A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

Study of photosensitive mixtures of TMAE and helium, hydrocarbon or CF4-based carrier gases

Among the photocathodes used for particle identification based on the Cherenkov Ring Imaging technique, the TMAE molecule is still the best in terms of quantum efficiency. Despite the fact that TMAE gaseous photocathodes have already been used in a number of large experiments, one still seeks answers to many detailed questions. We present a systematic study of gaseous photocathodes based on TMAE mixed with helium, hydrocarbon and CF₄-based gases at normal pressure. The study includes a measurement of the electron drift velocity, gas quenching properties, single electron pulse height spectra and anode wire aging. The paper makes recommendations for carrier gas mixtures to obtain the best quenching, and suggests how to manage TMAE wire aging. This study was motivated by a specific particle identification detector proposal, the Fast Drift CRID proposed for the B-factory at SLAC.     

A Special Structure in Al-Mg-Li Alloy (01420) Weld Metal

A large quantity of laminated fine grain zones were observed in the Al-Mg-Li alloy weld metal by manual TIG, which was not found in ordinary Al alloy welds. The fine grain zone is formed because of the Al3(Zr,Ti) particles in the filler metal and the manual filling of filler metal in welding process     

CA／PAN中空纤维血浆分离膜的结构与性能

本研究以CA及PAN的共混溶液,通过干-湿法纺丝制取中空纤维,利用共混高聚物各组分在凝固剂中相分离速度的差异,形成具有稳定结构的中空纤维孔膜,该膜用于分离血液中的血浆成分具有良好效果。讨论了成型条件及添加剂等对膜结构、性能的影响,用SEM及图相分析仪、MAP压汞仪及DSC等分析手段,对膜的微孔结构、形态、孔尺寸及中空纤维膜的血浆通量和水通量等进行了系统的考查。     

纳米级BaAl_2O_4微粉的制备和性质

分别用溶胶 -凝胶法、低温固相反应法 ,制得了纳米级BaAl2 O4微粉 ,用电镜观察了其形貌和粒径的大小 ,用X-射线衍射仪进行了物相分析 ,测定了其纯度与晶型 ,讨论了制备方法与粒度大小的相互影响     

冷媒充填机的PLC控制

介绍了冷媒充填机控制系统的组成和工作原理，着重叙述了西门子S7－200可编程控制器与触摸屏结合的控制方式，使系统的性能得到较大的提高。     

利用反射纵波评价裂缝倾角的模拟实验研究

声波全波列测井中的反射纵波可以用来评价高角度裂缝和对井周附近地质结构进行成像。目前的研究主要侧重于直接从波形资料处理出发计算裂缝的位置和倾角 ,其可靠性和准确性无从评价和校验。文中采用模拟实验的方法记录了倾角为 6 0°～80°范围内的 8种倾角裂缝的反射脉冲纵波波形 ,自行推导了反演裂缝倾角的公式 ,结合波场分离技术对实验测量波形数据进行了处理 ,计算出的裂缝倾角与实际值具有良好的一致性。本文结果表明 ,利用至少 2个深度点的纵波反射波波形资料就可以准确地反演裂缝的倾角     

Recovery of fluorocarbons in Japan as a measure for abating global warming

The objective of this study is to evaluate the potential for recovering fluorocarbons as measures for the abatement of global warming. In this study, we focused on the three different kinds of fluorocarbons: CFCs, HCFCs and HFCs, and targeted refrigerant use because of the availability of relevant data. We first estimated future fluorocarbon emissions from the targeted appliances; we next compared those emissions in the units of CO₂ equivalent to the level of CO₂ emissions in 1990 from a quantitative point of view. As the result of this study, it was found that fluorocarbon emissions in 1999 and 2010 would be equal to approximately 7 and 3% of the level of CO₂ emissions in 1990 respectively. Moreover, if we implement a 100% recovery rate in every recovery route, we can reduce a large amount of emissions which correspond to approximately 2–5% of the level of CO₂ emissions in 1990, even if we take into account the energy-related CO₂ emissions by the transportation and decomposition of fluorocarbons.     

JFC磷酸酯的合成和应用

详述了JFC磷酸酯的合成工艺路线，以及它在织物前处理精练工艺中的应用。与其它磷酸酯类精练剂性能对比，证明它可作为一种性能优良的精练剂中的添加剂。