Experimental evaluation of fatigue behaviour of thin Al5456 welded joints

Because of wide applications of welded structures in different industries, using design codes and standards such as IIW recommendations is known as a safe and common method to design welded joints. The weld geometry and thickness of welded joint are the most important parameters that affect the fatigue strength of welded joints. In the present study, the fatigue behaviour of thin Al5456 butt‐welded joints has been investigated, and the effect of thickness on fatigue strength has been evaluated. Contrary to the above‐mentioned recommendations about thin welded joints, it was shown that the thickness of welded joints affects the fatigue strength. Moreover, the fatigue test results have been compared with the IIW design recommendations for three well‐known approaches in order to analyse the reliability of the codes. According to the design stress‐life diagrams, it was found that in some cases, the fatigue strength has much larger values than the IIW predictions, and IIW‐based design causes an over conservative design. While in some other cases, the fatigue strength is lower than IIW recommendations, and it leads to a non‐conservative design. Based on the experimental results, the new values for slope of S‐N curve and FAT have been proposed in order to improve the design diagrams.     

A Multi-Model Nonstationary Rainfall-Runoff Modeling Framework: Analysis and Toolbox

Water Resources Management - We present a framework and toolbox for multi-model (one at a time) nonstationary modeling of rainfall-runoff (RR) transformation. The designed time-varying nature of...     

An analysis of characteristic discharges for the Adaim River (Iraq) in multiyear period

A major River Tigris tributary in Iraq, the Adaim River, has a Mediterranean river flow regime with a total basin area of 12,482 km². The river catchment responds almost immediately to rainfall with apparently minimum storage (i.e. flashy stream). The river daily hydrograph showed a daily peak flow of 1,476 m³/s with substantial seasonal and random variability; the flow duration curve followed the two‐parameter lognormal probability distribution. Gamma and the two‐parameter Weibull probability distributions fitted the monthly mean river discharge for the period 1937–2012 well. Normal and gamma probability distributions were found to appropriately describe the distribution of the annual mean river discharge for the same period. Gumbel extreme value, Log Pearson type III, and the two‐parameter lognormal distributions gave a reasonable fit to the annual maximum discharge record for the river. A regression formula was used to fit the annual minimum discharge record, which has a significant number of zero values. There was a positive and significant correlation (r = 0.77) between the annual mean discharge at the measuring site and seasonal rainfall measured at Karkuk meteorological station located in the north central part of the basin. The rainfall record at Karkuk showed a significant decline in seasonal rainfall after 1993.     

Distributed Adaptive Dynamic Surface Control for Synchronization of Uncertain Nonlinear Multi-agent Systems

In this paper a distributed adaptive dynamic surface controller is proposed for multi-agent systems under fixed directed graph topologies. The agents have uncertain nonlinear dynamics and are influenced by bounded unknown disturbances. The controller should synchronize the states of all agents with the corresponding states of the nonautonomous leader. It is proved that, with the proposed controller, the synchronization error remains bounded; and the bounds can be arbitrarily decreased by increasing the controller gains. The control rules are designed such that each agent only requires the state information of its neighbors, rendering a distributed control. The effectiveness of the proposed method is demonstrated through two simulation examples.     

New insights into nanoindentation crack initiation in ion‐exchanged sodium aluminosilicate glass

The effect of ion‐exchange on the fracture behavior and the threshold load is investigated for radial crack initiation resulting from cube‐corner indentation. Both tin and air sides of the sodium aluminosilicate float glass are considered. The threshold load and mechanical properties are experimentally measured by nanoindentation. A qualitative explanation of crack initiation is developed by analyzing the stresses at the indentation site. The ion‐exchanged glasses show a lower threshold load for radial crack initiation with a cube‐corner indenter than the raw glass, and this is due to a higher crack driving stress for ion‐exchanged glasses. However, the compressive stress on the surface of the ion‐exchanged glasses can inhibit the expanding of the radial cracks. The air side always shows higher values for the threshold load than the tin side before and after ion‐exchange, which is in accordance with the calculated crack driving stress results.     

