80 GHz silicon diamond-heatsink Impatt diodes

80 GHz band silicon d.d.r. Impatt diodes with diamond heatsinks were fabricated. An output power of 1014 mW at 77.70 GHz was obtained by liquid-nitrogen-cooled operation, which gives the highest pf2 product, and 726 mW at 73.35 GHz by room temperature operation. Small-signal diode impedance was calculated considering operating temperature.     

ESCA study on the mechanism of adherence of metal to silica glass

Indium oxide films formed on the surface of silica glass samples by selective oxidation have been shown to greatly improve the adherence of gold-indium alloy to the silica glass. In order to clarify the role that the oxide films play in the reaction, thin indium films have been evaporated onto silica glass and heated at temperatures of between 973 and 1473 K, both in air and in hydrogen gas. Electron spectroscopy for chemical analysis (ESCA) measurements have then been made to investigate the chemical environments around oxygen and indium atoms at the reacting interface between the oxide and glass. Measured 01s and In3d _5/2 spectra reveal the formation of non-bridging oxygen atoms at the interface, in addition to the original bridging oxygen atoms in silica glass. Introduction of the non-bridging oxygen atoms and indium ions into the silica glass is concluded to be an essential factor in promoting good adherence between the gold alloy and silica glass.     

Effect of hypothermic anoxic cardioplegia on myocardial contractility

Dynamic brain scintigraphy was performed on seven patients with documented hydrocephalus of various aetiologies. The patients had a characteristic abnormality consisting of lateral displacement of the proximal middle cerebral activity associated with a paracentral lucent zone. No focal areas of increased activity were identified on the static brain images. A proposed mechanism for these findings is discussed.     

Adsorption mechanism of copper and cadmium onto defatted waste biomass

In this study, the amount of copper or cadmium adsorbed using waste biomass (i.e., coffee grounds (CG) and rice bran (RB)) was investigated. The amount of crude protein in defatted CG (D-CG) or RB (D-RB) was greater than that in CG or RB, respectively. The amount of copper or cadmium adsorbed using CG was greater than that using RB. Additionally, the amount of copper or cadmium adsorbed was not affected by the presence of fat in CG. Adsorption data was fitted to the Freundlich equation, and the correlation coefficients were in the range of 0.794-0.991. The main adsorption mechanism was thought to be monolayer adsorption onto the surface of the waste biomass. The adsorption rate data was fitted to the pseudo-second-order model, and the correlation coefficient average was in the range of 0.891-0.945. This result showed that the rate-limiting step may be chemisorption. Moreover, the amount of copper or cadmium desorbed from CG or RB using 0.01 mol/L or 1.00 mol/L HNO(3) was investigated. Desorption with 0.01 mol/L HNO(3) resulted in the recovery of 86-97% of the copper and cadmium, indicating that copper or cadmium that was adsorbed using waste biomass was recoverable.     

Phosphate adsorption ability of granular gibbsite and cerium hydroxide

In the present study, the phosphate adsorption abilities of granular materials, gibbsite (GB) and cerium hydroxide (CE), granulated with ethyl cellulose and ethanol, were investigated. For suitable granular conditions using GB or CE, the percentage of binder and amount of solvent were 10% and 3.25 mL/5 g for GB and 7.5% and 2.50 mL/5 g for CE. The amount of phosphate adsorbed by granular GB or CE was similar to that adsorbed by powdered GB or CE. The adsorption isotherms of phosphate were also similar for the granular and powdered materials. The results of a column experiment showed that when GB was used, the suitable concentration of sodium hydroxide as the desorption solution was 2 mmol/L. In these experiments, the amount of phosphate adsorbed was 31.4 mg/g, the amount of phosphate desorbed was 25.3 mg/g, and the recovery percentage was 80.5%. In contrast, when CE was used, the suitable concentration of sodium hydroxide was 500 mmol/L; the amount of phosphate adsorbed was 77.7 mg/g, the amount of phosphate desorbed was 57.8 mg/g, and the recovery percentage was 74.4%. Results also indicate that granular GB and CE could be used at least five times in a column without loss of absorption or desorption abilities. Moreover, granulation of GB and CE is possible using ethyl cellulose and ethanol.     

Low temperature preparation and machinability of porous ceramics from talc and foamed glass particles

Porous ceramics were prepared by firing mixtures of talc (Mg₃Si₄O₁₀(OH)₂) and foamed glass particles (ceramic balloons, CB) with and without LiCl as a sintering acid. The mixing ratios of the starting materials were talc:CB = 7:3, 8:2, 9:1 and 10:0, with additions of LiCl of 0, 2 and 5 mass%. The mixtures were formed into pellets and fired at 600–1000 °C. The pellets without LiCl showed very poor strength even when fired at 1000 °C but those containing LiCl were much stronger, even when fired at only 600 °C. The crystalline phases in these samples changed to enstatite (MgSiO₃) at ≥ 700 °C by decomposition of the talc under the fluxing action of the LiCl. The resulting samples were machinable and easily cut and drilled. The cutting rate decreased with increasing bending strength, for example, from 105 mm²/s and 6.3 MPa to 50 mm²/s and 16.3 MPa, respectively. The drilling rate of the present sample was found to be only slightly less than Teflon (polytetrafluoroethylene, PTFE) but much faster than graphite, glass ceramics, etc.     

Plasma enhanced in situ chamber cleaning evaluated byextracted-plasma-parameter analysis

We have demonstrated that high-efficiency in situ chamber cleaning with short gas residence time is possible for SiO₂ etching chambers by use of NF₃ plasma, and that the endpoint determination of the cleaning is possible by monitoring the optical emission intensities of CO or H. Nitrogen trifluoride (NF₃), which has a low N-F bond energy, can generate a plasma with a high density of ions and radicals featuring low kinetic energy. The cleaning efficiency of several halogenated-gas plasmas has been evaluated based on extracted-plasma-parameter analysis. In this analysis important plasma parameters, such as ion energy and ion flux density, can be extracted through a simple rf waveform measurement at the plasma excitation electrode. The accuracy of this technique has been confirmed with a newly developed rf plasma direct probing method and by ion current measurements     

A feasibility study of an 8-MWh flywheel-type power storage system using oxide superconductors

When combined with a magnet having a magnetic field gradient (for example, a permanent magnet), a Y-based oxide superconductor is capable of forming a noncontact bearing with a strong levitational force. Since this bearing exhibits low rotational loss, it is very likely to form a highly efficient power storage system in combination with a flywheel. In this paper, an 8-MWh power storage system utilizing a flywheel was designed conceptually to examine its applicability and the possible effects of its introduction. It was found that this system was an effective power storage.