RAID的存储信道分析

本文从冗余磁盘阵列的信道模型出发，研究各部分组成的理论与技术。文中在给出系统的模型描述之后，着重分析了冗余信息元生与检纠错、数据分割与同步。还研究了系统中的负荷平衡问题，指出了磁盘优化调度的方向。     

Measurements of distribution of self-bias potential on an RF-plane electrode in plasma etching devices

The self-bias potential (V_dc) induced on an RF-powdered electrode (153 mm Ø) in a plasma is measured using electrical probes which are buried in, de-insulated from, and RF-connected to the electrode. The configuration of the probes allows to study the distribution of V_dc discretely on the electrode. The potential is homogeneous in the absence of external magnetic field. In the presence of a homogeneous magnetic field parallel to the electrode, it is reduced and a monotonous gradient takes place in its distribution due to the plasma shift induced by E × B drift. When the magnetic field is rotated along the axis of the RF-electrode at a frequency less than 50 Hz, the distribution, which is almost identical to the one in a static field, rotates with the magnetic field. On the coordinate system rotating with the magnetic field, the probes are regarded to be rotating. The potential distribution is obtained as a continuous function of the azimuthal angle. Thus the rotation of the field provides information for the experimental interpolation.     

令牌多环网性能—可靠性综合评价

网络的性能与可靠性已分别得到广泛的研究,然而,怎样分析具有容错机制的环网的性能仍属有待开拓的研究领域,本文提出了一种分析具有自修复机制的多环网络系统的方法,并给出了报文传输时间分布的拉氏变换式,平均等待时间及平均队列长度公式,分析结果可用于评估故障与修复过程对实时令牌环网的实时响应特性的影响,对基于LAN的分布式实时系统设计具有指导意义。     

Measurement of the compressive creep strain rates of the individual phases within a lamellar microstructure

A fuducial line technique has been developed to determine the creep properties of the constituent phases within a lamellar composite subject to compression creep deformation. The technique can yield information on the total strain, creep rate, and the stress exponent and activation energy for creep of the individual phases within a lamellar microstructure. The contribution of interphase interfacial sliding to the strain of lamellar composites can also be evaluated by using the fiducial line technique. Application of the fiducial line analysis to a two-phase TiAl/Ti₃Al lamellar alloy deformed in compression at 1080K and 380MPa yields good agreement between the creep strain determined using the fiducial line analysis and the value directly measured from the crept specimen. The fiducial line analysis reveals that the TiAl phase within the two-phase TiAl/Ti₃Al lamellar microstructure creeps 2.2 times faster than the Ti₃Al phase and that interfacial sliding does not contribute to creep deformation of this alloy, within the resolution limit of the fiducial line experiment.     

Determining elasticity and strength characteristics of powder coating

Methods are described for forming coating specimens and testing them in pure bending. The proposed tester gives adequate accuracy in determining the elastic characteristics and strength for thin specimens (up to 0.1 mm) of brittle materials of powder-coating type.Translated from Problemy Prochnosti, No. 3, pp. 94–97, March, 1993.     

线性时变系统的区间稳定性与鲁棒稳定性

本文应用向量比较定理研究线性时变系统的区间稳定性和具非线性时变摄动的线性时变系统的鲁棒稳定性，所得的新结果包含文献的一些主要结果作为特例，本文的研究方法说明向量比较方法是分析区间稳定性和鲁棒稳定性的一种自然而有力的工具。     

Instron texture profile of buffalo milk cheddar cheese as influenced by composition and ripening changes

Buffalo milk Cheddar cheese samples of different ages were analysed for compositional attributes (CA), ripening indices (RI) and Instron Textural Profile (ITP). All samples were compositionally alike, except for pH and salt-in-moisture (SM) contents. RI showed significant variations. CA and RI showed highly significant correlations within themselves and with each other, except for moisture with pH, SM with moisture, MNFS, Fat and FDM and Fat with MNFS. The ITPs of cheeses showed significant variations and had highly significant intercorrelations indicating their interdependence. CA (except moisture and MNFS) and RI showed a highly significant correlationship with ITPs. Moisture content showed a highly significant correlationship with all ITPs, except cohesiveness and springiness, where it was significant. MNFS content showed significant correlations only with hardness and brittleness. Stepwise regression analysis revealed that MI was the most predominant factor influencing cheese texture, followed by pH, SM, FDM and TVFA. Knowing Ca and RI, the textural properties of cheeses can be forecast through mathematical equations. Similarly the age of cheese can also be predicted if RI and/or textural properties are known.     

Aromatic nitrations by mixed acid. Slow liquid-liquid reaction regime

Aromatic nitrations by mixed acid have been selected as a specific case of a heterogeneous liquid-liquid reaction. An extensive experimental programme has been followed using adiabatic and heat-flow calorimetry and pilot reactor experiments, supported by chemical analysis. A series of nitration experiments has been carried out to study the influences of different initial and operating conditions such as temperature, stirring speed and sulphuric acid concentration. In parallel, a mathematical model to predict the overall conversion rate has been developed. In this paper the mathematical modelling and the implementation and experimental validation for benzene, toluene and chlorobenzene mononitration in the kinetic control regime (slow liquid-liquid reaction) are presented and discussed.     

Separate assessment of porosity and uncombined carbon in cemented carbides

Porosity and uncombined carbon in cemented carbides are traditionally assessed by comparison to standardized microstructure charts, such as those in ISO 4505-1978. To improve the accuracy in the characterization a fully automatic image analysis procedure has been developed. The analysis is performed using light optical microscopy on unetched polished specimens. The implemented algorithm separates uncombined carbon, C-defects, from pores, A- and B-defects. Pores are approximately distributed in a random way in the structure. Uncombined carbon is on the other hand precipitated into clusters of carbon particles. This difference is together with defect size used as a base for the separation. Small defects situated close together are classified as C-defects, small isolated defects as A-pores and large defects as B-pores. Pores are found to be more round than the somewhat elongated C-defects. The difference in shape is significant and can also be used as a separation criterion.

Image analysis is used to quantitatively characterise the ISO 4505-1978 standard charts with respect to volume fraction, number density and size distribution of defects. The results are compared to measured distributions for true microstructures.     

Analysis of thin walled structures using the boundary element method

In this article the direct boundary element formulations of stretching and bending plate problems are combined together to solve thin walled structures and other similar frames. The final system is obtained by assuming each individual plane structural element as a subregion. After the necessary transforms of these equations they can be combined together taking into account the displacement compatibility and equilibrium conditions.