Frequency response function of magnetic bearings using high-temperature superconductor

A high-temperature superconductor YBa₂Cu₃O_7-x with strong pinning force has allowed stable magnetic suspension with no control to be developed. Two types of superconducting magnetic bearings (SMB) using YBCO and permanent magnet were assembled. The two types are radial and axial. The dynamic stiffness of each SMB as it was cooled down under a magnetic field by liquid nitrogen was measured both radially and axially. As a result, it was found that the spring constants of these SMBs were almost as large as a practically desirable value; however, their damping coefficients were lower than the practical level. These findings are useful as one of the data bases for development of an optimum SMB design to support the weight of rotors in an axial direction.     

Radiation tolerance of type IIa synthetic diamond detector for 14 MeV neutrons

Radiation tolerance of a type IIa synthetic diamond detector was examined from irradiation of mono-energetic 14 MeV neutrons. Measurements of I–V (current–voltage) characteristics and energy spectrum for 5.486 MeV alpha particles were performed after neutron irradiation. In the I–V characteristics measurement, enhancement of rectification was observed after neutron irradiation of up to 2.0 × 10¹² n/cm². Concurrently with the enhancement of rectification, significant decrease in signal amplitude was observed in energy spectrum measurement for alpha particles. It is considered that these changes were due to increase in the concentration of defects acting as shallow energy levels in the forbidden band. For neutron irradiation of higher than 1.6 × 10¹³ n/cm², weakening of the rectification characteristics and recovery of the signal amplitude were observed. These changes imply that deep energy levels, which were also considered to be introduced by defects, were dominant and weakened the effects of the shallow energy levels. Increase in the concentration of the deep trapping levels resulted in gradual decrease of the signal amplitude and degradation in the energy resolution. The peak for the alpha particles was obtained up to 5.5 × 10¹³ n/cm².     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

Decrease in alkaline triglyceride lipase in primary cultured hepatocytes from mice with sarcoma 180

Primary cultured hepatocytes from normal mice and mice with Sarcoma 180 were characterized. The viability of freshly isolated heptocytes from both sources was over 90% and the cells had a relatively stable population of DNA for a minimum of three days. After incubation with (³H)leucine, the syntheses and secretions of (³H)labeled trichloracetic acid-insoluble materials by hepatocytes from both normal and tumor-bearing mice increased similarly. However, the alkaline triglyceride lipase activity of a homogenate of freshly isolated hepatocytes from tumor-bearing mice was one-third that of cells from normal mice. the activity of hepatocytes from tumor-bearing mice inceeased less during culture than did the activity of cells isolated from normal mice.     

The combined method: a novel access technique for fetal endoscopic surgery

BACKGROUND/PURPOSE: To develop practical and less invasive techniques for fetal endoscopic surgery, new methods of lifting the uterine wall to allow fetal surgery without maternal laparotomy were developed and assessed. METHODS: Fetal endoscopic surgical procedures, including tracheostomy and umbilical vascular cannulation, were performed using one of the three methods to enter the uterus without maternal laparotomy in pregnant goats (n = 6; 105 to 115 days' gestation): (1) direct uterine lifting with an air-cushion device; (2) indirect uterine lifting, in which the uterine wall was fixed to the maternal abdominal wall using balloon tip ports inserted percutaneously by Seldinger's method, then the maternal abdomen was lifted mechanically; and (3) combined method, in which low pressure CO2 (5 mm Hg for initial inflation and 2 mm Hg for maintenance) was insufflated into the uterus in addition to the indirect uterine lifting cited above. RESULTS: The direct uterine lifting caused massive injury of myometrium and uterine membranes. The creation of intrauterine space and the protection of the membranes were not accomplished effectively by the indirect uterine lifting only. The combined method provided the adequate intrauterine space and excellent endoscopic visibility for completion of the endoscopic procedures with minimal uterine injury. CONCLUSION: The fetal endoscopic surgery may be accomplished simply and safely by the combined method, a novel technique of uterine lifting to allow fetal surgery without maternal laparotomy.     

Novel B-ring modified combretastatin analogues: syntheses and antineoplastic activity

A series of B-ring modified combretastatin analogues were synthesized and their inhibitory activity against microtubule assembly, cytotoxic activity against Colon 26 adenocarcinoma cancer cell line were evaluated. Among these, pyridone derivative (19) showed strong antimitotic activity and cytotoxicity, along with excellent water-solubility.     

The Gmicro/500 superscalar microprocessor with branch buffers

The Gmicro/500, which features a RISC-like dual-pipeline structure for high-speed execution of basic instructions and represents a significant advance for the TRON architecture, is presented. Upwardly-object-compatible with earlier members of the Gmicro series, this microprocessor uses resident dedicated branch buffers to greatly enhance branch instruction execution speed. Its microprograms simultaneously use dual execution blocks to execute high-level language instructions effectively. Fabricated with a 0.6-μm CMOS technology on a 10.9-mm×16-mm die, the chip operates at 50/66 MHz and achieves a processing rate of 100/132 MIPS     

Preparation of TiB2 sintered compacts by hot pressing

A sintered compact of titanium diboride (TiB₂) was prepared by hot pressing of the synthesized TiB₂ powder, which was obtained by a solid-state reaction between TiN and amorphous boron. Densification of the sintered compact occurred at 20 MPa and 1800° C for 5 to 60 min with the aid of a reaction sintering, including the TiB₂ formation reaction between excess 20 at % amorphous boron in the as-synthesized powder (TiB₂ + 0.2B) and intentionally added 10 at % titanium metal. A homogeneous sintered compact of a single phase of TiB₂, which was prepared by hot pressing for 30 min from the starting powder composition [(TiB₂ + 0.2B) + 0.1 Ti], had a fine-grained microstructure composed of TiB₂ grains with diameters of 2 to 3 m. The bulk density was 4.47 g cm^–3, i.e. 98% of the theoretical density. The microhardness, transverse rupture strength and fracture toughness of the TiB₂ sintered compact were 2850 kg mm^–2, 48 kg mm^–2 and 2.4 MN m^–3/2, respectively. The thermal expansion coefficient increased with increasing temperature up to 400° C and had a constant value of 8.8 x 10^–6 deg^–1 above 500° C.     

Effect of grain size on creep of Ti-53.4mol%Al intermetallics at 1100 K

Constant stress creep under compression stress, 100 to 316 MPa, at 1100 K was investigated on single-phase TiAl intermetallics. The material was ingot-cast, isothermally forged, and then annealed to produce stable equi-axed grain structures, whose average grain diameters were 25, 42 and 70m. Creep curves were very similar among the three specimens with different grain diameters and the creep rates at a given strain, as well as the minimum creep rates, depended little on grain size. Two regimes were observed on the stress dependence of the minimum creep rate. The stress exponent under high stresses was about 4.5, independent of grain size. Under stresses lower than about 150 MPa it became about 8.