Formulation for Reliable Analysis of Structural Frames

Structural engineers use design codes formulated to consider uncertainty for both reinforced concrete and structural steel design. For a simple one-bay structural steel frame, we survey typical uncertainties and compute an interval solution for displacements and forces. The naive solutions have large over-estimations, so we explore the Mullen-Muhanna assembly strategy, scaling, and constraint propagation to achieve tight enclosures of the true ranges for displacements and forces in a fraction of the CPU time typically used for simulations. That we compute tight enclosures, even for large parameter uncertainties used in practice, suggests the promise of interval methods for much larger structures.     

SCC casting prediction for the realization of prototype VHPC-precambered composite beams

Casting simulations of self-compacting concrete are carried out in order to obtain a value of the minimum fluidity needed to cast a VHPC precambered composite beam. The mix proportioning of the concrete takes into account this minimum value. The numerical predictions are finally compared with the experimental observations during two casting tests and the real casting of the two 13 m beams. Although the simplifying assumptions needed to carry out the simulations are numerous, there is an agreement between the predictions and the real casting.     

Critical Configurations for 1-View in Projections from ℙ<Superscript>k</Superscript> → ℙ<Superscript>2</Superscript>

In this paper we describe, from a theoretical point of view, critical configurations for the projective reconstruction of a set of points, for a single view, i.e. for calibration of a camera, in the case of projections from ℙ^k to ℙ² for k ≥ 4. We give first a general result describing these critical loci in ℙ^k, which, if irreducible, are algebraic varieties of dimension k−2 and degree 3. If k=4 they can be either a smooth ruled surface or a cone and if k = 5 they can be a smooth three dimensional variety, ruled in planes, or a cone. If k≥ 6, the variety is always a cone, the vertex of which has dimension at least k − 6. The reducible cases are studied in Appendix A. These results are then applied to determine explicitly the critical loci for the projections from ℙ^k which arise from the dynamic scenes in ℙ³ considered in [13]. Marina Bertolini is currently Associate Professor of Geometry at the Department of Mathematics at the Università degli Studi di Milano, Italy. Her main field of research is Complex Projective Algebraic Geometry, with particular interest for the classification of projective varieties and for the geometry of Grassmann varieties. On these topics M. Bertolini has published more than twenty reviewed papers on national and international journals. She has been for some years now interested also in applications of Algebraic Geometry to Computer Vision problems. Cristina Turrini is Associate Professor of Geometry at the Department of Mathematics of Università degli Studi di Milano, Italy. Her main research interest is Complex Projective Algebraic Geometry: subvarieties of Grassmannians, special varieties, automorphisms, classification. In the last two years she has started to work on applications of Algebraic Geometry to problems of Computer Vision. She is author or co-author of about thirty reviewed papers. She is also involved in popularization of Mathematics, and on this subject she is co-editor of some books.     

Phase equilibria of the ternary Al-Cu-Ni system and interfacial reactions of related systems at 800 °C

A series of Al-Cu-Ni alloys of various compositions were made and annealed at 800 °C. The equilibrium phases were studied by metallography, X-ray diffraction (XRD) analysis, and electron probe microanalysis. The isothermal section of the ternary Al-Cu-Ni system at 800 °C was then determined based on these experimental results and the available phase relationship knowledge of the three constituent binary systems. No ternary compound was found. All three phases, AlNi₃, AlNi, and Al₃Ni₂, have very high ternary solubility, especially the AlNi phase, which almost reaches the binary Al-Cu side. However, no continuous solid solution was formed between the AlNi phase and any of the binary Al-Cu phases. Interfacial reactions of Al/Ni, Al/Cu, Al-Cu/Ni, and Al-Ni/Cu at 800 °C were investigated by using reaction couple techniques. The results showed that Al₃Ni and Al₃Ni₂ phases were formed in the Al/Ni couples; β-AlCu₄, γ ₁-Al₄Cu₉, and ɛ ₂-Al₂Cu₃ phases were formed in the Al/Cu couples. As for the results in the Al-2 at. pct Ni/Cu, Al-5 at. pct Ni/Cu, and Al-2 at. pct Cu/Ni, Al-4.5 at. pct Cu/Ni, and Al-6 at. pct Cu/Ni were similar to those in the binary Al/Cu and Al/Ni couples, respectively. A different reaction path was found in the Al-7.5 at. pct Cu/Ni couples, and an AlNi solid solution layer was formed instead of the Al₃Ni and Al₃Ni₂ phases.     

Formation of linear aldehydes during surface water preozonization and their removal in water treatment in relation to mutagenic activity and sum parameters

Low molecular weight aldehydes were formed during surface water preozonization, their levels showing a positive correlation with increasing ozone dose applied and with increasing water temperature. A strong negative correlation was observed between aldehyde levels and U.V. absorbance at 254 nm.Coagulation had no influence on the aldehydes present and the influence of rapid double layer filtration varied strongly with temperature : significant removals were only observed above 10°C.Mutagenic activity generated by preozonization in Salmonella typhimurium TA98 shows an ozone dose depending relationship different from the formation of linear aldehydes. Its removal by coagulation is not effective but rapid double layer filtration reduces mutagenic activity to marginal levels.In this respect too no clear parallel can be drawn between the presence of low molecular weight aldehydes and mutagenic activity.     

The hot blow forming of AZ31 Mg sheet: Formability assessment and application development

The hot blow forming of magnesium sheet offers significant opportunity for forming complex, lightweight parts for automotive applications. This paper characterizes the elevated-temperature formability of AZ31 magnesium sheet materials and the effect of processing conditions on the performance of these materials. In addition, magnesium sheet application development at General Motors Corporation is reviewed.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Quality of Crude Fish Oil Extracted from Herring Byproducts of Varying States of Freshness

ABSTRACT: Herring byproducts were stored at 2 and 15 °C for up to 72 h. Over time, significant increases of total volatile bases (TVB), histamine, putrescine, cadaverine, and tyramine were detected. However, only tyramine and TVB levels were temperature-dependent. The level of total polyunsaturated fatty acids (PUFAs) was constant. Longer byproducts storage gave rise to an oil with higher levels of free fatty acids, eicosapentaenoic acid (EPA), docosahexaenoic acid (DHA), and total PUFAs, while fluorescent compounds were lower. A higher storage temperature led to oil higher in α-tocopherol and EPA levels and lower in anisidine value. Surprisingly, the oil with the highest content of PUFAs was not produced from the freshest byproducts, and oil with low oxidation products can be extracted from stored byproducts.     

Instructional texts rewritten by five expert teams: Revisions and retention improvements.

700 undergraduates were tested in 3 experiments on original or rewritten versions of 52 instructional texts about Army job tasks, general science, philosophy, and history. Five experts had rewritten various sets of the texts and stated hypotheses about the efficacious features of their revisions. We tested their hypotheses and several others. Recall and recognition tests were given immediately and after a 24-hr delay. Results showed that revisions made by 3 of the 5 experts improved retention of text information. The kind and number of revisions and improvements varied across the text sets. Most expert hypotheses were not supported, and they made many revisions they were declaratively unaware of. Some of our hypotheses about the revision features were supported, but different features were effective for different sets of texts. It was concluded that some experts have effective knowledge about improving instructional text, but it exists primarily in procedural form. (PsycINFO Database Record (c) 2010 APA, all rights reserved)