Microstructural and mechanical property changes with aging of Mo-41Re and Mo-47.5Re alloys

The changes in microstructure and mechanical properties of Mo-41Re and Mo-47.5Re alloys were investigated following 1100 h thermal aging at 1098, 1248 and 1398 K. The electrical resistivity, hardness and tensile properties of the alloys were measured both before and after aging, along with the alloy microstructures though investigation by optical and electron microscopy techniques. The Mo-41Re alloy retained a single-phase solid solution microstructure following 1100 h aging at all temperatures, exhibiting no signs of precipitation, despite measurable changes in resistivity and hardness in the 1098 K aged material. Annealing Mo-47.5Re for 1 h at 1773 K resulted in a two-phase αMo + σ structure, with subsequent aging at 1398 K producing a further precipitation of the σ phase along the grain boundaries. This resulted in increases in resistivity, hardness and tensile strength with a corresponding reduction in ductility. Aging Mo-47.5Re at 1098 and 1248 K led to the development of the χ phase along grain boundaries, resulting in decreased resistivity and increased hardness and tensile strength while showing no loss in ductility relative to the as-annealed material.     

Influence of growth phase on bacterial deposition: interaction mechanisms in packed-bed column and radial stagnation point flow systems

The influence of bacterial growth stage on cell deposition kinetics has been examined using a mutant of Escherichia coli K12. Two experimental techniques--a packed-bed column and a radial stagnation point flow (RSPF) system--were employed to determine bacterial deposition rates onto quartz surfaces over a wide range of solution ionic strengths. Stationary-phase cells were found to be more adhesive than mid-exponential phase cells in both experimental systems. The divergence in deposition behavior was notably more pronounced in the RSPF than in the packed-bed system. For instance, in the RSPF system, the deposition rate of the stationary-phase cells at 0.03 M ionic strength was 14 times greater than that of the mid-exponential cells. The divergence in the packed-bed system was most significant at 0.01 M, where the deposition rate for the stationary-phase cells was nearly 4 times greater than for the mid-exponential cells. To explain the observed adhesion behavior, the stationary and mid-exponential bacterial cells were characterized for their size, surface charge density, electrophoretic mobility, viability, and hydrophobicity. On the basis of this analysis, it is suggested that the stationary cells have a more heterogeneous distribution of charged functional groups on the bacterial surface than the mid-exponential cells, which results in higher deposition kinetics. Furthermore, because the RSPF system enumerates only bacterial cells retained in primary minima, whereas the packed column captures mostly cells deposited in secondary minima, the difference in the stationary and mid-exponential cell deposition kinetics is much more pronounced in the RSPF system.     

Small Classes in the Early Grades, Academic Achievement, and Graduating From High School.

This investigation addressed 3 questions about the long-term effects of early school experiences: (a) Is participation in small classes in the early grades (K-3) related to high school graduation? (b) Is academic achievement in K-3 related to high school graduation? (c) If class size is related to graduation, is the relationship explained by the effect of participation in small classes on students' academic achievement? The study included 4,948 participants in Tennessee's class-size experiment, Project STAR. Analyses showed that graduating was related to K-3 achievement and that attending small classes for 3 or more years increased the likelihood of graduating from high school, especially among students eligible for free lunch. Policy and research implications are discussed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Pathophysiology and Emerging Molecular Therapeutic Targets in Heterotopic Ossification

The term heterotopic ossification (HO) describes bone formation in tissues where bone is normally not present. Musculoskeletal trauma induces signalling events that in turn trigger cells, probably of mesenchymal origin, to differentiate into bone. The aetiology of HO includes extremely rare but severe, generalised and fatal monogenic forms of the disease; and as a common complex disorder in response to musculoskeletal, neurological or burn trauma. The resulting bone forms through a combination of endochondral and intramembranous ossification, depending on the aetiology, initiating stimulus and affected tissue. Given the heterogeneity of the disease, many cell types and biological pathways have been studied in efforts to find effective therapeutic strategies for the disorder. Cells of mesenchymal, haematopoietic and neuroectodermal lineages have all been implicated in the pathogenesis of HO, and the emerging dominant signalling pathways are thought to occur through the bone morphogenetic proteins (BMP), mammalian target of rapamycin (mTOR), and retinoic acid receptor pathways. Increased understanding of these disease mechanisms has resulted in the emergence of several novel investigational therapeutic avenues, including palovarotene and other retinoic acid receptor agonists and activin A inhibitors that target both canonical and non-canonical signalling downstream of the BMP type 1 receptor. In this article we aim to illustrate the key cellular and molecular mechanisms involved in the pathogenesis of HO and outline recent advances in emerging molecular therapies to treat and prevent HO that have had early success in the monogenic disease and are currently being explored in the common complex forms of HO.     

