Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

Influence of geosynthetic reinforcement on the stability of an embankment with rigid columns embedded in an inclined underlying stratum

Incompressible dipping substrata are commonly encountered in engineering practice. Compared to horizontal underlying strata, the inclined underlying stratum increase the risk of collapse of embankments reinforced with columns because it weakens the restraint of the column base. The objective of this study is to investigate the effectiveness of geosynthetics on improving the embankment stability when the underlying stratum is inclined. The influence of geosynthetic tensile stiffness on the ultimate surcharge and failure mechanism is studied. A deep-seated failure with column tilting occurs when the geosynthetic tensile stiffness is low, whereas a lateral sliding occurs when the geosynthetic tensile stiffness is high. To illustrate the contribution of geosynthetics, the distribution of the lateral pressures acting on the columns is analyzed.     

面向草莓抓取的气动四叶片软体抓手研制

农林业中果蔬的自动化采摘需求日趋强烈,末端抓手是实现无损采摘的关键。传统的末端抓手以刚性结构居多,现有的各种柔性抓手也存在抓取力不足、包覆性不佳等缺点。本文以草莓的无损采摘为研究对象,提出将草莓外部轮廓曲线作为设计曲线,设计了一种新型气动四叶片软体抓手。首先,对软体抓手的结构做仿真优化,提出一种安全地附着在目标物表面的设想。然后,在进行草莓表面的最小破坏应力试验的基础上,测试了软体抓手的末端力,验证了其实现无损抓取的可行性。再次,利用动态捕捉技术,研究了软体抓手叶面的弯曲变形规律。最后,选择使用弧线型气体通道的软体抓手进行了草莓抓取测试,结果证明了气动四叶片软体抓手可以实现草莓的无损抓取,抓取成功率达90%,破损率为2%,表明所研制的四叶片软体抓手用于草莓抓取时具有良好的稳定性和实用性,可用于草莓采摘的末端执行器。本研究也可为其他易损果蔬的采摘技术提供理论基础和技术支撑。     

Spreading and Curing Behaviors of a Thermosetting Droplet-Silicone on a Heated Surface

Thermosetting materials are widely used as encapsulation in the electrical packaging to protect the core electronic components from external force, moisture, dust, and other factors. However, the spreading and curing behaviors of such kind of fluid on a heated surface have been rarely explored. In this study, we experimentally and numerically investigated the spreading and curing behaviors of the silicone(OE6550 A/B, which is widely used in the light-emitting diode packaging) droplet with diameter of ～2.2 mm on a heated surface with temperature ranging from 25 ℃ to 250 ℃. For the experiments, we established a setup with high-speed camera and heating unit to capture the fast spreading process of the silicone droplet on the heated surface. For the numerical simulation, we built a viscosity model of the silicone by using the Kiuna's model and combined the viscosity model with the Volume of Fluid(VOF) model by the User Defined Function(UDF) method. The results show that the surface temperature significantly affected the spreading behaviors of the silicone droplet since it determines the temperature and viscosity distribution inside the droplet. For surface temperature varied from 25 ℃ to 250 ℃, the final contact radius changed from ～2.95 mm to ～1.78 mm and the total spreading time changed from ～511 s to ～0.15 s. By further analyzing the viscosity evolution of the droplet, we found that the decreasing of the total spreading time was caused by the decrease of the viscosity under high surface temperature at initial spreading stage, while the reduction of the final contact radius was caused by the curing of the precursor film. This study supplies a strategy to tuning the spreading and curing behavior of silicone by imposing high surface temperature, which is of great importance to the electronic packaging.     

Tuning the Operating Band of an Artificial Magnetic Conductor

Journal of Communications Technology and Electronics - Approximate formulas for calculating the coefficient of reflection from an artificial magnetic conductor (AMC) based on a capacitive lattice...     

Dissolution of Metal Oxides in a Choline Chloride–Sulphosalicylic Acid Deep Eutectic Solvent

Theoretical Foundations of Chemical Engineering - A choline chloride–sulfosalicylic acid deep eutectic solvent (DES) is proposed for dissolving the oxides Co(II), Cu(II), Zn(II), Fe(III),...     

Calculation and Experimental Determination of the Neutronics Characteristics of the IRT-T Research Reactor

Atomic Energy - The results of calculations and experimental determination of the neutronics characteristics of the IRT-T research reactor are presented. The IRT-T reactor is a pool reactor with...     

Cyclic thermal shock resistance of h-BN composite ceramics with La2O3–Al2O3–SiO2 addition

The effects of La₂O₃–Al₂O₃–SiO₂ addition on the thermal conductivity, coefficient of thermal expansion (CTE), Young's modulus and cyclic thermal shock resistance of hot-pressed h-BN composite ceramics were investigated. The samples were heated to 1000 °C and then quenched to room temperature with 1–50 cycles, and the residual flexural strength was used to evaluate cyclic thermal shock resistance. h-BN composite ceramics containing 10 vol% La₂O₃–Al₂O₃ and 20 vol% SiO₂ addition exhibited the highest flexural strength, thermal conductivity and relatively low CTE, which were beneficial to the excellent thermal shock resistance. In addition, the viscous amorphous phase of ternary La₂O₃–Al₂O₃–SiO₂ system could accommodate and relax thermal stress contributing to the high thermal shock resistance. Therefore, the residual flexural strength still maintained the value of 234.3 MPa (86.9% of initial strength) after 50 cycles of thermal shock.