Dielectric and thermal characteristics of gel grown single crystals of ytterbium tartrate trihydrate

Dielectric and thermal characteristics of gel grown single crystals of ytterbium tartrate trihydrate have been carried out. The dielectric constant has been measured as a function of frequency in the range 2 kHz–1 MHz and temperature range 30–300 °C. The dielectric constant increases with temperature, attains a peak near 215 °C, and then decreases as the temperature exceeds 215 °C. The dielectric anomaly at 215 °C is suggested to be due to phase transition brought about in the material. The dielectric behaviour of the material is correlated with the results on thermal analysis. Thermogravimetric and differential thermal analysis have been used to study the thermal characteristics of the material. The experimental results show that the material is thermally stable up to 200 °C. The decomposition process occurs in two stages until ytterbium oxide is formed at 700 °C. The non-isothermal kinetic parameters e.g., activation energy and the frequency factor have been evaluated for each stage of thermal decomposition by using the integral method, applying the Coats–Redfern approximation.     

Hydrogen adsorption studies in micro-size cobalt dots

Hydrogen desorption curves were obtained from a sample composed of a square arrangement of Co dots with average diameter of 4.4 μm, separated by a distance of 11.6 μm. A macroscopic sample of Co dots grown on a 2.5 × 2.5 cm Si substrate was made by standard lithographic techniques and used in these experiments. Thermal programmed desorption (TPD) was performed under ultra-high vacuum conditions. Hydrogen TPD curves were obtained from a 1 × 1 cm Co dots samples displaying a maximum of intensity at 425 K. Hydrogen TPD curve was also obtained from 1 cm× 1 cm samples of Co films and Co foils for comparison. The hydrogen TPD curves have decreasing intensity from the Co foils to the Co dots and finally to the Co films. This indicates that there are more sites for hydrogen adsorption on the Co dots than in the Co films. This is a surprising result because there is approximately 8.7 times less Co atoms exposed in the Co dots that in the Co film sample. A desorption energy of 27 kcal/mol was obtained for the Co dots suggesting that hydrogen is adsorbed on an hcp hollow site of the Co dot crystalline structure.     

A review on the synthesis of in situ aluminum based composites by thermal,mechanical and mechanical–thermal activation of chemical reactions

The aim of the present paper is to review the recent progress in the synthesis of in situ particle reinforced aluminum composites using thermal, mechanical and combined mechanical-thermal activation of aluminothermic reduction reactions. The combination of combustion synthesis (CS) and mechanosynthesis (MS) is the most recent development in the processing of advanced materials like micro and nano aluminum based composites. The combined mechanical thermal synthesis (MTS) has widened the possibilities for both CS and MS. MTS holds great potential for commercial viability and offers exciting processing route for the synthesis of advanced materials. Enhanced reaction kinetics and extended concentration limits in MTS are demonstrated by illustrating the synthesis of aluminum based nanocomposite involving Al–CeO₂.     

Dissolution processes,hydrolysis and condensation reactions during geopolymer synthesis: Part I—Low Si/Al ratio systems

Initial geopolymeric reaction processes governing dissolution of solid aluminosilicate particles in alkali solutions have been investigated using conventional experimental techniques, and the data analysed by speciation predictions of the partial charge model (PCM). For metakaolin powders activated with 5.0 M NaOH, solid-state nuclear magnetic resonance (NMR) spectra disclose the existence of monomeric [Al(OH)₄]⁻ species after two hours of dissolution, consistent with PCM predictions. However, no equivalent monomeric silicate species were observed for 5.0–10.0 M NaOH activator solutions characteristic of systems with nominal Si/Al ≤ 1. The apparent absence of monomeric silicate species suggest rapid condensation of silicate units with [Al(OH)₄]⁻ to generate aluminosilicate species, as indicated by the evolution of the shoulder at around −87 ppm in the ²⁹Si NMR spectra. Of the two possible stable silicate species [SiO₂(OH)₂]²⁻ and [SiO(OH)₃]⁻, the latter appears most likely to condense with [Al(OH)₄]⁻ to produce aluminosilicate oligomers, from which larger oligomers subsequently form through further condensation with [Al(OH)₄]⁻ leading to a gradual build up of aluminosilicate networks and a lowering of system alkalinity. This dissolution and hydrolysis sequence at the early stages of synthesis suggests a reaction path wholly consistent with predictions of the partial charge model.     

Temperature waves in a horizontal liquid layer cooled from above

Waves in a thermal boundary layer were obtained by numerically modeling the natural thermogravitational convection in the infinite horizontal layer of a liquid cooled from above. The waves are generated via a mechanism related to the loss of stability and periodic separation of the upper, heavier and cooler liquid layer (penetrative convection).     

Surface barrier diode based on zinc selenide with a passivating zinc oxide film

We propose a method of fabricating surface barrier diodes with overlapped metal junction, which provides for a significant decrease in the reverse currents and an increase in the breakdown voltage.     

An analysis of nonlinear ion drift spectrometry for gas detectors with separating chamber of planar geometry

A consistent analytical model of nonlinear ion drift spectrometry for modern gas analyzers is developed. A procedure for determining the field dependence of the ion mobility using the experimental data is described. An ionogram is calculated for the case of a flat drift chamber and polynomial character of the field dependence of the ion mobility.