胃肠道激光内镜应用技术

本文结合作者的体验和文献，详细介绍了激光光导纤维检查与准备，激光内镜在胃肠道疾病应用的技巧、方法和注意事项等，可为临床医生和相关技术人员提供帮助。     

CuO/ZnO甲醇合成催化剂的正电子湮没谱学研究

发展了用正电子湮没寿命参数测定用共沉淀方法制备的金属氧化物系固溶度的新方法。测量了一系列用共沉淀方法制备的不同CuO at％含量的CuO/ZnO甲醇合成催化剂粉末(压制成片)还原前后的正电子寿命谱。分析该种催化剂的固溶特性及其与正电子寿命参数的关系,得出还原后样品的固溶度为12CuOat％.支持了CuO/ZnO甲醇合成催化剂以Cu~+离子为活性中心的观点。     

电潜泵中压变频调速系统的改进

电潜泵中压变频器输出端产生高次谐波和脉冲电流 ,对电潜泵电动机的绝缘性能和轴承寿命造成不利影响。为此 ,提出 3项改进对策 :①采用谐振软性开关逆变电路 ,使功率开关器件在零电压条件下导通 ;②在变频器逆变输出端设置电抗滤波器抑制高次谐波电流 ;③改变电动机内部结构 ,如加大定子槽宽 ,增加转子导条尺寸 ,变星接法为星 角接法 ,采用绝缘轴承等。实践证明 ,采取改进对策后 ,不仅提高了电潜泵的产量 ,而且变频器滤波后电动机端的过电压明显减小 ,电潜泵和电缆的寿命延长     

甲基丙烯酸乙酯合成工艺研究

以大孔强酸性离子交换树脂为催化剂,甲基丙烯酸(MAA)与乙醇直接酯化合成甲基丙烯酸乙酯(EMA)。在MAA与乙醇摩尔比为1:3、反应温度89～93℃、空速0.3h~(-1)的条件下,MAA转化率不低于98％,EMA的选择性不低于99％。     

煤层物性测井评价方法初探

依据煤岩的赋存方式和结构特点，利用电阻率和井径测井资料在不同煤质结构的煤层所表现的差异性，建立了2个指标(即深侧向电阻率与微球电阻率之间的比值，井径与钻头之间的比值)对煤质结构进行了准确的识别。用多元回归的概率模型建立了煤岩镜质反射率的测井计算模式，其结果与已有的煤心分析数据对比，两者具有较好的一致性。在综合分析的基础上，对煤层的重要物性参数煤阶、煤质结构进行了测井评价。     

Corrosion Inhibition Mechanism with Spilt Cell Technique of Rare Earth Metal on LC4 Al Alloy

A new method of studying the corrosion inhibition mechanism of rare earth metal(REM) on LC4 Al alloy with the spilt cell technique was studied. The principle and experimental method of the spilt cell technique were analyzed. By measuring the change of net-electric current between the two electrodes caused by the change of the amount of oxygen in the solution and the addition of CeCl₃, the influence of corrosive performance of CeCl₃ on LC4 super-power aluminum alloy in the 0.1 mol·L⁻¹ NaCl solution was investigated. Meanwhile, the conditional changes of pH values, CeCl₃ solution, additire and time of performance were also studied. Finally, the features of electrode surface were revealed by using SEM and X-ray energy-dispersive spectrometry (EDS). By combining these with other electric chemical techniques, such as potential-time curve, polarization curve et al.     

Fabrication of multi-walled carbon nanotube reinforced polyelectrolyte hollow nanofibers by electrospinning

Hybrid hollow multi-walled carbon nanotubes (MWCNTs)/polyelectrolytes (PE) nanofibers were prepared by a combination of the electrospinning method and layer-by-layer (LbL) technique. The mixed polystyrene (PS)/MWCNTs nanofibers were obtained by electrospinning method, which were employed as templates to self-assembly multilayered polyelectrolytes by LbL technique. Hollow MWCNTs/PE nanofibers were obtained by selectively removed part of the template: PS, which is confirmed by Raman spectra, transmission electron microscopy (TEM) and scanning electron microscopy (SEM).     

碳酸盐岩气藏加砂压裂重复改造试验效果分析

针对碳酸盐岩气藏部分气井生产效能低的状况，决定在长庆气田下古生界尝试开展加砂压裂重复改造试验，以期提高低产、低效气井的产量，延长气田稳产期。通过潜心研究、精细设计及现场质检监控，优选了4口老井进行加砂压裂重复改造现场试验。从试验结果来看，虽然只有1口井取得明显的改造效果，但4口井加砂压裂施工都是成功的，说明对碳酸盐岩气藏实施加砂压裂是可以实现的，但在选井思路和压裂工艺方面还有待探索和研究。     

Vibration cavitation behaviour of selected Ni-Mn-Ga alloys

Vibration cavitation erosion tests were carried out on Ni-Mn-Ga alloys of three different crystal structures: (1) the cubic austenite, (2) the non-modulated tetragonal martensite (T) and (3) the five-layered martensite (5M). All Ni-Mn-Ga alloys exhibited cavitation behaviour characterized by a step-wise curve of mass loss versus test time. This behaviour is correlated to the microstructural nature of the alloys as well as the surface conditions of the pre-test samples. The type and concentration of the defects at the surfaces were critical to the cavitation resistance of the alloys. The best cavitation resistant alloy was of a cubic austenitic structure, followed with the alloy of a tetragonal T-martensite. The largest material loss was found in the alloy with a 5M martensite. All the studied Ni-Mn-Ga alloys had an excellent cavitation resistance compared to that of the reference stainless steel, and they even excelled some NiTi alloys found in literature. This may be due to the superelasticity of the cubic austenite and the twinning of the martensitic phases.