On the problem of hydrogen removal during heat treatment of large forgings

The solutions to a differential equation for the problem of heating of a cylinder in a medium with a fixed temperature are used to obtain equations for estimating the change in the hydrogen concentration in forgings from data on the hydrogen concentration at the cylinder axis or on the average bulk hydrogen concentration. Similar equations are also obtained for forgings having square cross sections. The calculation demonstrates that, for the case of a twofold decrease in the hydrogen concentration in a forging, the calculated times of annealing of a cylindrical forging differ by three times.     

Word length and lexical activation: Longer is better.

Many models of spoken word recognition posit the existence of lexical and sublexical representations, with excitatory and inhibitory mechanisms used to affect the activation levels of such representations. Bottom-up evidence provides excitatory input, and inhibition from phonetically similar representations leads to lexical competition. In such a system, long words should produce stronger lexical activation than short words, for 2 reasons: Long words provide more bottom-up evidence than short words, and short words are subject to greater inhibition due to the existence of more similar words. Four experiments provide evidence for this view. In addition, reaction-time-based partitioning of the data shows that long words generate greater activation that is available both earlier and for a longer time than is the case for short words. As a result, lexical influences on phoneme identification are extremely robust for long words but are quite fragile and condition-dependent for short words. Models of word recognition must consider words of all lengths to capture the true dynamics of lexical activation. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Volumetric out-of-furnace heat treatment of 3600-M3 decomposers

Specifications require that all the welds in 12-m-diam. decomposers with a capacity of 3600 m³ be subjected to high-temperature tempering before going into service in order to alleviate the stresses from the welding operation. Specialists at the organizations VNIIPTkhimnefteapparatury and VNIImontazhspetsstroi have proposed out-of-furnace volumetric (complete) of the assembled decomposer with the use of special heaters. The use of this heating method has shortened assembly operations while providing the welds with a highquality heat treatment and reducing the stresses overall (including welding stresses, stresses from assembly of the decomposer, etc.) The technology ensures uniform heating of the housing of the decomposer and provides for close control over the process. The experience gained in heat-treating decomposers can also be used in the construction of other containers that come into contact with corrosive media. __________ Translated from Metallurg, No. 3, pp. 61–64, March, 2006.     

Atomistic simulations of grain boundary migration in copper

While the motion of twist boundaries can be readily studied by atomistic simulations with molecular dynamics (MD) under the action of an elastic driving force, the approach fails for tilt boundaries. This is due to the interaction of the elastic stress with the grain boundary (GB) structure, which causes plastic strain by GB sliding. A novel concept, the orientation correlated driving force, is introduced to circumvent this problem. It is shown that this concept can be successfully applied to the study of the migration of tilt boundaries. The migration behavior of several twist and tilt GBs was investigated. The transition from low-to high-angle boundaries can be captured, and a structural transition of tilt boundaries was found at high temperatures, which also affected the migration behavior. The results compare well with experimental results of the motion high-angle boundaries, but for low-angle boundaries, the agreement is poor. This article is based on a presentation made in the “Hillert Symposium on Thermodynamics & Kinetics of Migrating Interfaces in Steels and Other Complex Alloys,” December 2–3, 2004, organized by The Royal Institute of Technology in Stockholm, Sweden.     

On-line estimation of kinetic parameters in anaerobic digestion using observer-based estimators and multiwavelength fluorometry.

Observer-based estimators (OBE) were used for estimation of state variables and kinetic parameters in an anaerobic digestion (AD) process. A simplified first-order model with time-varying kinetic parameters was used to design an OBE for kinetic parameter estimation. This approach was validated on a laboratory-scale anaerobic reactor equipped with a multiwavelength fluorometer for on-line measurements of COD and VFA concentrations in the reactor effluent. The proposed estimators provide continuous adjustment of kinetic parameters and can be used for predictions of state variables between samples acquisition and during sensor failure.     

Membrane separation of indigenous noroviruses from sewage sludge and treated wastewater.

