Mechanical properties of certain oriented crystalline polymers

The yield stress is a simple function of the deformation ratio in the direction of testing for specimens oriented by uniaxial or biaxial stretching or rolling. Unless the yield stress increases more rapidly than in proportion to the deformation ratio, there will be instability during tensile creep under high loads. The relative merit of various polymers differs for creep and stress relaxation. Fatigue and bend recovery are also related to the molecular structure.     

Kinetic analysis of plasma VLDL-TG and VLDL-remnant-TG turnover in anesthetized rats

We have estimated the turnover and relative pool sizes of nascent-VLDL-TG and VLDL-remnants-TG in anesthetized rats. [1-¹⁴C]Palmitoyl- and [2-³H]glyceryl-labeled “VLDL”-TG (including nascent VLDL-TG and VLDL-remnants-TG) were prepared by injecting labeled palmitate and glycerol into donor rats. Labeled serum from these rats was then injected intravenously into nembutalized male rats and serial blood samples taken for 30 min. Special care was taken to define any early components in the labeled “VLDL”-TG disappearance curves. In other experiments, the donors were rendered functionally hepatectomized 30 min after injection of³H-glycerol and the endogenous labeled VLDL-TG was allowed to circulate 30–60 min before collection of the TG-labeled VLDL-remnants-containing serum. The latter was injected into 4 recipient nembutalized rats and the remnant-TG-turnover measured by serial sampling as above. In two cases,¹⁴C-“VLDL” and³H-VLDL-remnants were injected as a single bolus into ether-anesthetized rats. Despite its complex composition, “VLDL”-TG in most cases disappeared in a single exponential fashion for 30 min with an average half-life of 5.9 min in nembutalized and 2.8 in ether-anesthetized rats. VLDL-remnants-TG showed a more complex behavior, but contained a major rapid component with a mean t_1/2 of ca. 1.5 min in both groups. The data, analyzed by multicompartmental analysis, were fitted to a simple model in which turnover of a larger nascent VLDL-TG pool with formation of a more rapidly turning over smaller pool of VLDL-remnant-TG is the rate-limiting step in overall TG removal from the d<1.006 fraction of rat serum. The data are consistent with our theoretical prediction that under these conditions the kinetics of the VLDL-remnants cannot be resolved from analysis of the total composite “VLDL” (nascent plus remnant) pool.     

Non-Isothermal crystallization of isotactic polypropylene in dotriacontane. I: Effects of dilution,cooling rate,and nucleating agent addition on overall crystallization kinetics

The overall non-isothermal crystallization kinetics for nucleated and non-nucleated isotactic polypropylene (iPP) in dotriacontane systems was investigated. Adipic acid was used as the nucleating agent. Crystallization peak temperature was determined via differential scanning calorimetry as a function of the experimentally controlled variables iPP concentration, cooling rate, and nucleating agent concentration. The influence of these variables on crystallization mechanism and spherulitic structure as implied by the Ozawa and Ziabicki analyses was determined. The non-isothermal crystallization kinetics presented here are the first for iPP-diluent systems with and without nucleating agent.     

Inactivation of Giardia muris Using Ozone and Ozone-Hydrogen Peroxide

The disinfection effects of the ozone molecule alone and that of ozone decomposition products when inactivating Giardia muris cysts were investigated at bench-scale using two different ozone demand-free laboratory buffer systems. The first water was a 0.05 M phosphate buffer with hydrogen peroxide added at a 10:1 weight ratio. The second water was a 0.05 M phosphate – 0.01 M bicarbonate buffer which quickly scavenged radical species from ozone decomposition. The C3H/HeN mouse model was used to assess the infectivity of ozone treated cysts.

The phosphate-bicarbonate buffer system had significantly greater (P ≤ 0.05) inactivation of G. muris cysts than that observed in the phosphate buffer – peroxide system where ozone was completely decomposed in less than 120 s. Consequently, the design of ozone disinfection processes should maintain ozone residual for disinfection prior to the addition of hydrogen peroxide for the oxidation of other compounds.     

Polymer modification and synthesis using sulphenyl derivatives: 9. Addition of alkylsulphenyl chlorides to cis-1, 4-polybutadiene

Methanesulphenyl chloride and n-butanesulphenyl chloride add readily across the double bonds in cis-1,4-polybutadiene. The addition is highly regioselective so that long sequences of saturated units are formed. The products are very unstable, evolving hydrogen chloride on standing, but can be stabilized by replacing the labile chlorine atom with other nucleophiles in a phase transfer catalysed reaction.     

Sub-ambient cold-start emissions reduction using SwRI® PO x catalyst technology

This paper describes the application of SwRI’s cold-start PO _x catalyst technology to reduce cold-start hydrocarbon emissions from a US Tier 2 vehicle at −7 °C. A reduction in −7 °C (20 °F) cold-start hydrocarbons will help US Tier 2 vehicles meet the proposed EPA NMOG standards. Improvements in cold temperature hydrocarbon emissions would also be beneficial in many parts of Europe during the winter months. In this work, a total hydrocarbon reduction of 19% was realized at 24 °C, in line with previous results, but only up to 3% at −7 °C. Insufficient oxygen in the engine-out exhaust gas at −7 °C was determined to be the reason why the PO _x catalyst failed to significantly reduce HC emissions. Addition of supplemental oxygen to the exhaust during the cold-start, to simulate an adjustment in the engine calibration to less rich operation, resulted in a total hydrocarbon reduction of 18% with the PO _x catalysts in place, but no benefit when the PO _x catalysts were removed. Hence, the PO _x catalyst approach can be used to good effect, even under sub-ambient cold-start conditions.     

Feeding response of Ips paraconfusus to phloem and phloem metabolites of Heterobasidion annosum-inoculated ponderosa pine,Pinus ponderosa

In studies of feeding by the bark beetle, Ips paraconfusus, two pine stilbenes (pinosylvin and pinosylvin methyl ether), ferulic acid glucoside, and enantiomers of the four most common sugars present in ponderosa pine phloem (sucrose, glucose, fructose, and raffinose) did not stimulate or reduce male feeding when assayed on wet -cellulose with or without stimulatory phloem extractives present. When allowed to feed on wet -cellulose containing sequential extracts (hexane, methanol, and water) of ponderosa pine phloem, methanol and water extractives stimulated feeding, but hexane extractives did not. Males confined in wet -cellulose containing aqueous or organic extracts of culture broths derived from phloem tissue and containing the root pathogen, Heterobasidion annosum, ingested less substrate than beetles confined to control preparations. In an assay using logs from uninoculated ponderosa pines, the mean lengths of phloem in the digestive tracts increased as time spent feeding increased. Males confined to the phloem of basal logs cut from ponderosa pines artificially inoculated with H. annosum ingested significantly less phloem than beetles in logs cut from trees that were (combined) mock-inoculated or uninoculated and did not contain the pathogen. However, individual pathogen-containing treatments were not significantly different from uninoculated controls. It was concluded that altered feeding rates are not a major factor which may explain why diseased ponderosa pines are colonized by I. paraconfusus.     

EVAPORATION FROM POROUS MEDIA: A CAPILLARY MODEL OF A PENETRATING FRONT

A capillary tube model was solved to investigate the influence of mass transfer coefficient, temperature, and front depth on the evaporation rate during the penetrating-front period of water-filled porous media dried in hot air. The results show that increasing the flow rate of the drying air is not so efficient as increasing the sample temperature. Due to attenuating diffusion rate, the rate of liquid front migration decreases with time. The calculations explain the falling rate period behavior of sandstone heated at 121°C. Trends depicted by the model may be useful for the design of heating conditions for drying processes.     

Non-Isothermal crystallization of isotactic polypropylene in dotriacontane. II: Effects of dilution,cooling rate,and nucleating agent addition on growth rate

Non-isothermal crystallization growth rates of nucleated and non-nucleated isotactic polypropylene (iPP) in dotriacontane were determined experimentally by thermal optical microscopy. Adipic acid was used as the nucleating agent. The non-isothermal growth rates of the nucleated and non-nucleated systems were compared with experimentally determined isothermal growth rates. The Lauritzen and Hoffman growth rate equation, originally developed for isothermal crystallization, was modified to describe the non-isothermal growth. The modified Lauritzen-Hoffman equation was used to predict isothermal growth rates from non-isothermal crystallization for the nucleated and non-nucleated polymer-diluent mixtures. This study is the first to deal with polymer-diluent-nucleating agent systems vital to membrane production.     

Compatibilization of polymer blends from poly(styrene‐co‐acrylonitrile) and polycarbonate by oxazoline modification of poly(styrene‐co‐acrylonitrile) in the melt

A good way of achieving compatibility in polymer blends of poly(styrene‐co‐acrylonitrile) (S/AN) and bisphenol A polycarbonate (PC) is the chemical modification of S/AN in the melt. A catalyzed reaction of the nitrile groups with a substituted 2‐amino alcohol or 2‐amino phenol resulted in a conversion of nitrile groups of 55–75% in 60 min. The introduced heterocyclic structures were ethyl hydroxymethyl oxazoline (EHMOXA) and benzoxazole (BenzOXA), respectively. The use of dibutyltin oxide as a catalyst led to the highest efficiency. The modified polymer was characterized by Fourier transform infrared and NMR spectroscopy, elemental analysis, and reactions with organic acids and anhydrides. The modified S/AN showed good technical compatibility (single glass‐transition temperature) with PC in blends made from solution and from the melt. All blends were characterized with oscillating rheometry and differential scanning calorimetry. Rheological measurements showed that EHMOXA–S/AN reacted with PC and had crosslinked structures, whereas BenzOXA–S/AN showed compatibilization without any (crosslinking) reaction. The melt blends of BenzOXA–S/AN and PC showed a downward shift in the complex viscosity due to the influence of the BenzOXA group. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2322–2332, 2003