HN型催化剂催化α——蒎烯制苎烯的初步研究

本文用ＨＮ型催化剂低温催化α－蒎烯异构化制苎烯，考察了反应温度、反应时间、催化剂种类对反应结果的影响。实验结果表明在７０℃、反应４ｈ以上，苎烯的选择性仍保持在３５％以上。     

二安替吡啉甲烷--变色酸分光光度法分析陶瓷中的钛

介绍了一种高选择性、精密度较好的快速分析陶瓷中钛方法。在酸性介质中,变色酸(XK)、二安替吡啉甲烷(IIAM)两种试剂与钛共同作用形成三元络和物,三元络合物最大吸收位于510nm处,摩尔比为Ti:XK:IIAM=1:2:2,是测定陶瓷中钛的快速分析方法。     

Preparation of solar selective absorbing CuO coating for medium temperature application

A new method of preparing CuO solar selective absorbing coating for medium temperature is presented. After pretreatment, brass was overlaid with CuO by chemical plating. The effects of reactant concentration, reaction temperature and reaction time on the absorptivity of CuO coating were investigated. The optimized condition of preparing CuO coating was obtained. The CuO coating was analyzed with X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). In order to prolong the period of use, the CuO coating was protected by TiO₂. The experiment shows that the TiO₂/CuO coating is more heat-resistant, acid-resistant, and wear resistant than CuO coating, without losing absorptivity markedly. The TiO₂ coating can reduce emissivity and protect the CuO coating. Translated from Journal of Tianjin University, 2006, 39(12): 1485–1489 [译自: 天津大学学报]     

Preparation of fluoroacrylate nanocopolymer by miniemulsion polymerization used in textile finishing

Latex based on fluoroacrylate (TAN) and other comonomers was prepared via miniemulsion polymerization in the presence of stearyl trimethyl ammonium chloride (STAC) and 2, 2′‐azobis (2‐amidinopropane) dihydrochloride (ABAP) as a water soluble initiator. Light transmittance studies demonstrated that the light transmittance of prepared emulsions increases with the amount of TAN, STAC, cosolvent DPM, and hydrophobe DM. Given suitable reaction temperature and quantities of TAN, STAC, DPM, and DM, a copolymer emulsion of fluoroacylate with a particle size of 50 nm was produced. The water repellency tested on polyester fabrics displayed greater effectiveness than that of commercial products with higher fluorine content. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1466–1472, 2004     

Effect of ethylene-propylene copolymer with residual PE crystallinity on mechanical properties and morphology of PP/HDPE blends

Morphology and mechanical properties of polypropylene (PP)/high density polyethylene (HDPE) blends modified by ethylene-propylene copolymers (EPC) with residual PE crystallinity were investigated. The EPC showed different interfacial behavior in PP/HDPE blends of different compositions. A 25/75 blend of PP/HDPE (weight ratio) showed improved tensile strength and elongation at break at low EPC content (5 wt %). For the PP/HDPE = 50/50 blend, the presence of the EPC component tended to make the PP dispresed phase structure transform into a cocontinuous one, probably caused by improved viscosity matching of the two components. Both tensile strength and elongation at break were improved at EPC content of 5 wt %. For PP/HDPE 75/25 blends, the much smaller dispersed HDPE phase and significantly improved elongation at break resulted from compatibilization by EPC copolymers. © 1995 John Wiley & Sons, Inc.     

Acrylonitrile-based copolymer membranes containing reactive groups: Surface modification by the immobilization of biomacromolecules

Asymmetric membranes fabricated from poly(acrylonitrile-co-maleic acid) (PANCMA) were immobilized with heparin and/or insulin to improve their surface properties. These biomacromolecule-immobilized PANCMA membranes were prepared by the amination of the membrane surface with ethylenediamine, followed by the reaction of the amino groups with heparin and/or insulin in the presence of 1-ethyl-3-(3-dimethyl amidopropyl) carbodiimide. The surface-modified membranes were analyzed by X-ray photoelectron spectroscopy to confirm the immobilization of the biomacromolecules. Morphological changes on the membrane surface and in the cross section were characterized by scanning electron microscopy. The surface hydrophilicity and hemocompatibility of the studied membranes were evaluated on the basis of water contact angle, platelets adhesion and cell attachment measurements. It was found that, after the immobilization of the biomacromolecules, the water contact angle and the amount of adhered platelets and macrophages on the membrane decreased significantly when compared with the nascent ones, indicating the improvement of surface hydrophilicity. Furthermore, the heparin immobilized membrane showed the best hemocompatibility among the corresponding membranes studied.     

2,4,6-三溴苯胺对环氧树脂固化物阻燃耐热性的影响

用氧指数 (LOI) ,TG法测定研究了 2 ,4,6-三溴苯胺 (TBA)对环氧树脂酸酐固化物阻燃耐热性的影响 ,结果表明 TBA能较好地阻燃树脂固化物 ,TBA与 Sb2 O3 和磷酸三苯酯 (TPP)配用时具有阻燃协同效应 ,且对环氧树脂酸酐固化物的热稳定性影响较小。     

CrAPO-5和CrAPSO-5的合成及对环己烷氧化的研究

以三乙胺为模板剂，在合成过程中直接加入了硝酸铬及硅溶胶，水热合成了CrAPO-5和CrAPSO-5杂原子磷铝分子筛。以丙酮为溶剂，过氧化氢为氧化剂，考察了环己烷氧化制取环己酮的反应。反应12h、n(H2O2)／n(C6H12)=1．0、催化剂通量0．01-0．05g，环己烷的转化率最高可达到11．0％，酮醇比可达到1．39。     

Plasma graft polymerization of acrylamide onto crosslinked HTPB based PU membrane for pervaporation

Pervaporation of water-ethanol mixtures through plasma graft polymerization of acrylamide onto crosslinked hydroxyl terminated poly-butadiene (HTPB) based PU membranes, plasma graft polymerization of acrylamide onto crosslinked PU membrane (AAm-p-CPU), were investigated. The grafting was dependent on the discharge power and pretreatment period. The effects of crosslinking, plasma treatment conditions, feed compositions, and feed temperature on the performance of these membranes were studied. The physical properties of crosslinked membrane were better than those of the uncrosslinked membrane. In addition, compared with crosslinked PU membranes (CPU), the plasma modified crosslinked PU membranes effectively improve the pervaporation separation performances.     

气相色谱法测定石脑油中含氧化合物含量

本文论述了利用气相色谱法检测石脑油中含氧化合物的方法,考察了无阀切换技术、分离模式的设计、操作条件的优化等方面的问题。提出利用多维气相色谱法,采用一根非极性柱和一根极性柱进行独立和串联分离,通过改变辅助载气压力的无阀切换方式进行柱分离,应用双FID检测器进行信号检测,数据利用Agilent的chemestation工作站采集和输出。该方法操作简单,分析时间在23 min以内,重复测定结果的相对标准偏差(RSD)小于1.5%,标准加入回收率在95～105%范围内,方法准确可靠。