Tar sand extractions with microemulsions: I-the dissolution of light hydrocarbons by microemulsions using 2-butoxyethanol and diethylmethylamine as cosurfactants

For oil sand extractions with microemulsions it is important to disperse large quantities of light hydrocarbons in an aqueous medium. Fundamental studies on the properties of 2-butoxyethanol (BE) and diethylmethylamine (Et₂McN) in water suggest that these two liquids could be more effective cosurfactants than the usual alcohols used for this purpose. The phase diagrams of microemulsions using BE and Et₂MeN as cosurfactants, combined with typical ionic and non-ionic surfactants and typical aliphatic and aromatic hydrocarbons, were therefore investigated and compared with microemulsions based on n-butanol. Although the phase diagrams depend significantly on the nature of the surfactant and of the oil, the monophasic region generally increases with the cosurfactant in the order n-butanol < Et₂McN < BE. With the active mixture BE-cetyltrimethylammonium bromide, temperature has little effect on the phase diagram and NaCl generally destabilizes the microemulsion.     

Catalytic Combustion of Model Carbon Particles (CPs) over Pt/β-SiC Catalyst

Platinum catalyst supported on a medium surface area -SiC was successfully used for the catalytic combustion of model carbon particles and compared to a catalyst supported on a low surface area -SiC. The -SiC-based catalyst showed no deactivation as a function of cycling tests while a strong deactivation was observed on the -SiC-based catalyst. This deactivation was attributed to the progressive encapsulation of the platinum particles by a layer of silica which built up during the combustion cycle. These results render possible the use of Pt/-SiC catalyst as a diesel carbon particle catalytic filter with continuous regeneration.     

Chlorophyll adsorption on acid-activated clay

An acid-activated clay (Çanakkale montmorillonite from Turkey) was used to adsorb chlorophyll from hexane solutions. The phenomenon seems to be mainly driven by the interaction of chlorophyll with acid sites. The adsorption of chlorophyll on Brönsted acid sites was indicated by a characteristic infrared band for the -OH group at 3671 cm^?1. The variations in the structure of clay mineral and chlorophyll during adsorption have been examined by differential thermal analysis, thermogravimetry and infrared spectroscopy of the activated clay before and after adsorption of chlorophyll. Oxidation of adsorbed chlorophyll was completed at quite a high temperature.     

(BaTiO3)1-x + (Co0.5Ni0.5Nb0.06Fe1.94O4)x nanocomposites: Structure,morphology, magnetic and dielectric properties

Two phase-based nanocomposites consisting of dielectric barium titanate (BaTiO₃ or BTO) and magnetic spinel ferrite Co_0.5Ni_0.5Nb_0.06Fe_1.94O₄ (CNNFO) have been synthesized through solid state route. Series of (BaTiO₃)_1-x + (Co_0.5Ni_0.5Nb_0.06Fe_1.94O₄)_x nanocomposites with x content of 0.00, 0.25, 0.50, 0.75, and 1.00 were considered. The structure has been examined via X-rays diffraction (XRD) and indicated the occurrence of both perovskite BTO and spinel CNNFO phases in various nanocomposites. A phase transition from tetragonal BTO structure to cubic structure occurs with inclusion of CNNFO phase. The average crystallites size of BTO phase decreases, whereas that for the CNNFO phase increases with increasing x in various nanocomposites. The morphological observations revealed that the porosity is highly reduced, and the connectivity between grains is enhanced with increasing x content. The optical properties have been investigated by UV−vis diffuse reflectance spectroscopy. The deduced band gap energy (E_g) value is found to reduce with increasing the content of spinel ferrite phase. The magnetic as well as the dielectric properties were also investigated. The analysis showed that CNNFO ferrite phase greatly affects the magnetic properties and dielectric response of BTO material. The obtained findings can be useful to enhance the performances of magneto-dielectric composite-based systems.     

