Microchemical Engineering: Components,Plant Concepts User Acceptance – Part I

Over the last five years, many activities have focused on the unexploited field of carrying out reactions on small scales. Due to the rapid development of new components, this paper deals with recent developments only in a compressed form. An important point is the analysis of possible plant concepts for microreactors and whether these are a sensible option. Due to the enormous difference in size between the microchannels and the fluid periphera of possible components this is not just a technical question. It touches on the microtechnology concept as a whole. The direction in which the field should be developed and which measures can be taken to influence its development are questions that are addressed here with respect to the big industrial interest in microreactors.     

Changes in the gaseous H2S barrier properties of damaged silicate coated nylon 6 films

The damage imposed on SiO _x deposited nylon 6 films as a result of abrasion with a cotton cloth and Gelboflex testing was examined by evaluating the rate at which copper plates, which were enveloped by the damaged films, were corroded by H₂S. Abrasion with a cotton cloth caused some micro-cracking of the SiO _x layer and the permeation rate of H₂S approached that of the uncoated nylon 6 film. Damage to the SiO _x layer by twisting and crushing progressed gradually with the number of Gelboflex test cycles and correspondingly the corrosion rate of the copper plates increased. Comparison of the corrosion rates of the copper plates kept in the pouches made of various commercial films with those obtained for the damaged SiO _x deposited nylon 6 films showed a clear relationship between the H₂ permeation rate of the films and the corrosion rate of the copper plates by H₂S.     

Evanescently coupled photodiodes integrating a double-stage taper for 40-Gb/s applications-compared performance with side-illuminated photodiodes

The design, fabrication, and performance of double-stage taper photodiodes (DSTPs) are reported. The objective of this work is to develop devices compatible with 40-Gb/s applications. Such devices require high efficiency, ultrawide band, high optical power handling capability, and compatibility with low-cost module fabrication. The integration of mode size converters improves both the coupling efficiency and the responsivity with a large fiber mode diameter. Responsivity of 0.6 A/W and 0.45 A/W are achieved with a 6-/spl mu/m fiber mode diameter and cleaved fiber, respectively, providing relaxed alignment tolerances (/spl plusmn/1.6 /spl mu/m and /spl plusmn/2 /spl mu/m, respectively), compatible with cost-effective packaging techniques. DSTPs also offer a wide bandwidth greater than 40 GHz and transverse-electric/transverse-magnetic polarization dependence lower than 0.2 dB. Furthermore, a DSTP saturation current as high as 11 mA results in optical power handling greater than +10 dBm and a high output voltage of 0.8 V. These capabilities allow the photodiode to drive the decision circuit without the need of a broad-band electrical amplifier. The DSTP devices presented here demonstrate higher responsivities with large fiber mode diameter and better optical power handling capabilities and are compared with classical side-illuminated photodiodes.     

Crosstalk between microstrip transmission lines

Methods for prediction of crosstalk between microstrip transmission lines are reviewed and simplified for the weak-coupling case. Classical coupled transmission line theory is used for uniform lines, and potential and induced EMF methods are used for crosstalk between nonuniform lines. It is shown that the potential method is equivalent to classical coupled transmission line theory for the case of uniform lines. An experiment was performed for uniform coupled microstrip lines for frequencies from 50 MHz to 5 GHz, and good agreement between theory and measurement was obtained for both near- and far-end crosstalk     

High-frequency analysis of the Ellipticus antenna

Efficient numerical solution techniques have been developed and used to examine the electromagnetic fields that can be developed in the working volume of the CW Ellipticus antenna operated at frequencies from 100 kHz to 1 GHz. An exponentially tapered transition section is designed to obtain the desired illumination pattern in the working volume. The input transition section is needed for impedance matching and to drive efficiently the Ellipticus antenna. A parametric study is performed to ascertain the performance of the Ellipticus antenna for frequencies up to 1 GHz     

Effects of error variation in means of measurement on reliability parameters in engineering-system monitoring

A method is given for calculating the monitoring reliability parameters (MRP) for an engineering system with allowance for the drift in the measurement error of the means of measurement (MM). The approach is based on introducing a biased MM error distribution into the traditional formulas for the conditional probabilities of spurious and unobserved failure. The bias at the center of the distribution is determined by the systematic error at the given instant. An example is given to illustrate the performance in MRP calculation.Translated from Izmeritel'naya Tekhnika, No. 1, pp. 12–13, January, 1994.