EC与~（99m）Tc－GH之间的配体交换反应动力学研究

实验表明，ＥＣ浓度与配体交换反应速度常数无关，体系的ｐＨ值对速度常数和９９ｍＴｃ－ＥＣ的标记率影响较大。测定并计算了不同ｐＨ值的交换反应速度常数。结果表明，为保证用配体交换法制备９９ｍｃ－ＥＣ时９９ｍｃ－ＥＣ的标记率大于９０％，体系的ｐＨ值必须≥８。     

用CAXA电子图板求解冲模压力中心

在模具设计中 ,冲裁模压力中心通常采用解析法或图解法求解。本文提出一种用CAXA绘图软件在设计制图时直接求解的方法 ,快速直接 ,简单方便 ,精度较高。     

环氧氯丙烷下游产品生产现状及市场前景

论述了环氧氯丙烷的主要下游产品环氧树脂、合成甘油、氯醇橡胶等的生产现状、市场前景等,指出:我国氯碱行业应该重视这些环氧氯丙烷下游精细化工产品的开发,以促进我国环氧氯丙烷的发展。     

Influence of volatile matter and deposited carbon on coke yield from coals

The relations between coke yields and the volatile matter content of 30 individual and 30 blended coals were investigated. Coke yields and deposited carbon related to volatile matter content can be expressed in the following equations: CY (%) = 97.89?0.86 VMch+VMc; and DC (%)= ?2.24+0.16 VMch; where: CY=real coke yield; VMch = volatile matter content of charging coal; VMc=volatile matter content of coke, and in the case of <2%; DC = deposited carbon. The test results show excellent correlation with practice.     

如何提高预焙铝电解槽阳极质量

预焙阳极的质量已严重制约铝电解技术的发展，必须予以足够的重视．国外在提高阳极质量方面的有效措施，可以供国内阳极工厂技术改造及科研攻关借鉴．     

氯化聚丙烯改性胶粘剂的合成及粘附性能研究

以甲苯为溶剂，过氧化二苯甲酰(BP0)为引发剂，通过自由基聚合，采用甲基丙烯酸羟乙酯(HEMA)和苯乙烯(St)接枝改性氯化聚丙烯(CPP)。研究了不同苯乙烯用量、不同反应温度、不同反应时间、不同引发剂用量对改性氯化聚丙烯胶粘剂粘附性能的影响，得出较佳的工艺条件为反应温度90℃，反应时问2h，原料配比m(CPP)：m(HEMA)：m(St)：m(BPO)=50：0．5：0．6：0．15。     

D301树脂分离衣康酸的工艺研究

采用弱碱性阴离子交换树脂Ｄ３０１对发酵法生产的衣康酸进行了分离研究。通过静态交换实验，研究了Ｄ３０１树脂对衣康酸的静态交换动力学，确定了传质机制和影响因素；通过动态交换实验，研究了以硫酸为洗脱剂，以氨水为再生剂的工艺过程，确定了主要工艺参数。     

Poly(3‐chlorothiophene) films prepared by the direct electrochemical oxidation of 3‐chlorothiophene in mixed electrolytes of boron trifluoride diethyl etherate and sulfuric acid

3‐Chlorothiophene (CT) was electrochemically polymerized in mixed electrolytes of a boron trifluoride diethyl etherate solution containing 0–20% (by volume) sulfuric acid. The oxidation potentials of the monomer in these media were measured to be only 1.06–1.31 V (vs Ag/AgCl). These values were much lower than that of CT in acetonitrile and 0.1 mol/L (Bu)₄NBF₄ (1.92 V vs Ag/AgCl). Poly(3‐chlorothiophene) (PCT) films with conductivities of 0.1–2 S cm^?1 were obtained. The structure, morphology, and electrochemical behavior of the PCT films also were investigated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 502–509, 2003     

Strain-induced crystallization,Part IV: Induction time analysis

The empirical equation, 1/t_i = Ae^Ei/RT, which expresses the exponential dependence of the reciprocal of crystallization induction time, t_i, has been analyzed and shown to be equivalent to the nucleation rate equations derived earlier in Part III (1). Consequently we have used the t_i measurements obtained earlier by Krueger and Yeh to calculate not only the nucleation rate enhancements but also the melting point elevations, the relative crystal thickness changes and molecular coil extension ratios of shear-crystallization polyethylene. It is shown that polyethylene when crystallized between 129 and 131°C at shear rates between 1.56 and 9.70 sec^?1 can have melting point increases of 4.2 to 7.2°C and crystal thickness decreases of 20 to 25 percent, when compared to those crystallized at 130°C in the quiescent state. The predicted “coil” extension in the melt just prior to shear-induced crystallization ranges between 21 and 36 percent. The results of these analyses as well as those on nucleation rates of polyethylene oxide are discussed in detail.