Spatial retardation of carrier heating in scaled 0.1-μmn-MOSFET's using Monte Carlo simulations

A comprehensive Monte Carlo simulator is employed to investigate nonlocal carrier transport in 0.1 μm n-MOSFET's under low-voltage stress. Specifically, the role of electron-electron (e-e) interactions on hot electron injection is explored for two emerging device designs biased at a drain voltage V_d considerably less than the Si/SiO₂ injection barrier height φ_b. Simulation of both devices reveal that 1) although qV_d<φ_b, carriers can obtain energies greater than φ_b, and 2) the peak for electron injection is displaced approximately 20 nm beyond the peak in the parallel channel electric field. These phenomena constitute a spatial retardation of carrier heating that is strongly influenced by e-e interactions near the drain edge. (Virtually no injection is observed in our simulations when e-e scattering is not considered.) Simulations also show that an aggressive design based on larger dopant atoms, steeper doping gradients, and a self-aligned junction counter-doping process produces a higher peak in the channel electric field, a hotter carrier energy distribution, and a greater total electron injection rate into the oxide when compared to a more conventionally-doped design. The impact of spatially retarded carrier heating on hot-electron-induced device degradation is further examined by coupling an interface state distribution obtained from Monte Carlo simulations with a drift-diffusion simulator. Because of retarded carrier heating, the interface states are mainly generated further over the drain region where interface charge produces minimal degradation. Thus, surprisingly, both 0.1 μm n-MOSFET designs exhibit comparable drain current degradation rates     

Berechnung der Wirbelstromdichten und-kräfte in der Umgebung großer supraleitender Spulen für den magnetischen Einschluß bei der Kernfusion

Übersicht Um die Betriebssicherheit großer supraleitender Magnetsysteme für die Kernfusionsforschung zu gewährleisten, muß die im Magnetsystem gespeicherte Energie schnell entladen werden können. Durch die veränderlichen großvolumigen Magnetfelder werden in benachbarten leitfähigen Strukturen durch Induktion hohe Wirbelströme hervorgerufen. Durch sie treten dort elektromagnetische Kräfte. auf, die einzelne Komponenten mechanisch überlasten können. Zur Berechnung dieser Kräfte wurde eine einfache numerischanalytische Methode entwickelt, die im folgenden vorgestellt und mit Finite-Elemente-Verfahren verglichen wird.

---

Calculation of eddy current densities and forces around large superconducting coils for nuclear fusion

Contents The reliable operation of the superconducting magnet systems used for the magnetic confinement in nuclear fusion research requires the ability of a fast discharge of the stored magnetic energy. The corresponding magnetic field variation gives rise to high eddy currents by inductive coupling with surrounding conductive components. The eddy current forces can lead to a mechanical overload of some of these components. A simple numerical-analytical method was developed in order to calculate these forces. This method is presented and compared with the Finite Element Method.

     

Phase I trial of inhaled natural interleukin 2 for treatment of pulmonary malignancy: toxicity, pharmacokinetics, and biological effects

Safety, local and systemic immunomodulation, and tumor response to treatment with aerosolized natural interleukin 2 (nIL-2) applied five times a day were studied in a Phase I trial in 16 patients with pulmonary malignancies refractory to conventional therapy. The toxicity of inhaled nIL-2 was different from that observed after systemic administration. Reversible airway irritation causing a nonproductive cough represented the dose-limiting toxicity. Mild to moderate reduction of the vital capacity and forced expiratory volume (FEV1) with minor effects on relative FEV1, peak expiratory flow, airway resistance, and PaO2 was experienced by individual patients. In 14 patients suffering from pulmonary metastases due to renal cell cancer, one durable complete response, one partial response, and one mixed response were observed. Inhalation of nIL-2 aerosol resulted in a dose-dependent expansion of pulmonary immunocompetent cells in bronchoalveolar lavage fluid. Posttreatment bronchoalveolar lavage showed an activated lymphocyte phenotype with increased HLA-DR expression. The only systemic biological effect detectable in peripheral blood was a marked increase of soluble interleukin 2 receptor serum levels. We conclude that treatment with aerosolized nIL-2 is an effective means for site-specific immunomodulation and deserves further investigation for the treatment of malignant and inflammatory lung disease.     