Evaluation of the removal of n-butanol vapor by the poly(lactic acid)-zeolite-TiO2 composite and formation of by-products

The use of polymeric films incorporated with zeolite-TiO₂ composites associated with UV radiation can be an alternative in the removal of volatile organic compounds (VOCs) through the adsorption and photodegradation processes. This study produced poly(lactic acid) (PLA) films incorporated with 13× zeolite, TiO₂, and 13×-TiO₂ zeolite composite to remove n-butanol and evaluate the by-products generated in the process. The results showed that 13× zeolite and TiO₂ added individually or as a composite to PLA, gave the polymer matrix a significant increase in the removal capacity of n-butanol. The best performance was presented by the zeolite-TiO₂, composite, confirming a synergistic effect. However, the formation of CO and CO₂ exceeded the expected values, with the verification that the polymeric matrix underwent photodegradation action by TiO₂. The polymeric film only containing zeolite is the most suitable for the removal of VOCs, as it did not present degradation of the PLA, generating a lower concentration of by-products.     

Bi-layer gelatin active films with “Pitanga” leaf hydroethanolic extract and/or natamycin in the second layer

Research on biopolymers-based active films produced with natural antioxidants and/or antimicrobials has gained attention over the last few years; however, anti-mold activity has been less studied than those of anti-bacteria. The aim of this work was the development and characterization of bi-layer films based on gelatin with natamycin and/or “Pitanga” leaf hydroethanolic extract in the second thin layer in order to determine the effects of these bioactive compounds on bi-layered film properties. The films were characterized regarding their moisture content and solubility in water, optical properties, microstructure, mechanical and thermal properties, water contact angle, water vapor permeability, UV/visible light transmission, X-ray diffraction, Fourier transform infrared (FTIR) spectroscopy, and antioxidant and anti-mold activities. Active films presented activity against Penicillium spp and Aspergillus niger and demonstrated antioxidant activity, as measured by ABTS ^•+ and DPPH ^• methods. Neither additive used in the films' second layer significantly affected the films' moisture content, thermal properties or the molecular interactions of the polymer matrix, assessed by FTIR, although some mechanical properties were affected, and the water contact angle. In conclusion, bi-layer films have reduced the quantity of additives required to maintain the antioxidant and anti-mold activities, as compared to similar monolayer films of the same thickness.     

Production of NiO,NiO/Ag,NiO/Au,and NiO/Pt hollow spheres by using block copolymer stabilized microspheres as a template

Hollow spheres of nickel oxide (NiO) and silver, gold, and platinum nanoparticle loaded NiO composites were successfully produced by using polystyrene (PS) latexes as hard template. Due to the presence of tertiary amine based diblock copolymer stabilizer on the surface of PS, the tertiary amine functional groups provided homogene deposition of nickel hydroxide, and then the precursor NiO salt production on the surface of PS latexes with a controlled precipitation technique. Then, NiO and NiO/metal NP hollow spheres were produced by calcination at 600 °C. Thermogravimetric analysis indicated that the amounts of NiO and NiO-composite after calcination were in the range of 21.1–29.7 wt%. The diameters of metal oxide spheres were in the range of 2.0–2.7 μm and the shell thickness were in the range of 250–350 nm. These structures had very low densities due to their porous and hollow structures and had outer layers with highly rough surfaces due to formation of nanosheets, which may offer important advantages for catalysis studies.     

Properties of Induction Plasma Sprayed Iron Based Nanostructured Alloy Coatings for Metal Based Thermal Barrier Coatings

Metal-based thermal barrier coatings (MBTBCs) have been produced using high frequency induction plasma spraying (IPS) of iron-based nanostructured alloy powders. The study of MBTBCs has been initiated to challenge issues associated with current TBC materials such as difficult prediction of their “in-service” lifetime. Reliability of TBCs is an important aspect besides the economical consideration. Therefore, the study of MBTBCs, which should posses higher toughness than the current TBC materials, has been initiated to challenge the mechanical problems of ceramic-based TBCs (CBTBCs) to create a new generation of TBCs. The thermal diffusivity (TD) (α) properties of the MBTBCs were measured using a laser flash method, and density (ρ) and specific heat (C _p) of the MBTBCs were also measured for their thermal conductivity (k) calculation (k = αρ C _p).