A 0.9 V 92 dB Double-Sampled Switched-RC Delta-Sigma Audio ADC

A 0.9 V third-order double-sampled delta-sigma audio ADC is presented. A new method using a combination of a switched-RC technique and a floating switched-capacitor double-sampling configuration enabled low-voltage operation without clock boosting or bootstrapping. A three-level quantizer with simple dynamic element matching was used to improve linearity. The prototype IC implemented in a 0.13 CMOS process achieves 92 dB DR, 91 dB SNR and 89 dB SNDR in a 24 kHz audio signal bandwidth, while consuming 1.5 mW from a 0.9 V supply. The prototype operates from 0.65 V to 1.5 V supply with minimal performance degradation.     

Prony-Based Optimal Bayes Fault Classification of Overcurrent Protection

The development of deregulation and demand for high-quality electrical energy has lead to a new requirement in different fields of power systems. In the protection field, this means that high sensitivity and fast operation during the fault are required while maltripping of relay protection is not acceptable. One case that may lead to a maltrip of the high-sensitive overcurrent relay is the starting current of the induction motor or inrush current of the transformer. This transient current has the potential to affect the correct operation of protection relays close to the component being switched. In the case of switching events, such transients must not lead to overcurrent relay operation; therefore, a reliable and secure relay response becomes a critical matter. Meanwhile, proper techniques must be used to prevent maltripping of such relays, due to transient currents in the network. In this paper, the optimal Bayes classifier is utilized to develop a method for discriminating the fault from nonfault events. The proposed method has been designed based on extracting the modal parameters of the current waveform using the Prony method. By feeding the fundamental frequency damping and ratio of the 2nd harmonic amplitude over the fundamental harmonic amplitude to the classifier, the fault case is discriminated from the switching case. The suitable performance of this algorithm is demonstrated by simulation of different faults and switching conditions on a power system using PSCAD/EMTDC software.     

Selective Transport of Bismuth Ions through Supported Liquid Membrane

A new supported liquid membrane (SLM) system was prepared for the selective transport of bismuth ions from the aqueous feed into the aqueous permeate phase. The support of the SLM was a thin porous polypropylene or polyvinylidene fluoride membrane impregnated with diisooctyldithiophosphinic acid (Cyanex 301) as mobile carrier in 4‐chloroacetophenon as organic solvent. Cyanex 301 acts as a highly selective carrier for the uphill transport of bismuth ions through the SLM. In the presence of HNO₃ as a metal ion acceptor in the strip solution, the transport of bismuth ions into the strip side reached 70 % of the initial feed concentration after 3.5 hours. The selectivity and efficiency of bismuth transport from aqueous solutions containing different mixtures of cations were investigated. In the presence of P₂O₇^2– ions as suitable masking agent in the feed solution, the interfering effects of other cations were completely eliminated. The selective transport of bismuth through SLM is superior to liquid‐liquid extraction or through bulk liquid membranes. This is due to the high efficiency. The SLM reduces the solvent requirements, combines extraction and stripping operations in a single process and allows the use of highly selective extractants. The system may be applied to samples containing very low bismuth concentrations.     

Gasification of Biogenic Solid Fuels

As a result of shrinking fossil fuels, biomass as a regenerative energy source gains importance. To realize biomass projects it is essential to investigate in convenient thermal procedures. On this evidence an analysis and evaluation of diverse gasification technologies with different boundary conditions and diverse biomasses are indispensable. Form and kind of the biomass as well as the type of the gasification plant cause different compositions of the product gas. The gasifiers show advantages and disadvantages concerning the biomass and the produced gas quality, depending on reactor type, kind of heat supply, gasification medium, and the pressure ratio in the reactor. As the ideal gasifier for different biomass is presently not available, it will be shown, which biomass is suitable for fixed bed or fluidized bed gasifiers.     

Poly(butylene terephthalate)–clay nanocomposites prepared by melt intercalation: morphology and thermomechanical properties

Nanocomposites based on poly(butylene terephthalate) (PBT) and an organoclay (Cloisite 30B) were prepared by melt blending using a twin‐screw extruder. Two kinds of PBTs, ie PBT‐A and PBT‐B, with different inherent viscosities (η_inh), were used for this study (η_inh of PBT‐A and PBT‐B were 0.74 and 1.48, respectively). Dispersion of the clay layers in the PBT nanocomposites was characterized by using X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Tensile and dynamic mechanical properties and non‐isothermal crystallization temperatures of the nanocomposites were also examined. Nanocomposites based on the higher‐viscosity PBT (PBT‐B) showed a higher degree of exfoliation of the clay and a higher reinforcing effect when compared to the composites based on the lower‐viscosity PBT (PBT‐A). The clay nanolayers dispersed in PBT matrices lead to increases in the non‐isothermal crystallization temperatures of the PBTs, with such increases being more significant for the PBT‐B nanocomposites than for the PBT‐A nanoocomposites. Copyright © 2004 Society of Chemical Industry     

Phase behavior of ternary blends containing dimethylpolycarbonate,tetramethylpolycarbonate and poly[styrene‐co‐(methyl methacrylate)] copolymers (or polystyrene)

The miscibility and phase behavior of ternary blends containing dimethylpolycarbonate (DMPC), tetramethylpolycarbonate (TMPC) and poly[styrene‐co‐(methyl methacrylate)] copolymer (SMMA) have been explored. Ternary blends containing polystyrene (PS) instead of SMMA were also examined. Blends of DMPC with SMMA copolymers (or PS) did not form miscible blends regardless of methyl methacrylate (MMA) content in copolymers. However, DMPC blends with SMMA (or PS) blends become miscible by adding TMPC. The miscible region of ternary blends is compared with the previously determined miscibility region of binary blends having the same chemical components and compositions. The region where the ternary blends are miscible is much narrower than that of binary blends. Based on lattice fluid theory, the observed phase behavior of ternary blends was analyzed. Even though the term representing the Gibbs free energy change of mixing for certain ternary blends had a negative value, blends were immiscible. It was revealed that a negative value of the Gibbs free energy change of mixing was not a sufficient condition for miscible ternary blends because of the asymmetry in the binary interactions involved in ternary blends. Copyright © 2004 Society of Chemical Industry     

Holographic polymer‐dispersed liquid crystal fabrication under electric field

The transmission mode of holographic polymer‐dispersed liquid crystals (HPDLCs) was developed an under electric field. It is reported that orientation of LC molecules under an electric field induces orientation of oligomer molecules giving rise to low off‐state diffraction and small grating shrinkage. Copyright © 2005 Society of Chemical Industry     

Poly(Styrene‐Divinylbenzene) Based Media for Liquid Chromatography

The latest developments and in particular important synthetic aspects for the preparation of modern poly(styrene‐divinylbenzene) (PS‐DVB) based liquid chromatography (LC) supports are reviewed. In this context, the chemistry of particular porous and nonporous, functionalized, monolithic, coated silica and more specialized mixed organic PS‐DVB media is covered. Special consideration is given to modern approaches such as micro‐(μ)‐HPLC and coating techniques and their most important applications. Synthetic particularities relevant to the corresponding applications are outlined.     

Alphorn: a remote procedure call environment for fault-tolerant,heterogeneous, distributed systems

Alphorn, a software environment for programming distributed computer systems, is described. Programs running on different computers, possibly of different types and running different operating systems, communicate in a client-server relationship by means of remote procedure calls. This efficient construct structures programs neatly. The paper covers distributed process control, Alphorn's object-based programming style, remote procedure calls, the service interface language, configuration, runtime and debugging, and fault tolerance support