Surface chemical heterogeneity of bacteriogenic iron oxides from a subterranean environment

This study quantifies the surface chemical heterogeneity of bacteriogenic iron oxides (BIOS) and its end-members (2-line ferrihydrite and intermixed intact and fragmented bacteria). On a dry weight basis, BIOS consisted of 64.5 +/- 1.8% ferrihydrite and 34.5 +/- 1.8% organic matter. Enrichment of Al, Cu, Cr, Mn, Sr, and Zn was shown in the solid versus the aqueous phase (1.9 < log Kd < 4.2). Within the solid-phase Al (69.5%), Cu (78.7%), and Zn (77.9%) were associated with the bacteria, whereas Cr (59.8%), Mn (99.8%), and Sr (79.4%) preferred ferrihydrite. Acid-base titration data from the BIOS and bacteria were fitted using FOCUS pKa spectroscopy. The bacteria spectrum with pKa's of 4.18 +/- 0.37, 4.80 +/- 0.54, 6.98 +/- 0.45, and 9.75 +/- 0.68 was similar to discrete and continuous spectra for intact and fragmented bacteria. The BIOS spectrum recorded pKa's of 4.27 +/- 0.51, 6.61 +/- 0.51, 7.89 +/- 1.10, and 9.65 +/- 0.66 and was deconvoluted to remove overlapping binding site contributions from the bacteria. The resulting residual iron oxide spectrum coincided with discrete MUSIC spectra for goethite and lepidocrocite with pKa values of 4.10 +/- 0.43, 6.53 +/- 0.45, 7.81 +/- 0.76, and 9.51 +/- 0.68. Surface site density analysis showed that acidic sites (pKa < 6) were contributed by the bacteria (37%), whereas neutral sites (6 < pKa < 8) were characteristic of the iron oxide fraction (35%). Basic sites (8 < pKa) were higher in the bacteria (57%), than in the BIOS (44%) or iron oxide fractions (47%). This analysis suggested a high degree of bacterial group masking and a similarity between the BIOS and goethite surface reactivity. An understanding of the BIOS surface chemical heterogeneity and inherent proton and metal binding capacity was obtained through the use of FOCUS apparent pKa spectroscopy.     

Early postmortem electrical stimulation simulates PSE pork development

Carcasses from 64 gilts were subjected to electrical stimulation (ES) at 3, 15, 25, 35, 45, and 55 min postmortem or were untreated (NS). Temperature and pH of longissimus muscles were recorded at 1, 7, 14, 20, 30, 40, 50, and 60 min, and 24 h postmortem. Muscle samples were collected at 1, 30 and 60 min, and 24 h for determining glycolytic metabolite concentrations. ES at 3, 15, and 25 min resulted in lower (P<0.05) muscle pH, but stimulation after 25 min had no effect on muscle pH. Likewise, ES prior to 25 min resulted in greater (P<0.05) muscle temperatures. Muscle lactate concentrations were greater (P<0.05) in carcasses stimulated before 45 min postmortem. Glucose 6-phosphate concentration decreased (P<0.05) during the first hr postmortem and increased (P<0.05) thereafter. ES of carcasses at 45 and 55 min resulted in higher (P<0.05) concentrations of muscle glucose 6-phosphate at 24 h compared with NS and early-stimulated carcasses. Muscle glycogen concentrations at 30 min in carcasses stimulated at 3, 15 and 25 min were lower (P<0.05) than NS carcasses. Carcasses stimulated at 3 and 15 min exhibited lower (P<0.05) concentrations of muscle glycogen at 60 min than NS carcasses. Carcasses stimulated at 3 and 15 min postmortem exhibited lower (P<0.05) color and firmness scores, while ES at 3 and 25 min postmortem resulted in lower (P<0.05) water holding capacity. ES had no significant effect on CIE L(?), a(?), b(?), or 24 h muscle pH. These data show that ES of pork carcasses during the first 25 min postmortem creates PSE-like quality characteristics and suggest that ES is a potential model for studying pork quality development.     

A Review of the U.S. Department of Energy's Inertial Fusion Energy Program

This is the final report of a panel set up by the U.S. Department of Energy (DOE) Fusion Energy Sciences Advisory Committee (FESAC) in response to a charge letter from Dr. Ray Orbach (Appendix A). In that letter, Dr. Orbach asked FESAC for an assessment of the present status of inertial fusion energy (IFE) research carried out in contributing programs. These programs include the heavy ion (HI) beam, the high average power laser (HAPL), and Z-Pinch drivers and associated technologies, including fast ignition (FI). This report, presented to FESAC on March 29, 2004, and subsequently approved by them (Appendix B), presents FESAC's response to that charge.     

