Selectivity of partial hydrogenation reactions performed in a pore-through-flow catalytic membrane reactor

The selectivity of partial hydrogenation reactions of unsaturated substrates was studied in a membrane reactor operating at 323 K and 40 bar hydrogen pressure. The reactor system was constructed as a loop of a saturation vessel and a membrane module in which the reaction mixture was resaturated with hydrogen up to 100 times. In a porous membrane made from cross-linked polyacrylic acid palladium nanoparticles were incorporated as catalysts. A well-defined residence time within the membrane was achieved due to a defined pore structure of the membrane and a convective mass flow of the reaction mixture through the membrane. The selectivity for the partially hydrogenated products was investigated as a function of the pore size of the PAA membrane and was compared to commercially available catalysts. Compared to experiments with supported catalysts (Pd/C and Pd/Al₂O₃) in a slurry and a fixed bed reactor the selectivity for the desired products could be increased by 3% (1-octyne) up to 40% (geraniol).     

Positive interpolation with rational quadratic splines

A necessary and sufficient criterion is presented under which the property of positivity carry over from the data set to rational quadratic spline interpolants. The criterion can always be satisfied if the occuring parameters are properly chosen.     

刚性棒状全芳香液晶聚酯的合成及性质的研究

以溴和苯基取代的对苯二甲酰氯及2，2′-二甲基联苯-4，4′-二甲酰氯作为单体，分别与甲基、叔丁基、苯基取代的对苯二酚经熔融缩聚反应，合成一类具有刚性棒状结构的全芳香液晶聚酯。聚酯的热性质以TGA、DSC，热台偏光显微镜研究。所有的聚酯均为热致性液晶，它们具有相对较低的转变温度，在普通的有机溶剂中具有较好的溶解性质。     

Interaction bounds in multivariable control systems

Time-domain limitations due to right half-plane zeros and poles in linear multivariable control systems are studied. Lower bounds on the interaction are derived. They show not only how the location of zeros and poles are critical in multivariable systems, but also how the zero and pole directions influence the performance. The results are illustrated on the quadruple-tank process, which is a new multivariable laboratory process.     

Magnetic force microscopy studies on the magnetic ordering in organic materials induced by high-energy proton irradiation

In this study, ferromagnetic microstructures in highly oriented pyrolytic graphite and superparamagnetic spots in polyimide foils were created by 2.25 MeV proton microbeam irradiation and characterized using atomic and magnetic force microscopy. For this purpose, graphite samples were irradiated with cross-like patterns of 15 μm × 15 μm size using ion fluences in the range of (0.003–2.5) × 10¹⁸ cm⁻². The irradiated crosses showed strong magnetic signals and a complex domain structure in the magnetic images depending on the geometrical dimensions of the crosses. Furthermore, polyimide foils were irradiated with microspots and fluences in the range of (0.016–3.1) × 10¹⁹ cm⁻². Magnetic force microscopy shows very strong phase shifts in these irradiated areas.     

A microbubble-powered bioparticle actuator

We present the results of a device that uses controllable microbubble actuation to manipulate bioparticles. In order to create a useful device for controlling the position of bioparticles, predictable microfluidic actuation is crucial. The goal of this project was to develop fundamental technology that can be used to manipulate single bioparticles (e.g., cells). We use a thermal bubble actuation method to accomplish this goal. Microbubbles have the advantages of relatively simple electronics and fabrication but can be difficult to control. In this paper, we describe two specific accomplishments: the use of micromachined nucleation cavities to precisely localize thermal bubbles and to achieve controllable bubble formation temperatures and bubble dissipation and the demonstration of controllable microbubbles in a new device for particle sorting.     

Überlegungen zur Erweiterung des Klebstoffangebots im Holzleimbau

The procedure of testing adhesives for glulam production depends in Europe on the kind of resin. For example the testing of phenol-formaldehyde resins (PF-resins) includes the boiling test method, because the curing rate of these resins show a significant correlation between the strength after boiling and the resistance to moisture influence. On the other hand this test method is commonly insufficient for testing other resins. The results of investigations of glulam based on different kinds of resins show that there is a possibility to substitute the boiling test by a short-time accelerated aging method (KZB-Test) which will offer the same differentiation.