Performance of the first Japanese large-scale facility for radon inhalation experiments with small animals

A radon test facility for small animals was developed in order to increase the statistical validity of differences of the biological response in various radon environments. This paper illustrates the performances of that facility, the first large-scale facility of its kind in Japan. The facility has a capability to conduct approximately 150 mouse-scale tests at the same time. The apparatus for exposing small animals to radon has six animal chamber groups with five independent cages each. Different radon concentrations in each animal chamber group are available. Because the first target of this study is to examine the in vivo behaviour of radon and its effects, the major functions to control radon and to eliminate thoron were examined experimentally. Additionally, radon progeny concentrations and their particle size distributions in the cages were also examined experimentally to be considered in future projects.     

Half-data-page insertion method for increasing recording density in angular multiplexing holographic memory

We have developed a method to use a half-size data page between two full-size data pages to increase the recording density in angular multiplexing holographic memory up to 1.5× as much as the conventional angular multiplexing sequence. In our recording sequence, the full- and half-size data pages are alternately multiplexed. This is because each plane wave from various points in a data page has different angular selectivity. A half-size data page has higher angular selectivity than a full-size data page. The required angular intervals were estimated by numerical simulation taking holographic medium tilt into account. Also, an angular multiplexing experiment using the half-data-page insertion method resulted in a low bit error rate of the order of 10(-3), which is sufficient for practical use.     

Measurement of cosmic-ray neutron dose onboard a polar route flight from New York to Seoul

Exposure to cosmic radiation in operation of a jet aircraft is considered to be a part of the occupational exposure. Cosmic radiation doses received in aviation are generally evaluated by numerical model simulations. The precision of the model calculation should be verified by measurements. From the viewpoint of radiological protection, neutrons are the most contributing radiation component and have to be precisely measured. Neutron measurements were thus performed in a long-haul flight using a relatively new transportable neutron monitor (WENDI-II) which responds fairly well to the cosmic-ray neutrons. The in-flight measurement was carried out on 5-6 November 2009 on a polar route flight from New York/John F. Kennedy airport to Seoul/Incheon airport. The flying time was ~14 h. The observations obtained as 1 cm ambient dose equivalent were compared with model calculations using a computer program developed by the authors for the calculation of aviation route doses 'JISCARD EX'. Good agreements between the measured and calculated values were observed over the polar route where the geomagnetic cut-off rigidity is the lowest.     

Effect of different copper fillers on the electrical resistivity of conductive adhesives

The effects of different copper fillers with different morphology and particle size have been studied in terms of electrical resistivity and thermal stability on the electrically conductive adhesives. The copper fillers used in this study were prepared by wet chemical reduction, electrolytic and gas atomization method, respectively. The as cured ECAs filled with different type of Cu fillers showed significant difference in electrical resistivity. Cu filler with smaller particle size showed higher packing density and larger surface area, which would enhance formation of conductive channels and increased conductive network in the ECAs, leading to a lower electrical resistivity. In addition, thermal stability of the ECAs were investigated under high temperature exposure at 125 °C and high humidity aging at 85 °C/85% RH for 1,000 h. Results showed that ECAs with Cu fillers of relatively small particle size and rough particle surface have excellent thermal stability due to enhanced adhesion and contact area between Cu fillers and the polymer matrix. A very low resistivity at an order of magnitude of 10^?4 ?? cm could be maintained for these ECAs after 1,000 h at 125 and 85 °C/85% RH.     

Environmental protection: researches in National Institute of Radiological Sciences

Some studies for radiological protection of the environment have been made at the National Institute of Radiological Sciences (NIRS). Transfer of radionuclides and related elements has been investigated for dose estimation of non-human biota. A parameter database and radionuclide transfer models have been also developed for the Japanese environments. Dose (rate)-effect relationships for survival, growth and reproduction have been investigated in conifers, Arabidopsis, fungi, earthworms, springtails, algae, duckweeds, daphnia and medaka. Also genome-wide gene expression analysis has been carried out by high coverage expression profiling (HiCEP). Effects on aquatic microbial communities have been studied in experimental ecosystem models, i.e., microcosms. Some effects were detected at a dose rate of 1 Gy day(-1) and were likely to arise from interspecies interactions. The results obtained at NIRS have been used in development of frameworks for environmental protection by some international bodies, and will contribute to environmental protection in Japan and other Asian countries.     

