Lightweight porous silica foams with extreme-low dielectric permittivity and loss for future 6G wireless communication technologies

In the next generation wireless communication systems operating at near terahertz frequencies, dielectric substrates with the lowest possible permittivity and loss factor are becoming essential. In this work, highly porous (98.9% ± 0.1%) and lightweight silica foams (0.025 ± 0.005 g/cm3), that have extremely low relative permittivity (εr = 1.018 ± 0.003 at 300 GHz) and corresponding loss factor (tan δ< 3 × 10?4 at 300 GHz) are synthetized by a template-assisted sol-gel method. After dip-coating the slabs of foams with a thin film of cellulose nanofibers, sufficiently smooth surfaces are obtained, on which it is convenient to deposit electrically conductive planar thin films of metals important for applications in electronics and telecommunication devices. Here, micropatterns of Ag thin films are sputtered on the substrates through a shadow mask to demonstrate double split-ring resonator metamaterial structures as radio frequency filters operating in the sub-THz band.     

Electrical Resistance Tomography imaging of concrete

We apply Electrical Resistance Tomography (ERT) for three dimensional imaging of concrete. In ERT, alternating currents are injected into the target using an array of electrodes attached to the target surface, and the resulting voltages are measured using the same electrodes. These boundary measurements are used for reconstructing the internal (3D) conductivity distribution of the target. In reinforced concrete, the metallic phases (reinforcing bars and fibers), cracks and air voids, moisture gradients, and the chloride distribution in the matrix carry contrast with respect to conductivity. While electrical measurements have been widely used to characterize the properties of concrete, only preliminary results of applying ERT to concrete imaging have been published so far. The aim of this paper is to carry out a feasibility evaluation with specifically cast samples. The results indicate that ERT may be a feasible modality for non-destructive evaluation of concrete.     

Fabrication and properties of composites from BST and polypropylene-graft-poly(styrene-stat-divinylbenzene)

In this work, ceramic–polymer composites were fabricated from barium strontium titanate powder (BST) and polypropylene-graft-poly(styrene-stat-divinylbenzene) (ER) using a twin-screw extruder. The compounding process was characterized by rheological measurements. The effects of volume loading of BST on dielectric and mechanical properties were investigated. The dielectric properties were measured as a function of frequency and BST loading. For example, the relative permittivity and loss tangent (tan δ) of the BST–ER composites at 1 GHz were gradually increased from 2.4 and 0.0001 to 28.5 and 0.0085, respectively, as the loading was increased from 0 to 50.5 vol.%. Stearic acid (StA) was used as a surface-modifier of the BST. With an approximate surface coverage of 83%, an improvement in processability and a slight increase of the permittivity was observed, while tan δ remained low. The excellent dielectric characteristics of these composites, with high permittivity and low tan δ, make them attractive novel electronic materials for high frequency applications.     

Exact self-imaging of transversely periodic fields

Conditions for exactly self-imaging nonparaxial fields that are periodic also in the transverse direction are introduced. The theory is first derived by assuming full coherence and then extended into the domain of partial coherence. Different types of solutions are discussed, and some illustrations of the existence of solutions and intensity distributions of the fields are presented.     

Free-field characterization via directional transmission through a nanoaperture

We propose a scheme based on extraordinary transmission of light through a single nanoaperture, surrounded by periodic corrugations, for direct characterization of focal-region optical fields with subwavelength-scale structure. We describe the design of the device on the basis of rigorous diffraction theory and fabricate a prototype using a process that involves electron beam lithography, dry etching, and template stripping. First experimental results performed with a transmission-type confocal optical microscope demonstrate the potential of the method.     

Designing Fast Fourier Transform Accelerators for Orthogonal Frequency-Division Multiplexing Systems

Designing accelerators for the real-time computation of Fast Fourier Transform (FFT) algorithms for state-of-the-art Orthogonal Frequency-Division Multiplexing (OFDM) demodulators has always been challenging. We have scaled-up a template-based Coarse-Grain Reconfigurable Array device for faster FFT processing that generates special purpose accelerators based on the user input. Using a basic and a scaled-up version, we have generated a radix-4 and mixed-radix (2, 4) FFT accelerator to process different length and types of algorithms. Our implementation results show that these accelerators satisfy not only the execution time requirements of FFT processing for Single Input Single Output (SISO) wireless standards that are IEEE-802.11 a/g and 3GPP-LTE but also for Multiple Input Multiple Output (MIMO) IEEE-802.11n standard.     