Electrically conductive polycarbonate/ethylene‐propylene copolymer/multi‐walled carbon nanotubes nanocomposites with improved mechanical properties

In this article, the effect of Multi‐walled carbon nanotubes (MWCNTs) on the electrical conductivity and mechanical properties of polycarbonate (PC) toughened with cross‐linked ethylene‐propylene copolymer (EPC) was investigated. The solubility parameters of the PC and EPC were calculated using Hoy methods to clarify the miscibility of the polymer blends. It could be concluded that in the cooled state, the blends form a heterogeneous structure with two separate phases. The tensile, flexural, impact toughness properties of the PC/EPC blend and PC/EPC/MWCNT nanocomposites were carried out to illuminate the optimum concentration of polymer blends and MWCNTs. The 335% increment for the impact strength results appeared with combination of 10% EPC in the PC matrix. The flexural modulus and strength of PC/EPC blend increased by 75.1% and 59.1%, respectively. The Nielsen model was performed to fit the best curve of theoretical simulation to experimental results for elastomeric dispersed in the plastic matrix. Halpin‐Tsai model was applied to estimate the stiffness of nanocomposites blends with different volume fraction and aspect ratio of MWCNTs in the PC/EPC blends. Finally, in the presence of MWCNTs, all nanocomposite samples were semi‐conducting and the percolation threshold of the PC/EPC (10%) blends was between 0.5% and 1.0% MWCNTs. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44661.     

A New Method Modifying Single Miller Feedforward Frequency Compensation to Drive Large Capacitive Loads: Putting an Attenuator in the Path

A new method to compensate three-stage amplifier to drive large capacitive loads is proposed in this paper. Gain Bandwidth Product is increased due to use an attenuator in the path of miller compensation capacitor. Analysis demonstrates that the gain bandwidth product will be improved significantly without using large compensation capacitor. Using a feedforward path is deployed to control a left half plane zero which is able to cancel out first non-dominant pole. A three stage amplifier is simulated in a 0.18 μm CMOS technology. The purpose of the design is to compensate three-stage amplifier loading 1000 pF capacitive load. The simulated amplifier with a 1000 pF capacitive load is performed in 3.3 MHz gain bandwidth product, and phase margin of 50. The compensation capacitor is reduced extremely compared to conventional nested miller compensation methods. Since transconductance of each stage is not distinct, and it is close to one another; as a result, this method is suitable low power design methodology.     

Special all-round fillet weld for anchor rods of base-plate T-stub connections

The eccentricity between connected steel parts and the anchor rods in base-plate T-stub connections makes base plates the weaker components in tension and compression. Additionally, the oversized holes in base plates lead to irregular placement of anchor rods, resulting in an unsymmetrical shear behavior. Thus, this paper aims to develop a special all-round fillet weld to connect the anchor rods beneath the base plate concentrically to the steel part, removing the base plate from the load-transferring chain. Accordingly, design criteria were first developed based on Eurocode's directional method considering all the potential failure modes. Next, results were validated by conducting experimental work. The digital image correlation technique (DIC) was also used to capture the strain distribution developed over the tested specimen till failure. Consequently, numerical analysis was carried out to investigate the fracture strength and the fracture angle and compare the special fillet weld with its equivalent standard one, which has the same weld volume. The results indicated that the proposed design criteria produced safe strength prediction for the developed special all-round fillet weld. Furthermore, the results revealed that using a special all-round fillet weld instead of the equivalent standard one can increase the strength by about 8% and improve the ductility of the weld. However, it decreases the stiffness of the weld by about 21%. The fracture surface occurred at $15°$ from the face of the anchor rod, which produced a higher strength than the predicted tensile strength calculated according to the theoretical throat plane.     

Investigating shrinkage and moisture diffusivity of melon seed in a microwave assisted thin layer fluidized bed dryer

This work aimed to investigate the drying behavior of melon seed during combined fluidized bed-microwave drying system. Three drying air temperatures (40, 55 and 70 °C), three microwave powers (270, 450 and 630 W) and three air velocities (0.8, 1.5 and 2.3 m/s) were tested. Five mathematical models were selected to fit the experimental data for drying kinetics, and the results revealed that the Aghbashloo et al. model exhibited, in all cases, the best performance in fitting the experimental data (R² varying from 0.99088 to 0.99998; χ² from 0.00000 to 0.00185 and RMSE from 0.02289 to 0.82316). Calculated values of moisture diffusivity for dried melon seed varied from a minimum of 6.51 × 10?10 to a maximum of 6.59 × 10?9 m²/s under the tested drying conditions. Moisture diffusivity values increased as air temperature and microwave power was increased. Shrinkage values were calculated and found to vary in the range from 46.99 to 15.09 %.     

Integrated all-optical infrared switchable plasmonic quantum cascade laser

We report a type of infrared switchable plasmonic quantum cascade laser, in which far field light in the midwave infrared (MWIR, 6.1 μm) is modulated by a near field interaction of light in the telecommunications wavelength (1.55 μm). To achieve this all-optical switch, we used cross-polarized bowtie antennas and a centrally located germanium nanoslab. The bowtie antenna squeezes the short wavelength light into the gap region, where the germanium is placed. The perturbation of refractive index of the germanium due to the free carrier absorption produced by short wavelength light changes the optical response of the antenna and the entire laser intensity at 6.1 μm significantly. This device shows a viable method to modulate the far field of a laser through a near field interaction.