蒸汽喷射器射流场流动模型研究综述

综述了3种不同维数的喷射器射流场流动模型的研究工作,分析了3种模型各自的特点后指出,一维模型的建立主要基于定压混合理论或定常面积混合理论;二维偏微分方程模型建立后基于差分法等数值算法进行求解.随着网格技术和计算方法的提高,三维粘性射流场中激波和湍流的数值模拟发展迅速.     

以硅氧烷醇锂为催化剂的氟硅生胶的合成

介绍了单体三氟丙基甲基环三硅氧烷通过硅氧烷醇锂催化剂聚合成氟硅生胶,讨论了不同催化剂及其用量,原料中水分含量、不同乙烯基含量对氟硅生胶分子量的影响.     

高精度智能转速测量模板的设计

介绍了一种利用高性能的16位单片机80C196KC进行转速实时高精度的测量方法，阐述了如何通过CAN总线实现与微机通讯；详细描述了硬件电路的设计，并给出了软件程序框图。     

基于单片机技术的机械设备计时器的研制

介绍一种基于单片机和振动传感器技术，采用软、硬件结合设计的新型数字式机械设备计时器，分析了原理、硬件结构、技术方法、配套设备和软件功能。     

本钢7号高炉中控室10kV供电系统技术分析及改进方案实施

根据7号高炉中控室供电状况，进行了供电平衡分析。调整两段负荷，使供电平衡安全。     

Progress of Solid Electrolytes and the Electrochemical Sensors

Four types of solid state electrochemical sensors and their general principles are introduced in the paper. The novel type-IV sensors developed in the last few years are emphasized to study hereafter. The ways to design new electrochemical sensors and the directions to develop new solid electrolytes for new electrochemical sensors are also discussed.     

Matrix expression and reachability analysis of finite automata

In this paper,we propose a matrix-based approach for finite automata and then study the reachability conditions.Both the deterministic and nordeterministic automata are expressed in matrix forms,and th...     

软件项目质量控制流程及其技术

软件项目质量管理是贯穿整个软件生命周期的重要工作,有效地实施质量控制是提高软件质量、降低成本的重要手段。针对质量控制的难点,对质量控制流程与技术进行研究。首先,说明质量控制过程,包括事前质量控制、事中质量控制和事后质量控制;然后,通过图形研究质量控制流程;最后,通过图形并结合文字说明研究质量控制技术,包括因果图、Pareto图、控制图、运行图、统计抽样等5种常用技术。结果表明,通过对质量控制流程与技术的研究,为质量控制提供技术和方法支持,提高质量管理的科学性。     

Multi-channel SAR imaging based on distributed compressive sensing

The rapid development of compressive sensing(CS)shows that it is possible to recover a sparse signal from very limited measurements.Synthetic aperture radar(SAR)imaging based on CS can reconstruct the target scene with a reduced number of collected samples by solving an optimization problem.For multi-channel SAR imaging based on CS,each channel requires sufficient samples for separate imaging and the total number of samples could still be large.We propose an imaging algorithm based on distributed compressive sensing(DCS)that reconstructs scenes jointly under multiple channels.Multi-channel SAR imaging based on DCS not only exploits the sparsity of the target scene,but also exploits the correlation among channels.It requires significantly fewer samples than multi-channel SAR imaging based on CS.If multiple channels offer different sampling rates,DCS joint processing can reconstruct target scenes with a much more flexible allocation of the number of measurements offered by each channel than that used in separate CS processing.