高纯锗探测器的快定时性能及其应用

为了将高纯锗（ＨＰＧｅ）探测器用于快定时的物理实验中，本实验研究厂影响高纯锗探测器定时谱仪时间性能的各种因素，找出了获得谱仪最小时间分辨的各种最佳参数。并建立了分辨时间为４．１９ｎｓ，能量分辨率为２０ｋｅＶ，微分非线性好于±２．０％，计效率可承受１２０×１０￣３ｓ￣（－１）的时间微分扰动角关联谱仪。利用此谱仪，以￣（２０４）Ｂｉ为探针核，研究了Ｂｉ系高温超导的微观机理，取得了较好的结果。     

天然气的储存

随着能源结构的调整,天然气在一次能源中的比重逐步增大,天然气的储存成为人们日益关注的课题,作者就此作一综述。     

钙铁硅铁磁体微晶玻璃热处理制度的研究

使用XRD、DTA、VSM等分析测试手段对在还原气氛下含少量B2O3、P2O5钙铁硅微晶玻璃的热处理制度进行了较深入的研究。研究发展，预核化处理对于钙铁硅微晶玻璃的晶化无明显作用。900℃作为钙铁硅微晶玻璃的晶化温度较适宜，晶化时间宜8h以上。     

RE／S值对控轧低碳Mn－Nb－RE钢硫化物成分和形貌的影响

用扫描电镜测定了含０．０４１％～０．０７６％ＲＥ的低碳Ｍｎ－Ｎｂ－ＲＥ钢中硫化物的成分、大小和形貌。ＲＥ／Ｓ值为２．８～３．０时，钢中的硫化物充分变质。     

专家系统应用于锅炉分气缸的设计和选型

基于专家系统的基本理论 ,根据锅炉分气缸设计、选型的特点和现场的实际条件 ,开发了锅炉分气缸设计、选型专家系统。该系统采用VisualC ++语言编程 ,模块结构 ,图形化用户界面等     

微机模拟处理pH络合滴定法研究——Ⅱ.终点确定方法和最佳实验条件模拟估计程序

本文利用简便的滴定过程模型,确立了微机模拟处理实验数据,方便、准确地求解络合滴定等当点的方法。设计了最佳实验条件模拟估计程序。该法测定Zn~(2+),Pb~(2+),Cu~(2+),Fe~(3+)结果的相对误差Δ<1％。pH=6-7时,测定Ca~(2+)的相对误差为-1.61％;σ<0.001mmol,(N=5)。     

铸造铝合金(ZL109)激光表面处理

采用功率为2kW级CO_2连续可调式横流激光光源,对不同涂层的ZL109试样表面进行了激光熔凝的实验研究。     

Ti 离子注入 LiNbO_3表面光学性能

本文研究了 x,y,z 三种切向的 LiNbO_3单晶片注入350keV 高能 Ti 离子(注入剂量为1.5×10~(17)/cm~2)后的表面光学性能。利用光谱仪及 AUEL 椭偏仪对三种切向 LiNbO_3试样在不同工艺处理后的光透射率及折射率进行了测试。注入损伤造成的光损耗可通过热处理消除,使晶格结构恢复至与完整晶格排列相近;注入层的折射率可增加11—13％左右。     

基于HMM方法的动态手势轨迹训练性能研究

基于HMM(Hidden Markov Model,隐形马尔可夫模型)对动态手势轨迹的训练是手势识别的关键技术之一。本文对HMM的模型训练采用Baum.Welch算法,并分别从迭代次数,样本个数选取,以及模型初值选取等方面对动态手势轨迹的训练性能进行了研究。实验结果表明HMM方法对具有时空特性的动态手势轨迹识别是非常有效的。     

Optimal control and operation of drum granulation processes

Process optimisation and optimal control of batch and continuous drum granulation processes are studied in this paper. The main focus of the current research has been: (i) construction of optimisation and control relevant, population balance models through the incorporation of moisture content, drum rotation rate and bed depth into the coalescence kernels; (ii) investigation of optimal operational conditions using constrained optimisation techniques; (iii) development of optimal control algorithms based on discretized population balance equations; and (iv) comprehensive simulation studies on optimal control of both batch and continuous granulation processes. The objective of steady state optimisation is to minimise the recycle rate with minimum cost for continuous processes. It has been identified that the drum rotation-rate, bed depth (material charge), and moisture content of solids are practical decision (design) parameters for system optimisation. The objective for the optimal control of batch granulation processes is to maximize the mass of product-sized particles with minimum time and binder consumption. The objective for the optimal control of the continuous process is to drive the process from one steady state to another in a minimum time with minimum binder consumption, which is also known as the state-driving problem. It has been known for some time that the binder spray-rate is the most effective control (manipulative) variable. Although other possible manipulative variables, such as feed flow-rate and additional powder flow-rate have been investigated in the complete research project, only the single input problem with the binder spray rate as the manipulative variable is addressed in the paper to demonstrate the methodology. It can be shown from simulation results that the proposed models are suitable for control and optimisation studies, and the optimisation algorithms connected with either steady state or dynamic models are successful for the determination of optimal operational conditions and dynamic trajectories with good convergence properties.