Analysis of the Datagram Congestion Control Protocol’s connection management procedures using the sweep-line method

State space explosion is a key problem in the analysis of finite state systems. The sweep-line method is a state exploration method which uses a notion of progress to allow states to be deleted from memory when they are no longer required. This reduces the peak number of states that need to be stored, while still exploring the full state space. The technique shows promise but has never achieved reductions greater than about a factor of 10 in the number of states stored in memory for industrially relevant examples. This paper discusses sweep-line analysis of the connection management procedures of a new Internet standard, the Datagram Congestion Control Protocol (DCCP). As the intuitive approaches to sweep-line analysis are not effective, we introduce new variables to track progress. This creates further state explosion. However, when used with the sweep-line, the peak number of states is reduced by over two orders of magnitude compared with the original. Importantly, this allows DCCP to be analysed for larger parameter values. Somsak Vanit-Anunchai was partially supported by an Australian Research Council Discovery Grant (DP0559927) and Suranaree University of Technology. Guy Edward Gallasch was supported by an Australian Research Council Discovery Grant (DP0559927).     

Real-time measurement of pointing action by using DSP

This paper presents an approach of measuring in real-time the vector of finger that is pointing to an object. DSP is used in the operation processing unit in order to do the real-time processing. The steps include the extraction of flesh-colored regions from an image, the labeling of the flesh-colored regions, and the detection of two characteristic positions on the finger so that the direction that the finger is pointing at will be calculated. The entire process takes about 29 msec, which makes it possible to have the frame rate of 34 fps. With this frame rate, this measurement approach is considered real-time and promising to be merged into other application systems. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

Multiterminal light-emitting logic device electricallyreprogrammable between OR and NAND functions

A monolithic multiterminal logic device that functions both optically and electrically as an ORNAND gate, is demonstrated for the first time. The device, based on the real-space transfer of hot electrons into a complementary collector layer, has been implemented in an InGaAs/InAlAs/InGaAs heterostructure grown by molecular beam epitaxy. Excellent performance is obtained at room temperature. The collector current and the optical output power both exhibit the OR and the NAND functions of any two of the three input terminals, these functions being interchangeable by the voltage on the third terminal     

Electrical properties and positron annihilation study of (Ba<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Ho<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>)TiO<Subscript>3</Subscript> ceramics

DC resistivity, dielectric constant, dielectric loss and positron annihilation spectra of (Ba_1−x Ho _x )TiO₃ ceramics have been measured as a function of holmium concentration x. It has been found that the DC resistivity of (Ba_1−x Ho _x )TiO₃ is strongly dependent on the Ho content: it decreases three orders of magnitude and reaches a minimum at x = 0.4%. Doping with 0.6% holmium increases the permittivity of BaTiO₃ by approximately three times (from ∼1,300 to ∼4,000), with only a slight increase in the corresponding dielectric loss. The local electron density and defect concentration estimated using positron annihilation technique conforms well to the features found in the dielectric and resistivity measurements. The results have been discussed in terms of a mixed compensation model.     

Laser scanning path generation considering photopolymer solidification in micro-stereolithography

It is essential to automate the scanning path generation process to effectively implement the micro-stereolithography. However, a scanning path that is generated based only on a 3D CAD model introduces dimensional inaccuracies. In micro-stereolithography, the photopolymer solidification is affected by fabrication conditions, such as the optical properties (laser power, laser scanning speed, laser scanning pitch focusing condition, etc.) and material properties of the photopolymer. Thus, the photopolymer solidification phenomena must be considered when generating a laser scanning path. In this paper, a scanning path generation algorithm that uses 3D CAD data and considers the photopolymer solidification phenomena is proposed to improve the dimensional accuracy in micro-stereolithography. Multi-line photopolymer solidification experiments were performed for various laser scanning conditions to examine the photopolymer solidification phenomena. From these experiments, linear relations between the solidification length (width) and scanning length (width) were acquired and stored in a database. Subsequently, these data were utilized to compensate the scanning path of the laser beam. In addition, experiments for determining the layer thickness in the z-direction were performed and these results were also used in the scanning path generation algorithm.This research was supported by the Highly Advanced National Project (http://www.most.go.kr), which performs some of the National R&D Program, and sponsored by the Korean Ministry of Science and Technology under the contract project code M10214000116-02B1500-02010.