Synthesis and intercalation of silver nanoparticles in kaolinite/DMSO complexes

Ag nanoparticles were synthesized in the interlamellar space of a layered kaolinite. Disaggregation of the lamellae of the nonswelling kaolinite was achieved by the intercalation of dimethyl sulfoxide (DMSO). The kaolinite was suspended in aqueous AgNO₃ solution and the adsorbed Ag⁺ ions were reduced on the surface of kaolinite lamellae with NaBH₄ or UV light irradiation. The silver nanoparticles formed were characterized by X-ray diffraction (XRD), small angle X-ray scattering (SAXS), and transmission electron microscopy (TEM). We studied the effects of the two reduction methods on the size and the size distribution of Ag nanoparticles and how clay mineral structure is altered as a consequence of particle formation. It was established that the size of Ag nanoparticles depends on both silver content and the reduction method. Photoreduction of silver led to the formation of relatively large Ag nanoparticles (diameter 8–14 nm).     

Global Approach of Tribomechanical Development of Hybrid Aluminium Matrix Syntactic Foams

Hybrid syntactic foams with AlSi12 aluminium matrix were produced by pressure infiltration. The volume ratio of iron to ceramic hollow sphere reinforcement (in the same size range) was varied, and hybrid syntactic foams were also produced with bimodal size ceramic reinforcement. Previously, a very detailed analysis of the mechanical properties of the composites was made with quasi-static compression tests, and their tribological properties were investigated by pin-on-disc method in dry and lubricated conditions. The present article establishes and clarifies the correlations between mechanical and tribological properties. The coefficient of friction, height loss of the specimens and specific wear showed good correlation with different mechanical parameters, e.g. density, structural stiffness and yield strength. The established trends and correlations between mechanical and tribological behaviour enable a better understanding of materials design and selection for further applications of mechanically loaded sliding machine parts.     

Effects of microelements on soil nematode assemblages seven years after contaminating an agricultural field

Long-term effects of Cd, Cr, Cu, Se and Zn were studied 7 years after artificially contaminating plots of an agricultural field on a calcareous chernozem soil. Effects of three to four different contamination levels (originally 10, 30, 90 and 270 mg kg⁻¹) were studied. Nematode density was significantly reduced by 90 and 270 mg kg⁻¹ Se as well as by 270 mg kg⁻¹ Cr, while 90 and 270 mg kg⁻¹ Se also reduced nematode generic richness. Maturity Index values (calculated for c-p 2–5 nematodes) consistently decreased with increasing Cr and Se concentration and to a lesser extent in Zn plots as well. Structure Index showed decreasing trends in increasing Cr, Se and (to a lesser extent) in Zn treatments, while in Cd it shows a moderate increase. Distribution of c-p groups was negatively affected by the increasing Cr and Se concentration, while in Zn plots, this decrease was not significant. Response of feeding groups to pollutions was similar to other parameters: Cr and Se caused significant changes toward the loss of variability. The proportion of the most sensitive omnivorous and predatory nematodes decreased clearly as a consequence of Cr and Se treatments. Zn pollution also resulted in a slight decrease in this group, while Cd caused an increase. Nematode diversity profiles showed a significant decrease in the plots of increased Cr and Se concentrations, while increased concentrations of Cu and Zn resulted in ambiguous effects. Besides providing evidence on the harmful effects of Cr and Se on a soil nematode assemblage, our results suggest that simultaneous analysis of Maturity Index, Structure Index and diversity profiles provide a promising tool in nematological indication of soil pollution.     

Polyamine Metabolism under Different Light Regimes in Wheat

Although the relationship between polyamines and photosynthesis has been investigated at several levels, the main aim of this experiment was to test light-intensity-dependent influence of polyamine metabolism with or without exogenous polyamines. First, the effect of the duration of the daily illumination, then the effects of different light intensities (50, 250, and 500 μmol m^–2 s^–1) on the polyamine metabolism at metabolite and gene expression levels were investigated. In the second experiment, polyamine treatments, namely putrescine, spermidine and spermine, were also applied. The different light quantities induced different changes in the polyamine metabolism. In the leaves, light distinctly induced the putrescine level and reduced the 1,3-diaminopropane content. Leaves and roots responded differently to the polyamine treatments. Polyamines improved photosynthesis under lower light conditions. Exogenous polyamine treatments influenced the polyamine metabolism differently under individual light regimes. The fine-tuning of the synthesis, back-conversion and terminal catabolism could be responsible for the observed different polyamine metabolism-modulating strategies, leading to successful adaptation to different light conditions.     

