Coupled shear‐flexural model for dynamic analysis of fixed‐base tall buildings with tuned mass dampers

An equivalent discrete model is developed for time domain dynamic analysis of uniform high‐rise shear wall‐frame buildings with fixed base and carrying any number of tuned mass dampers (TMDs). The equivalent model consists of a flexural cantilever beam and a shear cantilever beam connected in parallel by a finite number of axially rigid members that allow the consideration of intermediate modes of lateral deformation. The proposed model was validated by a building whose lateral resisting system consists of a combination of shear walls and braced frames. The results showed the effectiveness of TMDs to reduce the peak displacements, interstory drift ratio, and accelerations when the building is subjected to a seismic load. The root mean square accelerations due to along‐wind loads also decrease if TMDs are attached to the building.     

Heavy Metals in Stream Sediments from the Coquimbo region (Chile): Effects of Sustained Mining and Natural Processes in a Semi-arid Andean Basin

Abstract.   Active sediments from the Elqui River in Chile were sampled 4 times at 10 sites during 2000. Concentrations of Ag, Ba, Cd, Co, Cr, Hg, Mn, Mo, Ni, Pb, Sr, Ti, V, Al, Ca, Fe, K, Mg, Na, P, and S were normal. Zinc levels were clearly high, and those of Cu (hundred to thousands ppm) and As (tens to hundreds ppm) were highly anomalous. Dissolved Cu (0.1-12.7 ppm) and Zn (0.2-2.2 ppm) levels were also very high. The anomalies of the upper tributaries are due to the El Indio–Tambo Au-Cu-As district and large hydrothermal alteration zones at altitudes between 3500–4500 m. Lower on the river, old and active tailing waste deposits and on-going mining operations in the Talcuna Cu (Pb) district are responsible. Partially eroded tailing deposits in the alluvial plain of the Elqui River and its tributaries, and especially in the El Indio-Tambo district, after mine closure in 2000, warrant special attention.     

Synthesis and characterization of poly (styrene‐b‐[(butadiene)1−x‐(ethylene‐co‐butylene)x] ‐b‐styrene) star‐like molecular polymers produced by partial hydrogenation of SBS

This article reports the synthesis and characterization of four arm star‐shaped poly(styrene‐b‐[(butadiene)_1?x‐(ethylene‐co‐butylene)_x]‐b‐styrene) (SBEBS) copolymers. A series of SBEBS copolymers with different compositions of the elastomeric block were produced by hydrogenating a given poly(styrene‐b‐butadiene‐b‐styrene) (SBS) copolymer using a catalyst prepared from bis(η⁵‐cyclopentadienyl)titanium(IV) dichloride and n‐butyllithium. The characterization was accomplished by proton nuclear magnetic resonance spectroscopy (¹H NMR), infrared spectroscopy (FTIR), gel permeation chromatography (GPC), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and thermogravimetric analysis (TGA). The results indicate that there is a selective saturation of the polybutadiene block over the polystyrene block; this selectivity was determined by the Ti/Li molar ratio and the concentration of Ti. It was observed that the saturation rate of the 1,2‐vinyl was higher than that of the 1,4‐trans and 1,4‐cis poly(butadiene)‐b isomers. The DSC and DMA results indicate that the degree of hydrogenation had a profound effect on the polymer's relaxation behavior. All samples exhibited a biphasic system behavior with two distinct transitions corresponding to the elastomeric and polystyrene blocks. SBEBS copolymers with higher saturation levels (>33%) exhibited a crystalline character. The TGA results indicated a characteristic weight loss temperature in all samples, with slightly higher thermal degradation stabilities in the materials with higher degrees of saturation. POLYM. ENG. SCI., 54:2332–2344, 2014. © 2013 Society of Plastics Engineers     

Synthesis of α‐cellulose/polypyrrole composite for the removal of reactive red dye from aqueous solution: Kinetics and equilibrium modeling

