The multiphase effect on crystal structure, hydrogen absorbing properties and electrode performance of Sc---Zr based Laves phase alloys

The crystal structure, hydrogen absorbing properties and electrode performance of Laves phase alloy systems, Sc---Zr---Ni---Mn and Sc---Ni---V systems, were studied by optical and scanning electron microscopy, X-ray powder diffraction, pressure-composition isotherm and electrochemical measurements. C14 and C15 Laves phases and minor ScNi-related phase were found in the Sc---Zr---Ni---Mn alloy system. The ScNi-related phase was composed of Sc, Zr and Ni elements. Two kinds of minor phase, BCC and ScNi-related phases, were identified in addition to the C15 phase in the Sc---Zr---Ni---V alloy system. The BCC contained mainly the element V. The ScNi-related phase contributed to an increase in the hydrogen capacity, but those in the V alloy system did not. The multiphase anode with a large amount of the ScNi-related phase showed a low durability against the KOH electrolyte. The substitution of Zr by Sc led to an improvement in the initial activation of the anode, but there was not a clear correlation between the presence of the multiphase in the anode and the rate capability.     

High-power hybrid plasma spraying of large yttria-stabilized zirconia powder

To testify to the advantage of large ceramic powder spraying, numerical simulations and experimental studies on the behavior of large yttria-stabilized zirconia (YSZ) powder in a high-power hybrid plasma spraying process have been carried out. Numeric predictions and experimental results showed that, with the high radio frequency (RF) input power of 100 kW, the most refractory YSZ powder with particle sizes as large as 88 μm could be fully melted and well-flattened splats could be formed. A large degree of flattening (ξ) of 4.7 has been achieved. The improved adhesive strength between the large splat and the substrate was confirmed based on the measurement of the crack density inside of the splats. A thick YSZ coating >300 μm was successfully deposited on a large CoNiCrAlY-coated Inconel substrate (50×50×4 mm in size). The ultradense microstructure without clear boundaries between the splats and the clean and crack-free interface between the top-coat and the bond-coat also indicate the good adhesion. These results showed that highpower hybrid plasma spraying of large ceramic powder is a very promising process for deposition of highquality coatings, especially in the application of thermal barrier coatings (TBCs).     

Emergency response to the nuclear accident at the Fukushima Daiichi Nuclear Power Plants using mobile rescue robots

On March 11, 2011, a massive earthquake (magnitude 9.0) and accompanying tsunami hit the Tohoku region of eastern Japan. Since then, the Fukushima Daiichi Nuclear Power Plants have been facing a crisis due to the loss of all power that resulted from the meltdown accidents. Three buildings housing nuclear reactors were seriously damaged from hydrogen explosions, and, in one building, the nuclear reactions became out of control. It was too dangerous for humans to enter the buildings to inspect the damage because radioactive materials were also being released. In response to this crisis, it was decided that mobile rescue robots would be used to carry out surveillance missions. The mobile rescue robots needed could not be delivered to the Tokyo Electric Power Company (TEPCO) until various technical issues were resolved. Those issues involved hardware reliability, communication functions, and the ability of the robots' electronic components to withstand radiation. Additional sensors and functionality that would enable the robots to respond effectively to the crisis were also needed. Available robots were therefore retrofitted for the disaster reponse missions. First, the radiation tolerance of the electronic componenets was checked by means of gamma ray irradiation tests, which were conducted using the facilities of the Japan Atomic Energy Agency (JAEA). The commercial electronic devices used in the original robot systems operated long enough (more than 100 h at a 10% safety margin) in the assumed environment (100 mGy/h). Next, the usability of wireless communication in the target environment was assessed. Such tests were not possible in the target environment itself, so they were performed at the Hamaoka Daiichi Nuclear Power Plants, which are similar to the target environment. As previously predicted, the test results indicated that robust wireless communication would not be possible in the reactor buildings. It was therefore determined that a wired communication device would need to be installed. After TEPCO's official urgent mission proposal was received, the team mounted additional devices to facilitate the installation of a water gauge in the basement of the reactor buildings to determine flooding levels. While these preparations were taking place, prospective robot operators from TEPCO trained in a laboratory environment. Finally, one of the robots was delivered to the Fukushima Daiichi Nuclear Power Plants on June 20, 2011, where it performed a number of important missions inside the buildings. In this paper, the requirements for the exploration mission in the Fukushima Daiichi Nuclear Power Plants are presented, the implementation is discussed, and the results of the mission are reported.     

A full‐color eyewear display using planar waveguides with reflection volume holograms

Abstract— A full‐color eyewear display with over 85% see‐through transmittance with a 16° horizontal field of view was developed. Very low color crosstalk, less than 0.008 Δu′v′ uniformity, and 120% NTSC color gamut were achieved. Waveguides with two in‐ and out‐coupling reflection volume hologram elements enabled a simple configuration that has an optical engine beside the user's temples. The reflection volume hologram elements used on the waveguides realized a small thickness of 1.4 mm for each waveguide, and an out‐coupling reflection volume hologram used as an optical combiner contributed a high see‐through transmittance of 85% due to its wavelength selectivity. However, there are technical challenges in achieving a reasonable screen size and quality color images with optics that utilize holographic waveguides because holograms have large chromatic dispersions compared to conventional optical elements such as lenses and mirrors. Approaches to overcome these issues are described.     

Lyapunov-based feedback design and experimental verification of IC engine speed control

In this paper, the speed control problem of internal combustion engines is investigated based on mean-value engine models. The dynamics of internal combustion engines is a complicated nonlinear system, and usually, it is difficult to know the exact values of the physical parameters. First, a Lyapunov-based design method is shown without requiring the full information of the physical parameters. Then, to improve transient performance, the design method is extended to several cases under different operation conditions. Numerical simulation results are presented for comparing the proposed design methods. Finally, experiments are conducted on an engine test bench and the results demonstrate the validity of the proposed design methods. Recommended by Editorial Board member Myotaeg Lim under the direction of Editor Hyun Seok Yang. The authors are grateful to Kai Zheng for his assistance of the model identification experiments. Jiangyan Zhang received the B.E. and M.E. degrees in Electrical Engineering, Yanshan University, China, in 2005 and 2008, respectively. Now, she is a Ph.D. candidate with the Department of Engineering and Applied Sciences, Sophia University, Tokyo, Japan. Her current research interests include nonlinear system control theory and applications to powertrain system control. Tielong Shen received the Ph.D. degree in Mechanical Engineering from Sophia University, Tokyo, Japan, March, 1992. From April 1992, he has been a faculty member of the Chair of Control Engineering in Department of Mechanical Engineering, Sophia University, where he currently serves as professor of the Department of Engineering and Applied Science. His research interests include control theory and application in mechanical systems, power systems, and automotive powertrain. Currently, he is an Associate Editor for the IEEE Control System Society Conference Editorial Board, and is serving as Associate Editor of Journal of Control Theory and Applications, and the Regional Editor Asia-Pacific for International Journal of Modeling, Identification and Control etc. Junichi Kako received the B.E. degree from Nagoya Institute of Technology, Nagoya, Japan. He joined Toyota Motor Corporation, Tokyo, Japan in 1989. He worked on various aspects of automotive powertrain control. From 1989 to 1994, he took part in the team for the development of Laboratory Automation (LA) system, Engineering Office Automation (EOD) system, and embedded system of powertrain control. During 1995–2001, he focused on the engine control systems in Powertrain Management Engineering Division. In 2002, he was with Future Project Division in which he was responsible for the R&D of model-based engine control system. Currently, he is developing engine control systems in the Powertrain Management Engineering Division, Toyota Motor Corporation. Shozo Yoshida received the M.S. degree in Engineering from Kyoto University, Kyoto, Japan. He joined Toyota Motor Corporation, Tokyo, Japan in 2000. From 2000 to 2004, he was with Future Project Division and worked on physical combustion modeling for Model-based Control Development. Since 2005, he has been with the Powertrain Management Engineering Division Toyota Motor Corporation, and is a member of the R&D of Model-based Engine Calibration.     

Methanation of carbon deposited directly from CO2 on rhodium-bearing activated magnetite

Methanation reactivity was studied for the surface carbon deposited from CO₂ on the surface of Rh-bearing activated magnetite. The most active material (Rh=0.83 wt %) for methanation was prepared by the impregnation method at 60°C and showed 98% conversion at 300°C. The surface carbon was composed of elemental carbon (-carbon) and polymerized carbon (-carbon), the proportion being dependent on the density of carbon deposited. In temperature-programmed surface reaction, the extent of conversion of the - and -carbon to CH₄ was 0.34 (-carbon) and 0.53 (-carbon), respectively, and the total conversion was 0.87. This result indicates that not only elemental carbon but polymerized carbon (-carbon) could be converted to CH₄ on the Rh-bearing activated (-carbon) magnetite, whereas -carbon is not hydrogenated on activated magnetite.     

Effect of end group of amorphous perfluoro-polymer electrets on electron trapping

Charge trap in amorphous perfluoro-polymer electret is studied, focusing on electron trap site and trap energy. Low-energy inverse photoelectron spectroscopy is adopted to measure solid-state electron affinity (EA) of cyclic transparent optical polymer (CYTOP). EA of CYTOP CTL-S is discovered by compensating the unwanted charge-up effect. Negatively-charged electret materials (polyethylene, ethylene-tetra-fluoro-ethylene, poly-tetra-fluoro-ethylene, and CYTOP) are analyzed by quantum mechanical calculation. Density functional theory with long-range correction is adopted to analyze orbital energies of single molecular systems. Intramolecular distribution of trapped electron and EA are investigated. Calculated electron affinities of CYTOP polymers with different end group are qualitatively in accordance with trapped charge stability measured with thermal stimulated discharge, signifying that electron affinities obtained with the present simulation can be used as an index of amorphous polymer electret.