Vacuum seal for a rectangular flange

A new vacuum seal for a rectangular flange used in r.f. equipments, was developed. The vacuum seal consists of a recess with a flat surface, machined into a rectangular flange, a rectangular metal gasket with a raised projection on one face, and a mating flange with a recess and raised projection. No leak greater than 1 × 10⁻¹⁰ Pa m³/s was found in leak tests, before and after baking cycles (100 °C, 12 h).     

Fabrication and evaluation of nanostructure Al-SiCp composite by accumulative roll-bonding

A nanostructured Al/SiCp composite was fabricated by accumulative roll bonding (ARB) process. The amount of SiC particles introduced into aluminum sheet by one cycle ARB was 0.22 mg/cm2. Increment of the number of ARB cycles increased the amount of SiC particles and enhanced the homogeneity of the distribution of SiC particles. Microstructural change in aluminum matrix with proceeding of the ARB was very similar to that of the ARB-processed unreinforced aluminum; showing a dislocation cell and/or sub-grain structure in samples of lower ARB cycles and ultrafine grained structure in samples of higher ARB cycles. The variation of tensile strength with the ARB was also very similar to that of unreinforced aluminum. However, the effect of strengthening by the ARB was higher in the Al/SiCp composite than in unreinforced aluminum due to an existence of the SiC particles and the formation of finer grains.     

Influence of index table accuracy on roundness calibration in the multi-step method using monte carlo simulation

The precise and accurate roundness measurement is required year by year. The multi-step method is commonly used in the high-accuracy measurement for the roundness. The multi-step method is the self-calibration of the roundness capable of performing highly-advanced precise measurement. It depends on the reason that is able to separate measurement wave from the spindle rotation component and the form component of hemispherical master. But the mathematical models of the roundness measurement using that method are very complicated, describing numerous parameters and processes. So, recently, the Monte Carlo technique has attracted increasing attention as a very useful method for uncertainty estimation. This paper describes influences of the indexing angle accuracy and the noises generated by the roundness measuring machine, on the roundness measurements, both of which were analyzed by the Monte Carlo simulation. Furthermore, an example of hemispherical master is compared with the actual measurement data between when a reference guide plate is used utilizing the magnetic rotary encoder.     

Examination of the Mode II fracture behaviour of wood with a short crack in an asymmetric four-point bending test

Asymmetric four-point bending tests of agathis specimens with a short crack along the neutral axis in a tangential–longitudinal system were conducted onto analyse the failure behaviour of wood with a short crack. The nominal shear strength and Mode II critical stress intensity factors of the specimens with various crack lengths were measured, and the influence of crack length on these properties was examined. The nominal shear strength of the cracked specimens was significantly lower than the strength of a crack-free specimen, even when the crack was extremely short. This finding suggests that the fracture mechanics theory is effective for analysing the failure behaviour of wood with a very short crack in this loading condition. However, the Mode II critical stress intensity factor still depends on the crack length. When the crack length was corrected with considering the formation of fracture process zone ahead of the crack tip, the critical intensity factor could be predicted effectively as well as the nominal shear strength.     

Casting of organic glass by radiation-induced polymerization of glass-forming monomers at low temperature. II. Optical strain of remaining stress type

Previously it was found that casting could be carried out efficiently without strain formation by radiation-induced polymerization of glass-forming monomers. Two types of strain were observed in casting: thermal stream type, which was studied previously, and remained stress type. In this report, the effect of various factors on the formation of remaining stress-type strain in radiation-induced casting polymerization was studied. It was found that the molecular weight of prepolymer did not affect strain formation, while prepolymer concentration and viscosity of the system had a serious influence on strain formation. It could be deduced that this type of strain formed as a result of remaining inner stress due to poor relaxation of the shrinking stress. It was realized that less volume shrinkage of glass-forming monomers accompanying casting polymerization reduced the strain formation of this type in radiation-induced casting polymerization at low temperatures.