PTA压力离心机转子的改造

介绍了PTA压力离心机的主要性能参数、工作原理、分离效果的影响因素。为了增大沉渣在过渡区及脱水区滞留的时问，同时为达到在过渡区及脱水区对沉渣加入纯净水进行再冲洗的目的，对螺旋送料转子、挡液环、进料管进行了改造。改造后，沉渣在脱水区的停留时间由0．44a增至0．72s，2．5～3t／h的冲洗水对脱水区的沉渣进行冲洗效果较好。产品中的杂质质量分数较改造前减少15％，产品优等品率提高到99％。     

一台循环流化床锅炉U型二次分离的改进对过热器爆管的影响

文章通过对一台循环流化床锅炉U型二次分离装置的改进，减少了过热器爆管的介绍，给出了采用多次离心分离技术，改善和提高烟尘分离效率，从而改善过热器外部工作条件，达到减少爆管发生的措施，相应提出了一些有关的建议。     

均匀设计法分析制备过程对钴钼硫化物催化剂机械强度的影响

建立了CoMoP/Al2O3加氢精制催化剂机械强度及其可靠性在制备过程中的数学模型,采用均匀设计考察了浸渍、干燥、煅烧、硫化4个制备过程中,浸渍时间、干燥温度、干燥时间、煅烧温度、煅烧时间、硫化温度和硫化升温速率7个实验因子对催化剂强度均值、Weibull模量的影响,同时考察了这些因素对颗粒密度的影响。方差分析表明所有模型都是充足的。实验结果表明,硫化过程是影响催化剂强度均值的主要过程。在实验范围内提高硫化温度、降低硫化时的升温速率有利于提高催化剂的强度。影响催化剂Weibull模量的因素主要为各个制备过程的交互效应。要提高催化剂强度的可靠性就必须全面考虑催化剂制备的各个过程,特别是各个制备过程的交互效应。     

Aging response of the young’s modulus and mechanical properties of Ti-29Nb-13Ta-4.6Zr for biomedical applications

Alloys for implant devices require improved strength but a reduced Young’s modulus, in order to become mechanically more compatible with adjacent bone tissues. In this study, a new metastable β-type titanium alloy, Ti-29Nb-13Ta-4.6Zr (wt pct), was subjected to aging treatment to produce different microstructures, and the resulting mechanical properties, including the Young’s modulus, were measured. The Young’s modulus of this alloy is found to be sensitive to microstructures generated by various heat treatments. For microstructures varying from (α + β) to (α + β + ω) and (β + ω), the Young’s modulus increases with an accompanying increase in tensile strength and hardness, but decreases in ductility. The (β + ω) microstructure has a low strength, high modulus, and poor ductility and cannot be used for biomedical applications. For an (α + β) microstructure, the volume fraction of the phases is shown to be the main factor that determines the mechanical properties.     

A distributed adverse drug reaction detection system using intelligent agents with a fuzzy recognition‐primed decision model

Discovering unknown adverse drug reactions (ADRs) in postmarketing surveillance as early as possible is highly desirable. Nevertheless, current postmarketing surveillance methods largely rely on spontaneous reports that suffer from serious underreporting, latency, and inconsistent reporting. Thus these methods are not ideal for rapidly identifying rare ADRs. The multiagent systems paradigm is an emerging and effective approach to tackling distributed problems, especially when data sources and knowledge are geographically located in different places and coordination and collaboration are necessary for decision making. In this article, we propose an active, multiagent framework for early detection of ADRs by utilizing electronic patient data distributed across many different sources and locations. In this framework, intelligent agents assist a team of experts based on the well‐known human decision‐making model called Recognition‐Primed Decision (RPD). We generalize the RPD model to a fuzzy RPD model and utilize fuzzy logic technology to not only represent, interpret, and compute imprecise and subjective cues that are commonly encountered in the ADR problem but also to retrieve prior experiences by evaluating the extent of matching between the current situation and a past experience. We describe our preliminary multiagent system design and illustrate its potential benefits for assisting expert teams in early detection of previously unknown ADRs. © 2007 Wiley Periodicals, Inc. Int J Int Syst 22: 827–845, 2007.     

Quasi-Chun-Ching Shih''''s Fractional Fourier Transform with Periodicity of 2,3 and M

Based on Chun-Ching Shih's idea, the basic transform was substituted and the quasi-ChunChing Shih's fractional Fourier transform with periodicity of 2, 3 and M was deduced. The two former transforms and the Chun-Ching Shih's fractional Fourier transform were only the particular cases of quasiChun-Ching Shih's fractional Fourier transform with periodicity of M.     

Analysis and Simulation of S-shaped Waveguide in Silicon-on-insulator

The simulation and analysis of S-shaped waveguide bend are presented.Bend radius larger than 30 mm assures less than 0.5 dB radiation loss for a 4-μm-wide silicon-on-insulator waveguide bend with 2-μm etch depth.Intersection angle greater than 20° provides negligible crosstalk (<-30 dB) and very low insertion loss.Any reduction in bend radius and intersection angle is at the cost of the degradation of characteristics of bent waveguide and intersecting waveguide, respectively.     

Fast algorithms for determining the linear complexity of sequences over GF(p/sup m/) with period 2/sup t/n

We prove a result which reduces the computation of the linear complexity of a sequence over GF(p^m) (p is an odd prime) with period 2n (n is a positive integer such that there exists an element bisinGF(p^m), bⁿ=-1) to the computation of the linear complexities of two sequences with period n. By combining with some known algorithms such as the Berlekamp-Massey algorithm and the Games-Chan algorithm we can determine the linear complexity of any sequence over GF(p^m) with period 2^tn (such that 2 ^t|p^m-1 and gcd(n,p^m-1)=1) more efficiently     

含V、N无缝钢管表面外折缺陷产生原因的分析

通过对鞍钢生产的部分批号V、N微合金强化无缝钢管及生产该钢管的原料连铸坯和连轧管坯的表面缺陷进行研究，分析了含V、N钢管表面外折缺陷的成因，提出了改善钢管表面质量的方法。采用改进后工艺生产的无缝管，其表面外折废品量大幅度降低。