Synthesis of an ammonium ionophore and its application in a planar ion-selective electrode

A modular technique was used to synthesize an ammonium-selective ionophore based on a cyclic depsipeptide structure. The ionophore was incorporated into a planar ion-selective electrode sensor format and the selectivity tested versus a range of metal cations in a commercial clinical diagnostic "point-of-care" instrument. Four sensor membrane formulations were tested, all of which consisted of plasticized PVC. Formulations differed as to the type of plasticizer used and whether an ionic additive was present. It was found that the membrane containing the polar plasticizer nitrophenyl octyl ether in the absence of ionic additive exhibited near-Nernstian behavior (slope, 60.1 mV/decade at 37 degrees C) and possessed high selectivity for ammonium ion over lithium and the divalent cations, calcium and magnesium (log K(POT)NH4+(j) = -7.3, -4.4, and -7.1 for lithium, calcium, and magnesium ions, respectively). The same membrane also exhibited sodium and potassium selectivity that was comparable to that reported for nonactin (log K(POT)NH4+(j) = -2.1 and -0.6 for sodium and potassium, respectively, compared to -2.4 and -0.9 in the case of nonactin). Membranes containing the less polar plasticizer, dioctyl phthalate, showed sub-Nernstian behavior (slope, <50 mV/decade at 37 degrees C). In all cases, the presence of the ionic additive potassium tetrakis(4-chlorophenyl)borate substantially reduced the selectivity observed. The flexible modular synthetic technique developed and reported here will allow the cyclic depsipeptide structure to be tuned for optimum selectivity.     

A Common Medium for Programming Operations-Research Models

Operations research is an interdisciplinary science that develops scientific methods for modeling and solving decision-making problems. Arguably, the two most established and commonly practiced OR methodologies are mathematical programming (also called optimization) and discrete-event system simulation (called simulation). Mathematical programming describes a decision problem as decision variables and as mathematical functions of variables that capture the objective and problem constraints. For dynamic systems that are too complex to allow exact, closed-form solutions in continuous time, simulation can identify and describe events of interest and model their occurrences at discrete points in time. Python can glue together independent software environments to improve the software development cycle for sophisticated operations-research applications, which integrate different modeling methodologies.     

Intracranial self-stimulation of the dorsal raphe sensitizes psychostimulant locomotion.

The authors hypothesized that repeated rewarding electrical stimulation of the dorsal raphe can produce behavioral sensitization to psychostimulants. Groups of male rats were implanted with a stimulation electrode and preexposed to brain stimulation at parameters set to equate rewarding effectiveness across rats. Control groups were implanted with an electrode but never stimulated, or not implanted at all. Twenty-four hours after the 12th self-stimulation session, all groups were challenged with amphetamine (0.5 mg/kg, ip), nicotine (0.2 mg/kg, sc), or saline, and locomotor activity was measured for 1 hr. Locomotor responses to amphetamine and to nicotine were significantly greater in rats preexposed to brain stimulation. These findings suggest at least partial overlap of underlying substrates. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

A review of machining theory and tool wear with a view to developing micro and nano machining processes

This paper reviews the current state-of-the-art surrounding macro scale machining; it discusses how these factors will influence the future development of micro and nano scale machining. The paper begins by reviewing machining theory, and then discusses high speed machining, tool wear, tool coatings, micromachining, meso machine tool design and future applications and research directions. Tool wear is a factor that determines the economy of the machining process. Therefore, an extensive part of the paper is devoted to the development of materials used to coat tools; in turn, it is anticipated these coatings will used in future micro machining applications. Consideration is also given to machine structures that are required to use these cutting tools at speeds in excess of one million revolutions per minute. This review provides a timely explanation of the literature surrounding the factors required for successful micro and nano machining.     

Liquid Crystal Tunable mm Wave Frequency Selective Surface

A frequency selective surface (FSS) which exploits the dielectric anisotropy of liquid crystals to generate an electronically tunable bandpass filter response at D Band (110-170 GHz) is presented. The device consists of two printed arrays of slot elements which are separated by a 130-mum thick layer of liquid crystals. A 3% shift in the filter passband occurs when the substrate permittivity is increased by applying a control signal of 10 V. Measured results show that the insertion loss increases from -3.7 dB to -10.4 dB at resonance (134 GHz), thus demonstrating the potential to create a FSS which can be switched between a transmitting and a reflecting structure.     

Polarisation independent bandpass FSS

The spectral transmittance of a frequency selective surface (FSS), which consists of two free-standing arrays of short-circuited nested annular slots, is presented. The FSS was designed to provide a minimum of 20 dB isolation between the frequency bands 316.5-325.5 and 349.5-358.5 GHz when the filter operates in the TE and TM planes at 45deg incidence. Experimental results, which are in close agreement with the computed transmission coefficients, show that the maximum insertion loss is 0.9 dB, and the minimum cross-polar discrimination is at least 21 dB in the passbands. The FSS yields virtually identical spectral responses in the two polarisation planes over the frequency range 315-359 GHz.