Analysis of short fibres orientation in steel fibre-reinforced concrete (SFRC) by X-ray tomography

The mechanical properties of fibre composite materials are largely determined by the orientation of fibres within the matrix. Which orientation distribution short fibres follow in different parts of a structural element is still a subject for research and discussions in the scientific community. In this article, we present a modern and advanced method for measuring the orientation of short fibres in steel fibre-reinforced concrete (SFRC) by X-ray microtomography. With this method, a voxel image of the fibres is obtained directly in 3D, and the orientation of each individual fibre is calculated based on a skeletonized representation of this image. Scans of 12 SFRC samples, taken from the central height region of real-size floor slabs, reveal the fibres to be mostly horizontally oriented near the centre of a floor slab and more vertically oriented near the edge; here the alignment with the formwork dominates. The fibre orientation distributions are characterized by several orientation parameters as quantitative measures for the alignment. On the practical side, this method has the potential to be incorporated into the development and production process of SFRC structures to verify how the fibres contribute to capacity.     

Interactive multi-frame reconstruction for mobile devices

The small size of handheld devices, their video capabilities and multiple cameras are under-exploited assets. Properly combined, the features can be used for creating novel applications that are ideal for pocket-sized devices, but may not be useful in laptop computers, such as interactively capturing and analyzing images on the fly. In this paper we consider building mosaic images of printed documents and natural scenes from low resolution video frames. High interactivity is provided by giving a real-time feedback on the video quality, while simultaneously guiding the user’s actions. In our contribution, we analyze and compare means to reach interactivity and performance with sensor signal processing and GPU assistance. The viability of the concept is demonstrated on a mobile phone. The achieved usability benefits suggest that combining interactive imaging and energy efficient high performance computing could enable new mobile applications and user interactions.     

Enhancing perceived quality of compressed images and video with anisotropic diffusion and fuzzy filtering

Fuzzy filtering has recently been applied and optimized for reducing distortion in compressed images and video. In this paper, we present a method combining the powerful anisotropic diffusion equations with fuzzy filtering for removing blocking and ringing artifacts. Due to the directional nature of these artifacts, we have applied directional anisotropic diffusion. In order to improve the performance of the algorithm, we select the threshold parameter for the diffusion coefficient adaptively. Two different methods based on this approach are presented: one designed for still images and the other for YUV video sequences. For the video sequences, different filters are applied to luminance (Y) and chrominance (U,V) components. The performance of the proposed method has been compared against several other methods by using different objective quality metrics and a subjective comparison study. Both objective and subjective results on JPEG compressed images, as well as MJPEG and H.264/AVC compressed video, indicate that the proposed algorithms employing directional and spatial fuzzy filters achieve better artifact reduction than other methods. In particular, robust improvements with H.264/AVC video have been gained with several different content types.     

Bio‐hybrid nanocomposite coatings from sonicated chitosan and nanoclay

Nanocomposite films and coatings with improved properties were produced from ultrasonic dispersed chitosan and hydrophilic bentonite nanoclay. Bio‐hybrid coatings were applied onto argon–plasma‐activated LDPE coated paper. The intercalation of chitosan in the silicate layers was confirmed by the decrease of diffraction angles as the chitosan/nanoclay ratio increased. Nanocomposite films and multilayer coatings had improved barrier properties against oxygen, water vapor, grease, and UV‐light transmission. Oxygen transmission was significantly reduced under all humidity conditions. In dry conditions, over 99% reduction and at 80% relative humidity almost 75% reduction in oxygen transmission rates was obtained. Hydrophilic chitosan was lacking the capability of preventing water vapor transmission, thus total barrier effect of nanoclay containing films was not more than 15% as compared with pure chitosan. Because to very thin coatings (≤1 μm), nanoclay containing chitosan did not have antimicrobial activity against test strains. All coating raw materials were “generally recognized as safe” (GRAS) and the calculated total migration was in all cases ≤6 mg/dm², thus the coatings met the requirements set by the packaging legislation. Processing of the developed bio‐hybrid nanocomposite coated materials was safe as the amounts of released particles under rubbing conditions were comparable with the particle concentrations in a normal office environment. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010