Evaporation of water from particles in the aerodynamic lens inlet: an experimental study

The extremely high particle transmission efficiency of aerodynamic lens inlets resulted in their wide use in aerosol mass spectrometers. One of the consequences of transporting particles from high ambient pressure into the vacuum is that it is accompanied by a rapid drop in relative humidity (RH). Since many atmospheric particles exist in the form of hygroscopic water droplets, a drop in RH may result in a significant loss of water and even a change in phase. How much water is lost in these inlets is presently unknown. Since water loss can affect particle size, transmission efficiency, ionization probability, and mass spectrum, it is imperative to provide definitive experimental data that can serve to guide the field to a reasonable and uniform sampling approach. In this study, we present the results of a number of highly resolved measurements, conducted under well-defined conditions, of water evaporation from a range of particles, during their transport through an aerodynamic lens inlet. We conclude that the only sure way to avoid ambiguities during measurements of aerodynamic diameter in instruments that utilize low-pressure aerodynamic lens inlets is to dry the particles prior to sampling.     

Qualitative assessment of microstructure and Hertzian indentation failure in biocompatible glass ionomer cements

Discs of biocompatible glass ionomer cements were prepared for Hertzian indentation and subsequent fracture analyses. Specifically, 2 × 10 mm samples for reproducing bottom-initiated radial fracture, complemented by 0.2 × 1 mm samples for optimal resolution with X-ray micro tomography (μCT), maintaining dimensional ratio. The latter allowed for accurate determination of volumetric-porosity of the fully cured material, fracture-branching through three Cartesian axes and incomplete bottom-initiated cracking. Nanocomputed tomography analyses supported the reliability of the μCT results. Complementary 2-dimensional fractographic investigation was carried out by optical and scanning electron microscopies on the larger samples, identifying fracture characteristics. The combined 3-D qualitative assessment of microstructure and fractures, complemented by 2-D methods, provided an increased understanding of the mechanism of mechanical failure in these cements. Specifically, cracks grew to link pores while propagating along glass-matrix interfaces. The methodological development herein is exploitable on related biomaterials and represents a new tool for the rational characterisation, optimisation and design of novel materials for clinical service.     

Estimation of the Thermodynamic Limit of Overheating for Bulk Water from Interfacial Properties

The limit of overheating or expanding is an important property of liquids, which is relevant for the design and safety assessment of processes involving pressurized liquids. In this work, the thermodynamic stability limit—the so-called spinodal—of water is calculated by molecular dynamics computer simulation, using the molecular potential model of Baranyai and Kiss. The spinodal pressure is obtained from the maximal tangential pressure within a liquid–vapor interface layer. The results are compared to predictions of various equations of state. Based on these comparisons, a set of equations of state is identified which gives reliable results in the metastable (overheated or expanded) liquid region of water down to $-55$  MPa.     

Stability test of novel combined formulated dry powder inhalation system containing antibiotic: physical characterization and in vitro–in silico lung deposition results

Objective: The aim was to study the stability of dry powder inhaler (DPI) formulations containing antibiotic with different preparation ways – carrier-based, carrier-free, and novel combined formulation – and thereby to compare their physicochemical and in vitro–in silico aerodynamical properties before and after storage. Presenting a novel combined technology in the field of DPI formulation including the carrier-based and carrier-free methods, it is the most important reason to introduce this stable formulation for the further development of DPIs.

Methods: The structure, the residual solvent content, the interparticle interactions, the particle size distribution and the morphology of the samples were studied. The aerodynamic values were determined based on the cascade impactor in vitro lung model. We tested the in silico behavior of the novel combined formulated samples before and during storage.

Results: The physical measurements showed that the novel combined formulated sample was the most favorable. It was found that thanks to the formulation technique and the use of magnesium stearate (MgSt) has a beneficial effect on the stability compared with the carrier-based formulation without MgSt and carrier-free formulations. The results of in vitro and in silico lung models were consistent with the physical results, so the highest deposition was found for the novel combined formulated sample during the storage.

Conclusions: It can be established that after the storage a novel combined formulated DPI contained amorphous drug to have around 2.5?μm mass median aerodynamic diameter and nearly 50% fine particle fraction predicted high lung deposition in silico also.     

Morphology and adsorption properties of chemically modified MWCNT probed by nitrogen,n-propane and water vapor

The poor compatibility of carbon materials with different dispersion media can be overcome by surface functionalization. In this work, multiwall carbon nanotubes (MWCNTs) were doped by oxygen and nitrogen at low concentrations. Morphological and structural changes caused by chemical treatment were monitored using nitrogen, propane and water vapor adsorption measurements. Pore size distribution (PSD) functions derived from various models are compared. The contribution of slit-shaped pores to the total surface area available for adsorbed molecules is smaller than that of cylindrical pores. Functionalities with heteroatoms (both O and N) enhance water adsorption onto MWCNTs. However, no statistical difference is observed between the water adsorption properties of O- or N-containing MWCNTs.