and oxalic acids seemed to be more promising as chemical extracting agents for removal of heavy metals from contaminated sludge, since they are biodegradable and can attain a higher metal extraction efficiency at mildly acidic pH compared to other extracting agents. Results of a lab-scale study on the efficiency of citric acid in the extraction of chromium (Cr), copper (Cu), lead (Pb), nickel (Ni) and zinc (Zn) from anaerobically digested sludge, revealed that citric acid seemed to be highly effective in extracting Cr (at 100%), Cu (at 88%), Ni (at 98%) and Zn (at 100%) at pH 2.33, mostly at 5 days leaching time except for Cu and Zn, which are at 1 day and 2 h contact times respectively. Lead removal at the same pH was also high at 95% but at a longer leaching time of 11 days. At pH 3, citric acid seemed to be highly effective in extracting Pb (at 100%) at 1 day leaching time, although higher removals were also attained for Ni (70%) and Zn (80%) at only 2 h leaching time. Chemical speciation studies showed that Cr, Cu and Ni in the sludge sample seem to predominate in residual fractions, while Pb and Zn were found mostly bound to organic and inorganic matter forms, hence the potential of the sludge for land application.