Telerobot-enabled HUB-CI model for collaborative lifecycle management of design and prototyping

The HUB-CI model is investigated in a telerobotic system in a client/server network to manage the lifecycle of engineering design and prototyping. The purpose of this platform is to support collaborative engineering design and proof of concept to enhance distributed team collaboration and resource utilization. The suggested platform is exemplified in two collaboration support tools and a physical prototyping platform. Structured Co-Insight Management is developed to support innovative idea exchanges and the consensus decision-making during the design process. Conflict/error detection management helps preventing conflicts and errors during the lifecycle of design and development. Physical collaboration over the network occurs when a team controls the telerobot operation during prototyping and testing in design cycles. A pilot system is implemented with a group project for the design of an electronic circuit (including both hardware and software designs). The functional assessment method is used to compare this platform to other collaborative design tools. The system presented offers unique qualitative advantages as an integrated collaboration support system.     

F离子掺杂TiO2的性能研究

以NH4F为掺杂剂，采用溶胶-凝胶法制备F离子掺杂型TiO2光催化剂，对其进行XRD、XPS和PL表征，结果表明，F离子掺杂ToO2由于Ti—F配位体的形成而能抑制金红石相的生成，同时F离子掺杂能增加TiO2表面缺陷浓度并降低Ti2P键的结合能，另外，由于F离子能取代Ti—OH配位体而降低了表面羟基氧浓度．光催化研究结果表明，F离子掺杂提高了TiO2光催化活性近1．5倍．     

基于PLC的水泥生料配料控制系统研究

1 率值控制工艺结构 衡量生料质量的标准是水泥的三个率值．石灰石饱和系数KH、硅酸率SM、铝氧率IM，即在出磨生料中，、Fe2O3、Al2O3、SiO2诸氧化物的百分比含量必须满足以下二三式：     

Preparation of phenolic resin derived 3-D ordered macroporous carbon

Three-dimensionally ordered long-range macroporous carbon structures were prepared using commercially available phenolic resin by utilizing sacrificial colloidal silica crystalline arrays as templates that were subsequently removed by HF etching after pyrolysis in an argon atmosphere. SEM, TEM, and BET were employed to characterize the morphology and the surface area of the porous carbon structures. The pore size (150–1000 nm) and BET surface area, which reflect pore volume (298.6 m²/g (1.32 cm³/g) ∼ 93.7 m²/g (0.12 cm³/g)), of the macroporous carbon structures produced were approximately proportional to the size (150–1000 nm) of the sacrificial silica sphere templates used (annealing temp. 550°C). The achieved 550 nm porous carbon structures were examined to function as potential catalyst carriers and were successfully impregnated with Ag or Pt-Ru on their inner walls after borohydride reduction at room temperature. In addition, porous carbon patterns were fabricated using the ‘micromolding in capillary’ technique, which has potential applications in the microreaction technology.     

有色双细全牵伸丝的研制开发

从生产实践出发,探讨了33dtex/24f双细全牵伸丝（FDY）丝的生产工艺。在选择工艺参数时应考虑色母粒对纺丝生产的影响。合理地选择纺丝温度、喷丝板孔径、拉伸速度、牵伸倍数可稳定地生产性能良好的FDY丝。     

心理资本前因变量研究

采用心理资本问卷对分别属于医药、建筑、水利工程、电信、通讯运营和服务行业的6家企业的员工进行了调查.根据对回收的283份有效问卷的统计分析,认为员工的性别、受教育程度和所在企业的性质对员工心理资本不会产生显著性影响,而员工年龄的影响显著,50岁以上员工的总体心理资本水平高于其他年龄段员工.     

多维超几何分布的最可能成功数

超几何分布是一种重要的离散型概率分布,本文利用反证法以及比较法求出了三维超几何分布的最可能成功次数,并在此基础上,求出了多维超几何分布的最可能成功次数.     

Fabrication and characterization of nano silver powder prepared by spray pyrolysis

Silver powder was fabricated by spray pyrolysis, using 2%–20% AgNO₃ solution, 336–500 mL/h flux of AgNO₃ solution, 0.28–0.32 MPa flux of carrier gas and in the 620–820 °C temperature range. The effects of furnace set temperature, concentration of AgNO₃ aqueous solution, flux of AgNO₃ aqueous solution as well as carrier gas on the morphology and particle size distribution of silver powder, were investigated. The experimental results showed that with the high concentration of AgNO₃ aqueous solution, the average grain size of silver decreased with the increasing of furnace set temperature. But the gain size distribution was not homogenous, the discontinuous grain growth occurred. With the low concentration of AgNO₃ aqueous solution, the higher furnace set temperature made the nano sliver grains sintered together to grow. Nano silver powder about 100 nm was fabricated by spray pyrolysis, using 2wt% AgNO₃ solutions, 336 mL/h flux of AgNO₃ aqueous solution, 0.32 MPa flux of carrier gas at 720 °C furnace set temperature.     

Zonal disintegration phenomenon in enclosing rock mass surrounding deep tunnels -- Elasto-plastic analysis of stress field of enclosing rock mass

The zonal disintegration phenomenon (ZDP) is a typical phenomenon in deep block rock masses. In order to investigate the mechanism of ZDP, an improved non-linear Hock-Brown strength criterion and a bi-linear constitutive model of rock mass were used to analyze the elasto-plastic stress field of the enclosing rock mass around a deep round tunnel. The radius of the plastic region and stress of the enclosing rock mass were obtained by introducing dimensionless parameters of radial distance. The results show that tunneling in deep rock mass causes a maximum stress zone to appear in the vicinity of the boundary of the elastic and the plas-tic zone in the surrounding rock mass. Under the compression of a large tangential force and a small radial force, the rock mass in the maximum stress zone was in an approximate uniaxial loading state, which could lead to a split failure in the rock mass.     

谈高职大学生职业素质教育

职业素质教育是高等职业教育以就业为导向教学改革的前提和保障,本文论述了高等职业院校实施职业素质教育的必然性、涵义、任务、内容、方法及现实意义进行了详细的阐述。