Basic trends in development of drilling equipment for ore mining with block caving method

The authors have determined the causes of drop in performance of induced block caving using fans of blastholes 105 mm in diameter and single blastholes 250 mm in diameter, as well as the sources of increased drilling cost and expansion of start-up time of production blocks in Abakan underground mine. Alternatives of improvement in drilling efficiency under current conditions are discussed.     

Effects of Undercooling and Transformation Time on Microstructure and Strength of Fe–C–Mn–Si Superbainitic Steel

Strength of Materials - A metallographic method, dilatometry, and X-ray diffraction were applied to investigate the effects of undercooling and holding time on bainitic transformation,...     

In situ observation of synthesized nanoparticles in ultra-dilute aerosols via X-ray scattering

In-air epitaxy of nanostructures (Aerotaxy) has recently emerged as a viable route for fast, large-scale production. In this study, we use small-angle X-ray scattering to perform direct in-flight characterizations of the first step of this process, i.e., the engineered formation of Au and Pt aerosol nanoparticles by spark generation in a flow of N₂ gas. This represents a particular challenge for characterization because the particle density can be extremely low in controlled production. The particles produced are examined during production at operational pressures close to atmospheric conditions and exhibit a lognormal size distribution ranging from 5–100 nm. The Au and Pt particle production and detection are compared. We observe and characterize the nanoparticles at different stages of synthesis and extract the corresponding dominant physical properties, including the average particle diameter and sphericity, as influenced by particle sintering and the presence of aggregates. We observe highly sorted and sintered spherical Au nanoparticles at ultra-dilute concentrations (< 5 × 10⁵ particles/cm³) corresponding to a volume fraction below 3 × 10^–10, which is orders of magnitude below that of previously measured aerosols. We independently confirm an average particle radius of 25 nm via Guinier and Kratky plot analysis. Our study indicates that with high-intensity synchrotron beams and careful consideration of background removal, size and shape information can be obtained for extremely low particle concentrations with industrially relevant narrow size distributions.

     

Design of an Electromagnetic Frequency Tunned Antenna for Mobile Communications

Wireless Personal Communications - Current mobile communications technology relies heavily on efficient design of antennas, where the operational characteristics of the wireless communication...     

Sintering behaviour of fluorapatite–silicate composites produced from natural fluorapatite and quartz

In this work, the sintering behaviour of fluorapatite (FAp)–silicate composites prepared by mixing variable amounts of natural quartz (2.5 wt% to 20 wt%) and FAp was studied. The composites were pressureless sintered in air at temperatures from 1000 °C to 1350 °C. The effects of temperatures on the densification, phase formation, chemical bonding and Vickers hardness of the composites were evaluated. All the samples exhibited mixed phase, comprising FAp and francolite as the major constituents along with some minor phases of cristobalite, wollastonite, dicalcium silicate and/or whitlockite dependent on the quartz content and sintering temperature. The composite containing 2.5 wt% quartz exhibited the best sintering properties. The highest bulk density of 3 g/cm³ and a Vickers hardness of >4.2 GPa were obtained for the 2.5 wt% quartz–FAp composite when sintered at 1100 °C. The addition of quartz was found to alter the microstructure of the composites, where it exhibited a rod-like morphology when sintered at 1000 °C and a regular rounded grain structure when sintered at 1350 °C. A wetted grain surface was observed for composites containing high quartz content and was believed to be associated with a transient liquid phase sintering.     

High-Alumina Mixes Based on Molded Bauxite Suspensions

Refractories and Industrial Ceramics - Results of studying the rheotechnological properties of moldable refractory mixes based on bauxite suspensions plasticized with refractory clay are presented....     

Hydrogenation process in multiphase alloys of Ti-Zr-Mn-V system on the example of Ti42.75Zr27Mn20.25V10 alloy

The influence of phase composition and microstructure of Ti_42.75Zr₂₇Mn_20.25V₁₀ alloy on its hydrogenation kinetic and phase composition of hydrogenated product was studied. It is established that the process of dissociation of hydrogen molecules begins on the surface of Laves phase crystallites. The dissolution of atomic hydrogen in the material volume leads to the formation of cracks in the intermetallic crystallites, which further appear as additional centers of dissociation of hydrogen molecules and noticeably accelerate the diffusion of hydrogen into the bulk material. It was shown that the Laves phase acts as a donor of atomic hydrogen for the BCC solid solution during hydrogenation of two-phase structure, initiating intensive hydrogenation of the BCC phase at room temperature.     

Context-Based Path Prediction for Targets with Switching Dynamics

International Journal of Computer Vision - Anticipating future situations from streaming sensor data is a key perception challenge for mobile robotics and automated vehicles. We address the problem...     

An automated treatment planning strategy for highly noncoplanar radiotherapy arc trajectories

Radiation therapy is a technology-driven cancer treatment modality that has experienced significant advances over the last decades, due to multidisciplinary contributions that include engineering and computing. Recent technological developments allow the use of noncoplanar volumetric modulated arc therapy (VMAT), one of the most recent photon treatment techniques, in clinical practice. In this work, an automated noncoplanar arc trajectory optimization framework designed in two modular phases is presented. First, a noncoplanar beam angle optimization algorithm is used to obtain a set of noncoplanar irradiation directions. Then, anchored in these directions, an optimization strategy is proposed to compute an optimal arc trajectory. The computational experiments considered a pool of twelve difficult head-and-neck tumor cases. It was possible to observe that, for some of these cases, the optimized noncoplanar arc trajectories led to significant treatment planning quality improvements, when compared with coplanar VMAT treatment plans. Although these experiments were done in a research environment treatment planning software (matRad), the conclusions can be of interest for a clinical setting: automated procedures can simplify the current treatment workflow, produce high-quality treatment plans, making better use of human resources and allowing for unbiased comparisons between different treatment techniques.