Surface leakage currents in SiN/sub x/ passivated AlGaN/GaN HFETs

A novel guarded surface leakage test structure is used to isolate the surface and bulk leakage contributions to gate current in AlGaN/GaN HFETs. Passivation with various recipes of SiN/sub x/ always resulted in the commonly observed increase in gate leakage, which was found to be dominated by bulk leakage through the AlGaN. However, high temperature deposited SiN/sub x/ recipes gave a 1-2 orders reduction in surface leakage, whereas low temperature deposition gave an increase. Gate lag measurements were found to correlate closely with the surface leakage component, giving direct evidence that the key device problem of current slump is associated with current flow at the AlGaN surface.     

Adaptive two-loop Voltage-mode control of DC-DC switching converters

A new two-loop control scheme for voltage-mode control (VMC) of dc-dc switching converters is presented. The proposed method adds a high-gain robust loop with two controllers to the conventional VMC loop, achieving an analog "adaptive" loop in which the "equivalent voltage regulator" varies with the changing power stage parameters given as follows: 1) input voltage; 2) load; and 3) component tolerances. The loop significantly improves the disturbance rejection of the control system, i.e., closed-loop output impedance and audiosusceptibility while preserving the stability and the loop gain crossover frequency to a significant extent. Both the small-signal analysis and the experimental results carried out on a buck converter demonstrate the superiority of the proposed scheme with respect to the conventional single loop.     

Discrete Modeling and Suggested Measurement of Heat Transfer in Gas-Solids Flows

This article presents a two-dimensional transient model for gas-solids flow and heat transfer through pipes using the coupled Computational Fluid Dynamics and Discrete Element Method approach. Numerical simulations have been conducted to examine the modification of fluid thermal structure due to the presence of particles in a pneumatic transport pipeline. Modeled results have demonstrated the key role of transversal motion of rebounding particles in the pipe cross section in altering fluid temperature. Further implementation of this modeling technique in air-drying processes is discussed and possible experimental methods for the measurement of in situ particle and fluid motion and temperature profile are cited.     

Low RF noise and power loss for ion-implanted Si having an improved implantation process

Very-low-transmission line noise of <0.25 dB at 18 GHz and low power loss /spl les/0.6 dB at 110 GHz have been measured on transmission lines fabricated on proton-implanted Si. In contrast, a standard Si substrate gave much higher noise of 2.5 dB and worse power loss of 5 dB. The good RF integrity of proton-implanted Si results from the high isolation impedance to ground, as analyzed by an equivalent circuit model. The proton implantation is also done after forming the transmission lines at a reduced implantation energy of /spl sim/4 MeV. This enables easier process integration into current VLSI technology.     

High-performance surface-micromachined inchworm actuator

This work demonstrates a polycrystalline silicon surface-micromachined inchworm actuator that exhibits high-performance characteristics such as large force (/spl plusmn/0.5 millinewtons), large velocity range (0 to /spl plusmn/4.4 mm/sec), large displacement range (/spl plusmn/100 microns), small step size (/spl plusmn/10, /spl plusmn/40 or /spl plusmn/100 nanometers), low power consumption (nanojoules per cycle), continuous bidirectional operation and relatively small area (600 /spl times/ 200/spl mu/m/sup 2/). An in situ load spring calibrated on a logarithmic scale from micronewtons to millinewtons, optical microscopy and Michelson interferometry are used to characterize its performance. The actuator consists of a force-amplifying plate that spans two voltage-controlled clamps, and walking is achieved by appropriately sequencing signals to these three components. In the clamps, normal force is borne by equipotential rubbing counterfaces, enabling friction to be measured against load. Using different monolayer coatings, we show that the static coefficient of friction can be changed from 0.14 to 1.04, and that it is load-independent over a broad range. We further find that the static coefficient of friction does not accurately predict the force generated by the actuator and attribute this to nanometer-scale presliding tangential deflections.     

Manipulation of microenvironment with a built-in electrochemical actuator in proximity of a dissolved oxygen microsensor

Biochemical sensors for continuous monitoring require dependable periodic self diagnosis with acceptable simplicity to check its functionality during operation. An in-situ self-diagnostic technique for a dissolved oxygen microsensor is proposed in an effort to devise an intelligent microsensor system with an integrated electrochemical actuation electrode. With a built-in platinum microelectrode that surrounds the microsensor, two kinds of microenvironments, called the oxygen-saturated or oxygen-depleted phases, can be created by water electrolysis, depending on the polarity. The functionality of the microsensor can be checked during these microenvironment phases. The polarographic oxygen microsensor is fabricated on a flexible polyimide substrate (Kapton) and the feasibility of the proposed concept is demonstrated in a physiological solution. The sensor responds properly during the oxygen-generating and oxygen-depleting phases. The use of these microenvironments for in-situ self-calibration is discussed to achieve functional integration, as well as structural integration, of the microsensor system.     

QoS enhancement for adaptive streaming services over WCDMA

This paper presents a new method to adapt the quality-of-service (QoS) in a wideband code-division multiple-access (WCDMA) system, called radio network feedback (RNF). The concept of RNF is in general applicable to all the services requiring a minimum quality (i.e., non best effort) and in this paper, the focus is on streaming. In this context, RNF makes it possible for a streaming server to adapt its source bit rate to a WCDMA radio link, whose bandwidth may vary in time due, for example, to decongestion/congestion situations over the air interface or to handover. This is very beneficial for the end user as it allows to increase the bandwidth (i.e., the quality) when possible and to decrease it (instead of just dropping the service) when needed. RNF was compared with Client-based adaptation solutions. Simulation results show that RNF is fast and accurate and performs better than Client-based adaptation. For example, rebuffering occurs only with Client-based method. Moreover, with RNF the up-switch is performed only when needed, whereas the up-switch performed by means of the Client-based method is often erroneous and may annoy the end user.     

Photoswitching of Ferroelectric Liquid Crystals Using Unsymmetrical Chiral Thioindigo Dopants: Photoinduced Inversion of the Sign of Spontaneous Polarization

A new unsymmetrical chiral thioindigo dopant 6‐[(R,R)‐2,3‐difluorooct‐1‐yloxy]‐5′‐nitro‐6′‐[(R)‐2‐octyloxy]thioindigo ( 4 ) designed to photoinvert the sign of spontaneous polarization (P_S) in a ferroelectric chiral smectic C (SmC*) liquid crystal was prepared using a synthetic approach previously developed in our laboratory. In this new “ambidextrous” design, the (R)‐2‐octyloxy side‐chain is sterically coupled to the thioindigo core and induces a positive P_S, whereas the (R,R)‐2,3‐difluorooctyloxy side‐chain is decoupled from the core and induces a larger negative P_S. In the trans form, this dopant induces a negative polarization in the SmC host (+)‐4‐(4‐methylhexyloxy)phenyl 4‐decyloxybenzoate ( PhB ). Irradiation of a 1 mol‐% mixture of 4 in PhB at λ = 510 nm caused a sign inversion of P_S, from –0.88 to +0.42 nC cm^–2 at T – T_C = –5 °C, which is consistent with an increase in the polarization power of the coupled 2‐octyloxy/thioindigo unit over that of the 2,3‐difluorooctyloxy unit, due to the increase in transverse dipole moment of the thioindigo core upon trans–cis photoisomerization. The P_S sign inversion was confirmed by a surface‐stabilized ferroelectric liquid crystal photoswitching experiment. Spectroscopic measurements on films of the doped liquid crystal mixtures showed that trans–cis photoisomerization is gradually suppressed with increasing dopant mole fraction, possibly as a result of increased dopant aggregation.