In this study, feasibility of membrane separation for the removal of indigenous noroviruses (NVs) is evaluated. The indigenous NV gene was never detected from ultrafiltration (UF) permeates of sewage sludge and treated wastewater. Indigenous NV gene was also not detected from permeates of sewage sludge and treated wastewater by microfiltration (MF) with a pore size of 0.1 microm (MF0.1). Even though the pore size of MF (0.1 microm) was much larger than the diameter of virus particle (approximately 30-40nm), more than 4-log10 reduction value (LRV) at maximum was achieved by membrane separation with MF0.1. NV genes were often detected from permeates of sewage sludge and treated wastewater by MF with a pore size of 0.45 microm (MF0.45), although the maximum log10 reduction values were more than 3.59 for sewage sludge and more than 2.90 for treated wastewater. It is important to verify factors determining the removal efficiency of viruses with MF membranes.     

Influence of the second phase on the room-temperature tensile and creep deformation mechanisms of α-β titanium alloys: Part I. Tensile deformation

The effects of α and β phase interactions on the room-temperature tensile and creep deformation behavior of α + β titanium alloys with Widmanst?tten microstructures were studied using Ti-6.0 wt pct Mn and Ti-8.1 wt pct V as the model two-phase alloy systems. This article, Part I, deals with tensile deformation. It was found that when the α phase is present as thin (<10-μm) plates in the α + β alloys, significant twinning occurs. No significant twinning was observed in single-phase alloys with the same chemistry and similar grain size. Additionally, the β phase of Ti-8.1 V deforms by stress-induced hexagonal martensite (α′), while only twinning occurs in the single-phase β alloy with the same chemistry. Twinning in the α phase in association with stress-induced martensite (SIM) in the β phase was observed for the first time in a two-phase titanium alloy. This behavior is explained in terms of a number of factors including elastic interaction stresses between the α and β phases, coherency between the α phase and hexagonal martensite, and β phase stability.     

Identification of the adverse effect of nitrate on the phosphate release rate and improvement of EBPR process models.

The adverse effect of nitrate on the phosphate release rate in the anaerobic phase was observed and was hardly explainable with conventional EBPR process models. Four possible mechanisms were proposed including substrate competition, reduced fermentation, parallel reaction and sequential reaction. Batch experiments were designed and conducted to identify the dominant mechanism. Results showed that the sequential reaction was the only possible mechanism where only denitrification occurred if any nitrate existed in the anaerobic phase. Then the phosphate release following after the nitrate was completely removed. Nitrate inhibition effect was added into the PHA storage rate to incorporate the sequential reaction in the conventional ASM3 plus EAWAG bio-P module (ASM3 + P). Nitrate inhibition coefficient, K(I,NO,PAO) was found to be as low as 0.05 mg/L. This correlated well with experimental observation where no also meant that the anaerobic compartment of a continuous flow reactor could be seriously affected by the residual nitrate contained in the sludge recycle flow. This phenomenon caused overestimation of the phosphate uptake rate and consequently underestimation of PO4(3-) -P concentration. This problem was resolved by incorporation of a nitrate inhibition term in the ASM3 + P for more accurate simulation of the EBPR process.     

Design of a retention tank: comparison of stormwater quality models with various levels of complexity.

Stormwater quality simulation models are useful tools for the design and management of sewer systems. Modelling results are highly sensitive to experimental data used for calibration. This sensitivity is examined for three modelling approaches of various complexities (site mean concentration approach, event mean concentration approach and build-up, washoff and transport modelling approach) applied to a typical case study (design of a dry detention tank), accounting for the variability of calibration data and their effect on simulation results. Calibrated models with different calibration data sets were used to simulate 3 years of rainfall with different retention tank specific volumes. Annual pollutant load interception efficiencies were determined. Simulations results revealed (i) that there is no advantage in using the EMC model compared to the SMC model and (ii) that the BWT model resulted in higher design ratios than those given by the SMC/hydraulic approach. For both EMC and BWT models, using an increasing number n of events for calibration leads to narrower confidence intervals for the design ratios. It is crucial for design ratios to account for successive storm events in chronological order and to account for the maximum allowable flow to be transferred to the downstream WWTP.     

Catalytic epoxidation of olefins in the presence of a vanadyl porphyrin complex

It was found that vanadyl porphyrin complexes synthesized from petroleum metal porphyrin concentrates stimulated epoxidation during the olefin oxygenation process. The yields of obtained oxiranes turned out to be 38–75%, depending on the olefin structure. An epoxidation mechanism that suggests the formation of a protonated dioxygen adduct as an intermediate during oxygenation of olefins in the presence of vanadyl porphyrin complexes was proposed. An analogy is drawn between the epoxide formation reaction upon the catalytic oxygenation of olefins and the Prilezhaev reaction.