Influence of joint detail on the flexural/torsional interaction of thin-walled structures

For a structure formed from two thin-walled open members connected at 90°, torsion applied to one member can result in torsion as well as flexure in the second member, with the magnitude and direction of this torsion as well as flexure in the second member being determined by the type of joint used. Conventional structural analysis would normally assume the presence of only flexure in the second member. The results from a finite element study of structures formed from thin-walled channel sections connected by box, mitre and stiffened mitre joints is presented and an explanation for the behaviour of the different joint types is given. It is shown that for the box joint the warping deformation of the loaded member is the dominant factor in determining the magnitude and direction of the twisting of the second member, whilst this is determined for the stiffened mitre joint primarily by the St Venant rotation deformation of the loaded member. For the unstiffened joint it is shown that the warping and St Venant rotation deformation effects tend to cancel each other out.     

THE FRACTURE MECHANISM OF 475°C EMBRITTLEMENT IN A DUPLEX STAINLESS STEEL

The mechanism of “475°C embrittlement” of a duplex stainless steel was investigated using finite element modelling of the stress distribution at brittle fracture initiation. Brittle fracture initiated at a critical shear stress, which increased with ferrite hardness. The fracture stress was affected by the duplex microstructure. Fracture was nucleated by deformation twins, which were identified using electron back-scatter diffraction. The ductile-to-brittle fracture transition was sensitive to age-hardening and could be described simply by the effect of age-hardening and test temperature on the yield stress.     

Effect of the pressure drop rate on cell nucleation in continuous processing of microcellular polymers

Microllular plastics are cellular polymers characterized by cell densities greater than 10⁹ cells/cm³ and cells smaller than 10 μm. One of the critical steps in the continuous production of microcellular plastics is the promotion of high cell nucleation rates in a flowing polymer matrix. These high nucleation rates can be achieved by first forming a polymer/gas solution followed by rapidly decreasing the solubility of gas in the polymer. Since, in the processing range of interest, the gas solubility in the polymer decreases as the pressure decreases, a rapid pressure drop element, consisting of a nozzle, has been employed as a continuous microcellular nucleation device. In this paper, the effects of the pressure drop rate on the nucleation of cells and the cell density are discussed. The experimental results indicate that both the magnitude and the cell density are discussed. The experimental results indicate that both the magnitude and the rate of pressure drop play a strong role in microcellular processing. The pressure phenomenon affects the thermodynamic instability induced in the polymer/gas solution and the competition between cell nucleation and growth.     

Electrical characterization of very-narrow-gap bulk HgCdTe single crystals by variable magnetic field hall measurements

Variable-magnetic-field Hall measurements (0 to 1.5 T) are performed on very-narrow-gap bulk-grown Hg_1−xCd_xTe single crystals (0.165 ≤ x ≤ 0.2) at various temperatures (10 to 300K). The electron densities and mobilities are obtained within the one-carrier (electrons) approximation of the reduced-con-ductivity-tensor scheme. The present data together with the selected data set reported by other workers exhibit a pronounced peak when the electron mobility is plotted against the alloy composition x-value which has been predicted to be due to the effective-mass minimum at the bandgap-crossing (E_g ≈ 0). The observed position (x ≈ 0.165), height (≈4 x 10² m²Vs), and width (≈0.01 in x) of the mobility-peak can be explained by a simple simulation involving only ionized-impurity scattering. A lower bound of the effective mass is introduced as a fitting parameter to be consistent with the finiteness of the observed electron mobility and is found to be of the order of 10⁻⁴ of the mass of a free electron.     

New lamps for old: the story of electric lighting

Of all the products of electrical technology, none has made a more profound difference to our way of life than the humble light bulb. The author describes the history of the light bulb from the time it was introduced and started to replace gas lamps to the present day. In particular the author discusses the early developments in arc lighting and incandescent filament lamps. The author also discusses the introduction of mercury vapour lamps, fluorescent lamps, and evacuation of the lamps