Breakdown Trade-Off Relation of Mechanical Properties via Micro-alloying in Mg–Mn Alloys

The impact of micro-alloying on tensile behavior at strain rates in various ranges is examined using five types of extruded Mg-0.3 at. pct Mn–0.1 at. pct X ternary alloys, where X is selected as a common element, Al, Li, Sn, Y or Zn. Microstructural observations reveal that the average grain size of these extruded alloys is between 1 and 3 μm, and these micro-alloying elements segregate at grain boundaries. In room temperature tensile and compression tests, these results show that the mechanical properties and deformation behavior are influenced by the micro-alloying element, even as a small addition of 0.1 at. pct. Mg–Mn–Y and Mg–Mn-Zn alloys show higher strength and smaller strain rate sensitivity (m-value) among the present alloys, owing to the rate-controlling mechanism as dislocation slip. On the other hand, the Mg–Mn–Li alloy exhibits the largest elongation to failure in tension and the highest strain rate sensitivity, associated with high contribution of grain boundary sliding to deformation. These differences are due to the grain boundary segregation of the micro-alloying elements. Compared to the common Mg alloys, the present ternary alloys also show a trade-off relationship between strength and ductility, which is similar to that of the well-known Mg alloys; however, these properties of the Mg–Mn system ternary alloys could be controlled via the type of micro-alloying elements with a chemical content of 0.1 at. pct.

     

Effects of bile acid feeding on hepatic deoxycholate 7α-hydroxylase activity in the hamster

In order to investigate the effects of bile acid feeding on hepatic microsomal deoxycholate 7α-hydroxylase activity, three different bile acids were administered (0.2% w/w in chow) to hamsters for two weeks. Deoxycholate 7α-hydroxylase activity was increased markedly by feeding of cholic acid (CA) and slightly by deoxycholic acid (DCA) Chenodeoxycholic acid (CDCA) had little effect on the enzyme activity. Feeding each of the bile acids significantly inhibited the activity of cholesterol 7α-hydroxylase in the order CDCA≥ DCA>CA. There was no correlation between deoxycholate 7α-hydroxylase activity and cholesterol 7α-hydroxylase activity. It is concluded that the activity of deoxycholate 7α-hydroxylase is up-regulated by feeding DCA and CA and that the mechanism seems to be different from that of cholesterol 7α-hydroxylase. The increased activity of hepatic deoxycholate 7α-hydroxylase by CA and DCA should be beneficial in minimizing the toxic effects of DCA in the hamster.     

Simple chemical syntheses of TAG monohydroperoxides

For the purpose of synthesizing standards to be used in the quantification of TAG hydroperoxides, three TAG (1,2-dioleoyl-3-palmitoylglycerol, 1-oleoyl-2-linoleoyl-3-palmitoylglycerol, and triolein) monohydroperoxides were chemically synthesized as authentic specimens. TAG were prepared by using a simple condensation in pyridine of glycerol and the corresponding acid chlorides. These TAG were then converted into monohydroperoxides by a photosensitized peroxidation. The synthesized monohydroperoxides were analyzed by normal-phase and RP-HPLC. The results of normal-phase HPLC analysis showed that monohydroperoxides from a corresponding TAG were a mixture of regioisomers. In RP-HPLC, however, the regioisomers of monohydroperoxides were not separated and gave a single peak, which may improve the sensitivity for the detection of TAG monohydroperoxides. In this study TAG monohydroperoxide standards were synthesized; these will be useful for the study of yet unknown biological and pathological roles of TAG hydroperoxides.     

Concentration of acetic acid in sulfite pulp evaporation drain by reverse osmosis

The evaporation drain of sulfite pulp spent liquor contains few volatile fatty acids, most of which is acetic acid. The main objective of this study is to recover acetic acid as the concentrated solution (about 4%), which could be used as a culture medium of the yeast. As acetic acid can easily pass through the cellulose acetate membrane, SP drains neutralized by NaOH, NH₄OH and Ca(OH)₂ were used as the feed solutions. In all cases, concentration by reverse osmosis was successfully carried out provided the appropriate pretreatment was employed. The recovery of acetic acid was 95.6, 90.5 and 98.2% for Na-, NH₄-, and Ca-drain, respectively. In addition, the recovered (permeated) water may be used as an industrial one.     

Polymerization of 2-dibutylamino-1,3,5-triazine-4,6-dithiol on wire during friction process

2-Dibutylamino-1,3,5-triazine-4,6-dithiol (DB) and a mixture of DB and triallylisocyanurate (TAIC) were used as a lubricant during steel wire drawing due to a dry process. DB gave a polymer film with 180 nm in thickness to wire surfaces during the wire drawing. The polymer film had a disulfide structure on the backbone and contained a small amount of DB monomer and olygomer. Molecular weight and polymer weight increased with the drawing rate. The mixture of DB and TAIC gave mainly a three-dimensional polymer film with 225 nm in thickness to wire surfaces during drawing. The polymer film insoluble in THF had mono and disulfide structures and contained a small amount of linear polymer, DB, and TAIC. Such tribological polymerizations are estimated as follows: DB produces dithiyl radicals on a nascent surface formed during drawing and in the presence of oxygen and heat. The dithiyl radicals were polymerized by coupling with each other to give disulfide bonds or added to allyl groups in TAIC to give monosulfide bonds. It is concluded that this technique should be possible to use for unifying metal processing and surface treatment. © 1995 John Wiley & Sons, Inc.     

