Dual frequency open-loop electric potential microscopy for local potential measurements in electrolyte solution with high ionic strength

Recent development of open-loop electric potential microscopy (OL-EPM) has enabled to measure local potential distribution at a solid/liquid interface. However, the operating environment of OL-EPM has been limited to a weak electrolyte solution (<1 mM). This has significantly limited its application range in biology and chemistry. To overcome this limitation, we have developed dual frequency (DF) mode OL-EPM. In the method, an ac bias voltage consisting of two frequency components at f(1) and f(2) is applied between a tip and sample. The local potential is calculated from the amplitudes of the f(1) and |f(1) - f(2)| components of the electrostatic force. In contrast to the conventional single frequency (SF) mode OL-EPM, the detection of the 2f(1) component is not required in DF mode. Thus, the maximum bias modulation frequency in DF mode is twice as high as that in SF mode. The high bias modulation frequency used in DF mode prevents the generation of electrochemical reactions and redistribution of ions and water, which enables to operate OL-EPM even in a strong electrolyte solution. In this study, we have performed potential measurements of nanoparticles on a graphite surface in 1 and 10 mM NaCl solution. The results demonstrate that DF mode OL-EPM allows measurements of local potential distribution in 10 mM electrolyte solution.     

High-intensity multi-bunch beam generation by a photo-cathode RF gun

A multi-bunch photo-cathode RF gun system has been developed as an electron source for the production of intense quasi-monochromatic X-rays based on inverse Compton scattering. The desired multi-bunch beam is 100 bunches/pulse with a total charge of 500 nC and a bunch spacing of 2.8 ns. We modified the gun cavity of a ‘BNL-type IV’ RF gun to allow a CsTe cathode plug in the end plate. The system uses a four-dipole chicane beam line to allow the injection of laser light normal to the cathode surface. We compensate the gun cavity beam loading caused by the high-intensity multi-bunch electron beam by injecting the laser pulse before RF power has filled the cavity. We have achieved a total intensity of 220 nC in 100 bunches with a bunch-to-bunch energy spread under 1.3% (peak-to-peak). This paper concentrates on experiments to generate the high-intensity multi-bunch beam with compensation of the bunch-to-bunch energy spread due to heavy beam loading.     

Oxygen permeation properties and surface modification of acceptor-doped CeO2/MnFe2O4 composites

The preparation and oxygen permeation properties of the (Ce_0.8Pr_0.2)O_2−δ − x vol% MnFe₂O₄ composites, where x = 0 to 35, have been investigated. The samples were prepared by the Pechini method. In the case of Ce_0.8Pr_0.2O_2−δ, an oxygen flux density of 6 μmol⋅cm⁻²⋅s⁻¹ (L = 0.0247 cm) and the maximum methane conversion of 50% were attained at 1000^∘C. Unlike composites consisting of Gd-doped CeO₂ and MnFe₂O₄, the oxygen permeability of the (Ce_0.8Pr_0.2)O_2−δ – x vol% MnFe₂O₄ composites was almost constant regardless of the volume fraction of MnFe₂O₄; however, the optimum volume fraction of MnFe₂O₄ was determined to be 5 to 25 in the context of the chemical and mechanical stabilities under methane conversion atmosphere. In addition, the surface modification of the (Ce_0.8Gd_0.2)O_2−δ – 15 vol% MnFe₂O₄ composite was performed by using the FePt nanoparticles. The catalyst loading of 2.8 mg/cm² on the both side of the 0.3 mm-thick (Ce_0.8Gd_0.2)O_2−δ – 15vol% MnFe₂O₄ composite increased the oxygen flux density from 0.30 to 0.76 μmol⋅cm⁻²⋅s⁻¹ in the case of He/air gradients; however, the effect seems to be reduced in the case of high oxygen flux density caused by a large pO₂ gradient. Moreover, the Langmuir-Blodgett film of the FePt nanoparticles were successfully prepared on the tape-cast (Ce_0.8Gd_0.2)O_2−δ – 15vol% MnFe₂O₄ composite. Hydrophobic treatments for the surface of the composite were crucial to achieve high transfer ratio for the deposition of the LB film.     

New complementary logic circuits using coupled open quantum systems

This paper present new complementary logic circuits that exploit an intrinsic bistability in nanoscale coupled open quantum systems such as wells and wires. When operated with a multiple-phase split-level clocking scheme, the device can latch a binary digit while meeting gain, tolerance, and I/O decoupling requirements at the same time, which was difficult with conventional back-to-back negative differential resistance devices. This same structure in a dual-rail configuration can function as a complete set of classical logic circuits by changing only the connections of the input signals. When these circuits are combined to form a sequential circuit, low power operation is expected, thanks to better voltage scaling, a zero-standby-power equalized state, and efficient charge recycling.     

Combinatorial pulsed laser deposition and thermoelectricity of (La1−xCax)VO3 composition-spread films

La_1−xCa_xVO₃ composition-spread film library was fabricated by combinatorial pulsed laser deposition and their thermoelectric properties were evaluated paralelly by the multi-channel probes of Seebeck coefficient and electric conductivity. Concurrent X-ray analysis verified the formation of solid soluted films in the full composition range (0x1) as judged from the linear variation of the lattice constants. The Seebeck coefficients of La_1−xCa_xVO₃ changed from a large negative value to almost zero with the increase of x, due presumably to the variation of valence in vanadium ions.The power factor in this library was as high as 0.6 μW/cm K², which was obtained at x=0, i.e. pure LaVO₃ grown at 800 °C.     

Adaptive fuzzy inference neural network

An adaptive fuzzy inference neural network (AFINN) is proposed in this paper. It has self-construction ability, parameter estimation ability and rule extraction ability. The structure of AFINN is formed by the following four phases: (1) initial rule creation, (2) selection of important input elements, (3) identification of the network structure and (4) parameter estimation using LMS (least-mean square) algorithm. When the number of input dimension is large, the conventional fuzzy systems often cannot handle the task correctly because the degree of each rule becomes too small. AFINN solves such a problem by modification of the learning and inference algorithm.     

Application of an ultrahigh-resolution scanning electron microscope (UHS-T1) to biological specimens

In 1985 we developed an ultrahigh-resolution scanning electron microscope with a resolution of 0.5 nm. It is equipped with a field emission gun and an objective lens with a very short focal length. In this study we report a survey of some different preparation techniques and biological specimens using the new scanning electron microscope. Intracellular structures such as cell organelles were observed surprisingly sharper than those observed by ordinary scanning electron microscopes. However, at magnifications over 250,000 X, platinum particles could be discerned as scattered pebbles on the surface of all structures in coated materials. Using an uncoated but conductively stained specimen, we successfully observed ribosomes on a rough endoplasmic reticulum at a direct magnification of 1 million. In these images some protrusions were recognized on the ribosomes. Ferritin and immunoglobulin G were used as samples of biological macromolecules. These samples were observed without metal coating and conductive staining. The ferritin particles appeared as rounded bodies without any substructure on the surface and immunoglobulin G as complexes of three-unit bodies. In the latter the central body might correspond to the Fc fragment and two side ones to Fab fragments. We assume that ultrahigh-resolution scanning electron microscopy is an effective means for observation of the cell fine structures and biological macromolecules. It will open a new research field in biomedicine.