In this work, a composite from α‐cellulose coated with conducting polypyrrole by in situ polymerization using potassium persulfate as oxidant was obtained. The composite was characterized by fourier transform infrared (FTIR) spectroscopy, cyclic voltammetry, UV/Vis spectroscopy, and scanning electron microscopy (SEM) analysis showed homogeneous coating of α‐cellulose with polypyrrole (PPy) to produce a composite with a conductivity of 3.5 × 10⁻⁵ S/m. Batch aqueous adsorption experiments of the reactive red 120 (RR120) dye onto the synthesized material were conducted. The results showed that this composite is an efficient adsorbent for RR120 dye removal. For the adsorption experiments set to an initial pH of 3.9, the adsorption capacity was 15.6 mg of dye/g of composite for an equilibrium concentration (in the liquid) of RR120 dye equal to 1,000 mg/L, whereas a value of 96.1 mg of dye/g of composite was obtained when the solution pH was set to 2.0 for the same equilibrium concentration. When performing adsorption experiments using pure α‐cellulose, dye adsorption was insignificant at any pH value. Adsorption isotherm for RR120 was described by a typical Freundlich model. The transient adsorption of RR120 on the synthesized composite was described by a general three‐resistance model that includes the transport on the film that surrounds the composite particles, diffusion inside the particles, and adsorption on the surface of the particles. A fitting of the uptake curves was performed allowing the estimation of values for the effective diffusivity, D₀, and the adsorption rate coefficient, k₁. For the adsorption experiments with an initial pH value set to 3.9, D₀ was estimated as 1.05 × 10⁻¹⁰ m²/s, whereas k₁ was 1.65 × 10⁻⁴ Lⁿ/g mg^{n − 1} s; the corresponding values of k₁ at pH = 2 and 9.0 were 3.18 × 10⁻⁴ and 5.16 × 10⁻⁵, respectively. POLYM. COMPOS., 36:312–321, 2015. © 2014 Society of Plastics Engineers     

Carbon-Based Materials in Photodynamic and Photothermal Therapies Applied to Tumor Destruction

Within phototherapy, a grand challenge in clinical cancer treatments is to develop a simple, cost-effective, and biocompatible approach to treat this disease using ultra-low doses of light. Carbon-based materials (CBM), such as graphene oxide (GO), reduced GO (r-GO), graphene quantum dots (GQDs), and carbon dots (C-DOTs), are rapidly emerging as a new class of therapeutic materials against cancer. This review summarizes the progress made in recent years regarding the applications of CBM in photodynamic (PDT) and photothermal (PTT) therapies for tumor destruction. The current understanding of the performance of modified CBM, hybrids and composites, is also addressed. This approach seeks to achieve an enhanced antitumor action by improving and modulating the properties of CBM to treat various types of cancer. Metal oxides, organic molecules, biopolymers, therapeutic drugs, among others, have been combined with CBM to treat cancer by PDT, PTT, or synergistic therapies.     

Architectural survey of historical buildings: The orders of classical architecture in the Baptistery of Florence

The survey of historic buildings is very important for architectural conservation. An integral survey allows perpetuating the building historical memory, deciphering it for future generations, and recovering it in case of accidental loss. The Baptistery of Florence survey was done with four measuring methods: the “direct” one, which employs traditional measuring tools; the “indirect” one, which expedites the dimension-gathering process with more precision; and the “photogrammetric” one, which uses snapshots to facilitate the representation process with computers. An innovative measuring concept, known here as the “recovery survey”, synthetizes graphical reality so that irregularitiesddue to the project materialization and deterioration over timeddisappear; therefore, retrieving the building original design. Columns with their bases, shafts and capitals, as well as entablatures with their architraves, friezes and cornices were under study. The three Greek orders (Doric, Ionic and Corinthian) together with the two roman orders (Tuscan and Composite) unveiled the classical architecture significance. These constituents, which reoccur inside and outside the baptistery, were measured as part of these holistic survey and recovery process, to achieve the objective of this research study: the recording of this world historical building through an integral survey and rilievo to decode its significance and symbolism.     

Design and synthesis of foam glasses from recycled materials

Recycling has emerged as an environmental key point due to the diminishing of natural resources and the generation of ever-increasing amounts of industrial solid wastes. Glass wastes are among the materials that attract great interest in the recycling concept. This work presents the results of foams production from four series of compositions. The first series comprises powders of a sodium-calcium-silicate sheet glass cullet as the main component, an alkali-earth aluminosilicate glass as an additive, and a reagent grade silicon carbide (SiC) powder as gassing agent. In the second series, the glass cullet was used in combination with fly ashes (FLA) as main components, while SiC waste from abrasive paper served as foaming agent. In the third and fourth series, carbonates (calcite and dolomite) were used for foaming powder mixtures composed of sheet glass cullet and FLA, and powdered cathode ray tube panel glasses, respectively. All the processing parameters, including the main components, the nature and content of foaming agents are shown to play a crucial role on the foaming ability and final properties of the glass foams.