The European,Japanese and US protective helmet,gloves and boots for firefighters: thermoregulatory and psychological evaluations

The purpose of this study was to investigate the physiological and subjective responses of the European, Japanese (JPN) and US firefighters' helmet, gloves and boots for international standardisation. Three experimental conditions were evaluated (clothing mass: 9.4, 8.2 and 10.1 kg for the three conditions, respectively) at the air temperature of 32°C and 60% relative humidity. The results showed that there was no significant difference among the three conditions in oxygen consumption, heart rate, total sweat rate, rectal temperature and mean skin temperature, whereas peripheral temperatures and subjective perceptions were lower in the JPN condition than in the other conditions (P < 0.05). These results indicate that a 0.5-kg reduction in helmet mass and a 1.1-kg reduction in boot mass during exercise resulted in a significant decrease in head and leg temperatures and subjective perceptions, while a 1.9-kg reduction in total clothing mass had insignificant influences on the metabolic burden and overall body temperature.     

Comparative study on the preparation and properties of radiation‐grafted polymer electrolyte membranes based on fluoropolymer films

In this study the fluoropolymers, poly(ethylene‐co‐tetrafluoroethylene) (ETFE) and poly(vinylidene fluoride) (PVDF) films, together with the radiation‐induced crosslinked polytetrafluoroethylene (cPTFE) film were compared on the basis of their preparation and properties of radiation‐grafted polymer electrolyte membranes. The polymer electrolyte membranes were prepared by radiation grafting of styrene into the base films and subsequent sulfonation. The proton conductivity and chemical stability of the three types of membranes with a similar ion exchange capacity (IEC) near 1.0 mmol/g were investigated and are discussed in detail. Although the ETFE‐based polymer electrolyte membrane was relatively more stable, its proton conductivity was lower than those of the PVDF‐ and cPTFE‐based membranes. On the other hand, the cPTFE‐based membrane showed a significantly higher proton conductivity, but its chemical stability was shorter than that of the ETFE‐based membrane. It is considered that the difference in the preparation and properties of the polymer electrolyte membranes was due to the difference in the degree of crystallinity as well as in the chemical structure of the fluoropolymer base films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1966–1972, 2007     

Fabrication and Microstructure Characterization of Ti3SiC2 Synthesized from Ti/Si/2TiC Powders Using the Pulse Discharge Sintering (PDS) Technique

Ti/Si/2TiC powders were prepared using a mixture method (M) and a mechanical alloying (MA) method to fabricate Ti₃SiC₂ at 1200°–1400°C using a pulse discharge sintering (PDS) technique. The results showed that the Ti₃SiC₂ samples with <5 wt% TiC could be rapidly synthesized from the M powders; however, the TiC content was always >18 wt% in the MA samples. Further sintering of the M powder showed that the purity of Ti₃SiC₂ could be improved to >97 wt% at 1250°–1300°C, which is ∼200°–300°C lower than that of sintered Ti/Si/C and Ti/SiC/C powders using the hot isostatic pressing (HIPing) technique. The microstructure of Ti₃SiC₂ also could be controlled using three types of powders, i.e., fine, coarse, or duplex-grained, within the sintering temperature range. In comparison with Ti/Si/C and Ti/SiC/C mixture powders, it has been suggested that high-purity Ti₃SiC₂ could be rapidly synthesized by sintering the Ti/Si/TiC powder mixture at relatively lower temperature using the PDS technique.     

Effect of metallic ions in photo-induced graft copolymerization onto cellulose

In photo-induced graft copolymerization of methyl methacrylate onto cellulose, the effect of metallic ions as sensitizer was investigated. Some metallic ions were effective in their adsorbed states and accelerated the formation of grafts in the order Fe²⁺ > Ag⁺ > Fe³⁺. However, Cu²⁺ acted negatively, and little effect was observed for Co²⁺, Ni²⁺, Mn²⁺, Zn²⁺, and Cr³⁺. In the systems in which aqueous metallic salt solutions were added, the formation of grafts was generally depressed, but Fe³⁺ was an exception. The effect of metallic ions on the scission reaction of cellulose main chains did not necessarily agree with the effect on the formation of grafts. This is attributed to the varied interaction between cellulose and the different active species produced by irradiation, depending on the type of metallic ions used.     

Graft copolymerization to cellulose. Effect of sodium thiosulfate on hydrogen peroxide initiator system

The effect of sodium thiosulfate on the graft copolymerization of methyl methacrylate to cellulose in the hydrogen peroxide initiator system was investigated. The addition of sodium thiosulfate in general was effective for decreasing the per cent grafting and the average molecular weight of grafts and increasing the formation of homopolymer, and the effects became pronounced with increasing hydrogen peroxide concentration. Moreover, the addition of sodium thiosulfate slightly suppressed the formation of grafts at a hydrogen peroxide concentration of 3 mmole/l., but greatly promoted it at 20 mmole/l. Traces of metallic ions present in cellulose could not be eliminated sufficiently by treatment with 3N hydrochloric acid. Such ions were found to interact with hydrogen peroxide and thus participate directly in the initiation and termination of the polymerization reaction. EDTA, the chelating agent, was highly effective for suppressing such participation of metallic ions. In the hydrogen peroxide initiator system applied to the EDTA-treated samples, sodium thiosulfate caused an effective initiation of graft formation.