Optimization of soy-biodiesel combustion in a modern diesel engine

As global petroleum demand continues to increase, alternative fuel vehicles are becoming the focus of increasing attention. Biodiesel has emerged as an attractive alternative fuel option due to its domestic availability from renewable sources, its relative physical and chemical similarities to conventional diesel fuel, and its miscibility with conventional diesel. Biodiesel combustion in modern diesel engines does, however, generally result in higher fuel consumption and nitrogen oxide (NO_x) emissions compared to diesel combustion due to fuel property differences including calorific value and oxygen content. The purpose of this study is to determine the optimal engine decision-making for 100% soy-based biodiesel to accommodate fuel property differences via modulation of air-fuel ratio (AFR), exhaust gas recirculation (EGR) fraction, fuel rail pressure, and start of main fuel injection pulse at over 150 different random combinations, each at four very different operating locations. Applying the nominal diesel settings to biodiesel combustion resulted in increases in NO_x at three of the four locations (up to 44%) and fuel consumption (11-20%) over the nominal diesel levels accompanied by substantial reductions in particulate matter (over 80%). The biodiesel optimal settings were defined as the parameter settings that produced comparable or lower NO_x, particulate matter (PM), and peak rate of change of in-cylinder pressure (peak dP/dt, a metric for noise) with respect to nominal diesel levels, while minimizing brake specific fuel consumption (BSFC). At most of the operating locations, the optimal engine decision-making was clearly shifted to lower AFRs and higher EGR fractions in order to reduce the observed increases in NO_x at the nominal settings, and to more advanced timings in order to mitigate the observed increases in fuel consumption at the nominal settings. These optimal parameter combinations for biodiesel were able to reduce NO_x and noise levels below nominal diesel levels while largely maintaining the substantial PM reductions. These parameter combinations, however, had little (maximum 4% reduction) or no net impact on reducing the biodiesel fuel consumption penalty.     

Placement of reference electrode in solid electrolyte cells

The placement of reference electrodes in solid state ionic conductors is not as flexible as in liquid state electrochemistry. This is in particular a problem when material from the gas phase is involved, as in solid oxide fuel cell. Many of the arrangements used are problematic: either they produce results that are very sensitive to electrode placement, change the potential distribution, do not provide a uniform current density and overpotential at the electrode or require delicate patterns liable to fail. We here present a new approach suitable for thin layer SOFC. It includes a calibration procedure derived from numerical simulations in combination with experiments. This allows the use of the common three-electrode arrangement on thin solid electrolyte (SEs) where the reference electrode is placed side by side with the working electrode, on an extension of the thin layer SE. This is so despite the sensitivity of that arrangement to both misalignment of the electrodes and to a difference in the impedance of the two current carrying electrodes. The misalignment tolerated, with the present method, may exceed the SE thickness. The allowed misalignment increases with the electrode/SE impedance ratio. The method copes also with the difference in the electrode impedance. Two special configurations are discussed in which the calibration is not required. However, these require a more accurate preparation technique of the cell.     

Effects of 3‐D microwell culture on initial fate specification in human embryonic stem cells

Several studies have demonstrated that three‐dimensional (3‐D) culture systems influence human embryonic stem cell (hESC) phenotypes and fate choices. However, the effect that these microenvironmental changes have on signaling pathways governing hESC behaviors is not well understood. Here, a 3‐D microwell array was used to investigate differences in activation of developmental pathways between 2‐D and 3‐D cultures of both undifferentiated hESCs and hESCs undergoing initial differentiation in embryoid bodies (EBs). An increased induction into mesoderm and endoderm and differences in expression of genes from multiple signaling pathways that regulate development, including Wnt/β‐catenin, TGF‐β superfamily, Notch, and FGF during EB‐mediated differentiation were observed in 3‐D microwells as compared with the 2‐D substrates. In undifferentiated hESCs, differences in epithelial‐mesenchymal transition phenotypes and the TGFβ/BMP pathway between cultures in 3‐D and 2‐D were also observed. These results illustrate that 3‐D culture influences multiple pathways that may regulate the differentiation trajectories of hESCs. © 2014 American Institute of Chemical Engineers AIChE J, 60: 1225–1235, 2014     

The effect of a polypropylene skin on the structure and properties of PE/PP dual layer pressure pipe

A new and growing family of polyethylene (PE)‐based pressure pipes have a polypropylene (PP) skin. The effect of the PP skin on the structure and properties of the core PE pipe was investigated by comparing the skinned pipe with an uncoated pipe made from the same PE material and with the same dimensions. The annealing effect introduced by the skin changed the PE core pipe density profile across the wall thickness, increasing density in the PE core pipe near to its outer surface. The density at the bore of the coated and the uncoated pipe was similar. The melting temperature and enthalpy of melting data from DSC agreed with the density profile results. The melting temperature of PE core pipe material close to the PP skin increased with increasing skin thickness. Residual stress assessment indicated that, as the PP skin thickness increased, the PE core pipe had a lower level of overall residual stress in the hoop direction. Long‐term hydrostatic strength (LTHS) tests were carried out and showed a higher strength for the coated pipe than the uncoated one. The observed structural changes have been used to explain the relative strength of these two PE pipes. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers