Longitudinal diffusion and resistance to mass transfer as causes of nonideality in chromatography : J. J. van Deemter, F. J. Zuiderweg and A. Klinkenberg, Chem. Engng Sci. 5 271–289, 1956

The sharpness of separation in a gas-liquid chromatographic column is effected by longitudinal molecular diffusion, slowness to reach absorption equilibrium, and by flow irregularities in channels and across the column. The total effect of all these causes can be described by a simple equation which can be derived from the rigorous mathematical solution by introducing reasonable simplifying assumptions.     

Polymer networks based on α,ω-methacrylate-terminated poly(1,3-dioxolane)

α,ω-Methacrylate-terminated poly(1,3-dioxolane)s (polyDXL) were synthesized by cationic ring-opening polymerization of DXL in the presence of methylene-bis(oxyethylmethacrylate) as transfer agent. If the initiator concentration is small compared with the transfer agent concentration, the molecular weights of the polymers are governed by the ratio of the reacted monomer to the reacted transfer agent. The α,ω-methacrylate-terminated polyDXLs obtained undergo free radical polymerization with formation of polyacetal networks. The properties of the networks as function of the molecular weight of the corresponding prepolymers are reported.     

Recombination-induced variants of Clostridium acetobutylicum ATCC 824 with increased solvent production

Three sporulation-specific genes (orfA, sigE, sigG) from clostridium acetobutylicum ATCC 824 are arranged in a cluster, encoding the putative sigma E-processing enzyme, sigma E, and sigma sigma G respectively. When they were transformed into Clostridium acetobutylicum while on a plasmid functional in this organism, transformants did not survive. Three kinds of recombinations were then attempted with nonreplicative plasmids: duplication of orfA and sigE, replacement of all of the three genes, and inactivation of orfA. While the wild-type strain ceased to grow and produce solvents in batch cultures after approximately 24 h, mutant strains were isolated that showed sustained growth for a much longer time and produced a threefold increase in acetone and butanol in test tube cultures. In addition, one of the derived strains showed a significantly higher growth rate. Features of the restriction maps of the recombinants did not correlate with expected maps, indicating possible complications occurring during the recombination events.     

Sequence capture-PCR improves detection of mycobacterial DNA in clinical specimens

The rapid identification of mycobacterial DNA in clinical samples by PCR can be useful in the diagnosis of tuberculous infections, but several large studies have found that the sensitivity of this approach is not better than that of culture. In order to improve the sensitivity of detection of mycobacterial DNA in clinical specimens from patients with paucibacillary forms of tuberculosis, we have developed a procedure permitting the specific capture of mycobacterial DNA in crude samples prior to amplification, thereby concentrating the target sequences and removing irrelevant DNA and other potential inhibitors of the amplification reaction (sequence capture-PCR). By using this approach to capture and amplify two different sequences specific for organisms of the Mycobacterium tuberculosis complex (IS6110 and the direct repeat region), it was possible to detect as little as one genome of mycobacterial DNA in samples containing up to 750 micrograms of total DNA, representing a 10- to 100-fold increase in sensitivity compared with that obtained by purifying total DNA prior to amplification. Detection of the IS6110 sequence in pleural fluid samples from patients with tuberculous pleurisy by sequence capture-PCR gave positive results in 13 of 17 cases, including 3 of 3 culture-positive samples and 10 of 14 culture-negative samples. In contrast, when total DNA was purified from these samples by adsorption to a silica matrix prior to amplification, only the three culture-positive samples were positive by PCR. The sensitivity of detection of the direct repeat sequence in these samples by sequence capture-PCR was similar to that of IS6110 and, in addition, permitted immediate typing of the strains from some patients. We conclude that sequence capture-PCR improves the sensitivity of detection of mycobacterial DNA in paucibacillary samples. This approach should be useful in detecting rare target sequences from organisms implicated in other pathologic processes.     

Synthesis and thermal properties of polyamide 6 (A)-polyimide (B) block copolymers of ABA type

Summary Polyimides (PI) having different molecular weights were prepared by condensation of oxydiphthalic anhydride with 9,9-bis-(4-aminophenyl)fluorene in nitrobenzene solution at 180°C. These polyimides carried two amino chain ends which allowed us to fix polycaprolactam chains (PA6) to obtain PA6-PI-PA6 type copolymers. The elemental analysis and infrared spectroscopic determination gave the proportion of PA6 (or PI) in the copolymers. The studies of thermal properties-DSC and TGA-allowed us to characterize the copolymers.     

Monitoring systems and determination of actual fatigue usage

At GKN, fatigue monitoring of important components has been conducted since 1979. The monitoring methods depend on the mechanisms of damage; quasi-static loads are regarded as well as dynamic loads. The components were selected for monitoring on the basis of a system analysis. The data resulting from monitoring are used to optimise operation mode steadily. Experience shows that the use of monitoring data as input for fatigue assessment is the most realistic and cost-effective way. This fatigue assessment uses global and local sensitivity studies to evaluate the load-stress relation for each component. These relations can be programmed to produce stress vs. time curves. These are processed according to ASME rules to give a realistic fatigue usage.     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

Influence of interfacial microcracks on the elastic properties of composites

A model is established to quantify the influence of interfacial microcracks on the elastic properties of a particulate composite using a combination of theoretical and finite element analysis. A unique way to construct physical models which could accommodate both crack size and crack density is proposed. Based on energy principles, the influence of a dilute concentration of interfacial microcracks is first studied. The case of a finite concentration of microcracks is solved subsequently by combining the dilute concentration solutions and the differential scheme. Both cases agreed well with existing composite theories for the limiting condition of complete decohesion. The final model predicts the effective elastic properties as functions of both crack size and microcrack density.     

Diffusion bonding of ferritic oxide dispersion strengthened alloys to austenitic superalloys

The superior high temperature mechanical strength and oxidation resistance of ferritic oxide dispersion strengthened (ODS) tubular alloys are compromised by the difficulties encountered in joining. Conventional fusion welding techniques generate a weld fusion zone which is devoid of the mechanical strength exhibited by the base material. Therefore, more sophisticated solid state joining techniques, such as diffusion bonding, must be employed when joining ODS materials. This paper describes a series of solid state diffusion bonding experiments carried out between two tubular ferritic ODS alloys and two high temperature austenitic alloys. Careful control of bonding conditions produced pressure retaining joints between one of the tubular ODS alloys and both austenitic alloys. The successful joint design was incorporated into the manufacture of a tubular creep component, which enabled a series of internally pressurized creep tests to be carried out. The microstructure developed at the bond interface of each of the four separate material couples is described and the high temperature performance of the pressure retaining joints is discussed.     

Behavior of a vibrating wire near the liquid3He-vacuum interface and in a saturated3He-4He mixture

In this paper we describe the effect of the vicinity of a liquid³He-vacuum interface on the behavior of a vibrating wire viscometer. It was found that in the fluid near the liquid interface the quality factor is lower than in the bulk liquid. We further report on the observation of a doubling of the resonance peak of the wire in a saturated³He-⁴He mixture. The frequencies and amplitudes of the two peaks strongly depend on the distance between the phase boundary and the vibrating wire; the temperature and the velocity of the phase boundary have no significant influence on the peak frequencies. The observed peak doubling is attributed to the coupling of the vibrating wire with a standing second-sound wave in the dilute phase where the volume of the dilute phase can be regarded as a resonating cavity for second sound.