Evolution in Structural and Optical Properties of Stannic Oxide Xerogel upon Heat Treatment

Upon consecutive heat treatments at increasing temperatures, the microstructure of solution–sol–gel-derived stannic oxide (SnO₂) xerogel evolves in three stages: (I) below 300°C, characterized by extensive dehydroxylation and gel shrinkage with little grain growth and surface loss; (II) between 300° and 500°C, by extensive crystallization, leading to dramatic surface loss (by 70%); and (III) above 500°C, by grain growth. Concurrently, the UV-absorption edge shows red shifts during stages I and II and blue shifts during stage III, resulting in distinct color variations. The edge displacement bears a close correlation with a Raman "defect band" at ∼305–328 cm⁻¹.     

Reducing of heat loss of rubber compound using natural zeolite filler: effect of partially substitution of fillers on compound properties

The main objective of this work was reducing the heat loss of styrene butadiene rubber by partial substitution of carbon black with natural zeolite as a filler. Reducing the usage of carbon black in the rubber industry is a good strategy to decrease fossil fuel usage and global warming. There are different mineral fillers like silica and clay to be used instead of carbon black. Effect of application of natural zeolite on reducing the heat loss of rubber compound based on SBR was investigated by melt mixing of natural zeolite in rubber matrix in an internal mixer. Natural zeolite was selected as 5, 10, 15, and 20 phr. Carbon black was partially substituted with zeolite and the effect of natural zeolite content and structure on different aspects of the compound including heat buildup, hardness, elongation, and modulus were evaluated. It was shown that although cross-link density and mechanical properties of the compounds decreased a little, but a significant improvement was observed in the fatigue resistance of the compounds beside a favorable decrease in the heat buildup and abrasion loss with an increase in the natural zeolite loading. The rate of improvement in properties was slowed down at zeolite contents higher than 5 phr.     

A geostatistical approach for groundwater head monitoring network optimisation: case of the Sfax superficial aquifer (Tunisia)

In many developing countries, the groundwater monitoring network is randomly designed, and consequently needs to be revised and optimised to reduce operation time and cost, remove redundant piezometric data, and strengthen sparseness data zone with supplementary observation well. The geostatistical approach used in this work is based on the universal kriging variance combined with cross‐validation test. Hence, a rational interpolation of water table elevations was performed to evaluate the accuracy of data employed in the piezometric head modelling. In this study, the groundwater monitoring network of the Sfax superficial aquifer in the south east of Tunisia was optimised. The elimination of five observation wells induces the invariability in the variance of estimate due to their less contribution in interpretations of the groundwater level behaviour. However, 38 wells were added at areas of high variance of the kriging in order to ameliorate the spatial coverage of the monitoring network.     

Improving the physical and mechanical properties of particleboards made from urea–glyoxal resin by addition of pMDI

The effect of pMDI on physical and mechanical properties of the particleboards made from urea–glyoxal resin was investigated. The nontoxic and ecofriendly urea–glyoxal (UG) resin was synthesized under weak acid conditions, and its different properties were measured. Then, pMDI at various contents (4, 6 and 8% on resin solids) was added to the UG resin prepared. The thermal and physicochemical properties of the resins prepared as well as their water absorption, flexural properties (flexural modulus and strength) and internal bond (IB) strength of the particleboard panels bonded with them were measured according to standard methods. According to the physicochemical results obtained, the addition of pMDI significantly accelerated the gel time and increased the viscosity and solids content of UG resins. Differential scanning calorimetry indicated that the addition of pMDI decreases the onset and curing temperatures of the UG resin. Physical analysis results of the panels indicated that the particleboards made from UG resins with isocyanate yielded lower water absorption when compared to those bonded with the control UG resins. Based on the findings of this research work, the mechanical properties of particleboard panels bonded with UG resins could be significantly enhanced by the addition of increasing percentages of pMDI. The panels having 8 wt% pMDI exhibited the highest flexural modulus, flexural strength and IB strength value and the lowest water absorption among all the panels prepared.     

Analysis of multistage amplifiers with hybrid cascode feedforward compensation using a modified model for load impedance

Hybrid cascode feedforward compensation (HCFC) is an effective technique to stabilize nano-scale three-stage amplifiers driving ultra-large load capacitors. It divides the compensation capacitance and shares it between two high-speed local feedback loops embedded within the amplifier core. In this article, a systematic approach to analyze the transfer function and to evaluate the pole expressions of nano-scale HCFC amplifiers is presented. For the first time, the equivalent output impedance is successfully modeled to approximate the complicated transfer function of the HCFC amplifier without the need for lengthy pencil-and-paper calculations. An HCFC amplifier is designed and simulated in 90-nm CMOS technology, to verify the effectiveness of the new analytic approach. The simulated transfer function of the amplifier is almost identical to a calculated transfer function derived based on the new model.     

A novel algorithm to study the impact of the mismatch on analog building blocks: a case study in basic 35 nm CMOS amplifiers

In this paper, the context of modeling of the impact of mismatch and statistical variations on analogue circuit building blocks is emphasized. The aim is to develop a new algorithm which predicts the statistical behavior of important parameters of an amplifier including output resistance, voltage gain and trans-conductance. The relative error of standard deviation of statistical parameters will remain less than 5% compared with the most accurate Monte-Carlo (MC) simulations using atomistic library model-cards. In comparison with other models which are based on the normal distribution of parameters, the proposed model does not need this limiting presumption. On the other hand, the proposed algorithm is more efficient compared with time consuming MC atomistic simulations.     

Electrodes based on nano-tree-like vanadium nitride and carbon nanotubes for micro-supercapacitors

Vanadium nitride(VN) was deposited by DC-sputtering on a vertically aligned carbon nanotube(CNTs)template for the purpose of nano-structuration. This led to the fabrication of hierarchically composite electrodes consisting of porous and nanostructured VN grown on vertically aligned CNTs in a nano-treelike configuration for micro-supercapacitor application. The electrodes show excellent performance with an areal capacitance as high as 37.5 m F cm~(-2) at a scan rate of 2 mV s~(-1) in a 0.5 MK_2SO_4 mild electrolyte solution. Furthermore, the capacitance decay was only 15% after 20,000 consecutive cycles. Moreover,the capacitance was found to increase with VN deposit thickness. The X-ray photoelectron spectroscopy analyses of the electrodes before and after cycling suggest that the oxide layers that form at the VN surface is the responsible for the redox energy storage in this material. Such electrodes can compete with other transition metal nitride based electrodes for micro-supercapacitors.     

Adaptive Fuzzy Fault Tolerant Control Using Dynamic Sliding Mode

International Journal of Control, Automation and Systems - In this paper, an actuator fault tolerant control (FTC) has been designed using dynamic sliding mode control (DSMC) for single input...     

Effect of fortification with asparagus powder on the qualitative properties of processed cheese

The qualitative properties of processed cheese (PC) fortified with different levels of asparagus powder (AP) (0.5%, 1% and 1.5% wt/wt) were evaluated during storage. AP decreased the pH and lipolysis indexes and increased the phenolic content, antioxidant activity and proteolysis of the processed cheeses. AP made the structure of the cheese more elastic, increased the rigidity and decreased the spreadability compared with the control sample, which corresponded to the results obtained using dynamic oscillatory rheometry. The results showed that AP as a rich source of bioactive components could be used for the fortification of processed cheeses.