Magnetic field dependence of shielding current density in Y-Ba-Cu-O rings at 77 K

A method for contactless measurement of the shielding critical current density and its dependence on the external magnetic field is described and analyzed. The obtained values are compared with those measured resistively on two different samples. It is shown that the shielding critical current densityJ _cs and the intergranular transport current densityJ _cr are identical if the measurement conditions are similar. A degradation ofJ _cs measured in the external field with AC ripple has been observed.     

Analysis of a stiffener intersection eccentricity in a steel containment

Containment structures have several regions in which the continuity of the cylindrical pressure boundary is interrupted, e.g., shell penetrations, discontinuous stiffeners, and changes in the shell thickness. Significant strain concentrations can occur in these areas of discontinuity. The Sandia National Laboratories 1:8-scale steel containment equipment hatch was analyzed as an example of an eccentricity at a stiffener intersection.A portion of the as-built 1:8-scale model was modeled with the ANSYS general purpose finite element program using triangular, thin shell finite elements. The overall size of the model was determined from Saint-Venant type considerations of the stress field around the hatch. Shell elements were used to model the ring and formed stiffeners. Geometric and material nonlinear behavior were included. The model was loaded using discrete load steps up to a pressure of 165 psig. At this pressure, the maximum strain was 19.7 percent in the formed stiffener near its intersection with the ring stiffener. The finite element solution demonstrated the very localized nature of the strain field near the ring/formed stiffener intersection.In an attempt to reduce analysis costs, a small portion of the 1:8-scale model immediately surrounding the ring/formed stiffener intersection was selected for further analysis. Two smaller models, a ring/formed stiffener intersection and a ring/circular stiffener intersection, were studied. The models were significantly smaller than the regions used previously. A comparison of the two intersection models showed that the circular stiffener is a more efficient configuration.     

Thermal image analysis for polygraph testing

We have designed, developed, and tested a very promising thermal image analysis method for polygraph testing. The method achieved a correct classification rate of CCR= 84% on the test population to our avail. This method, once refined, can serve as an additional channel for increasing the reliability and accuracy of traditional polygraph examination. We extract subtle facial temperature fluctuation patterns through nonlinear heat transfer modeling. The modeling transforms raw thermal data to blood flow rate information. Then, we use the slope of the average periorbital blood flow rate as the feature of a binary classification scheme. The results come to support our previous laboratory findings about the importance of periorbital blood flow in anxious states.     

Power system analysis using space-vector transformation

In this paper, the space-vector transformation used in machine vector control is applied to power system analysis. The proposed method is used to model electric machines, power electronic converters, transformers, and transmission lines and to analyze power sources and loads with different connections (delta and wye). This method can also be applied to analyze steady-state (or transient phenomena) and unbalanced sources, including harmonics. Models obtained with this method are as simple as those of the per-phase approach. With the space-vector transformation, instantaneous active and reactive power concepts can be generalized, and new power system control strategies can be developed when power electronic converters are used. Steady-state, transient behavior, and harmonic analyses examples and applications are presented to illustrate the performance and advantages of the proposed method. This method can be extended to unbalanced systems (e.g., unsymmetric faults) using instantaneous symmetrical components in polyphase balanced circuits.     

IEEE Richard Harold Kaufmann Award Call for Nominations

This letter further discusses the difference between different definitions of voltage unbalance. Contrary to an earlier letter (see P. Pillay et al., ibid., vol.5, p.50-1, 2001), it is concluded that different definitions may give significantly different results. The two IEEE definitions that were not discussed in the earlier letter give different results and both deviate significantly from the true value (ratio of negative, and positive-sequence voltage) when a zero-sequence component is present.     

Primary hydration of poly(acrylic acid) sodium salts

Summary The equilibrium water contents of linear poly(acrylic acid) sodium salts with different degrees of neutralisation were found to be dependent on temperature and relative humidity. An octahedral model for the primary hydration of poly(acrylic acid) sodium salts (HIRAOKA and YOKOYAMA 1980) was critically evaluated in the light of these findings and an anomaly in the water uptake versus neutralisation curve at approximately 33% neutralisation was explained by the counterion condensation theory. (MANNING 1979).     

Intelligent identification and control for autonomous guided vehicles using adaptive fuzzy-based algorithms

Fuzzy logic was first suggested as the mechanism by which humans drive cars. This paper addresses the use of fuzzy logic and algorithms towards the intelligent autonomous motion control of land vehicles. To cope with vehicle complexities, internal parametric changes, and with unpredictable environmental effects, the controllers that are presented, whilst heuristic in nature, are self-organizing or self-learning in that they generate automatically by observation an experiential rule base that models the vehicle, and via an appropriate performance index an optimal control rule base that is robust to large parametric changes. The methodology presented is applicable to any complex process which is too difficult to model or control using conventional methods, or which has relied on the experience of a human operator. An overview of fuzzy logic and static fuzzy logic control (akin to expert systems) is provided, together with illustrative examples.     

Considerations in application and selection of unit substationtransformers

This paper discusses secondary unit substations transformers (USTs) ranging from 300 up through 2500 kVA with 34.5-kV maximum primary voltages and with secondary voltages 600 V and below. Pad-mounted (compartmentalized) transformers are not considered in this paper. The first part of this paper discusses USTs belonging to two general categories, liquid type and dry type (nonliquid type). Liquid types include a discussion of the presently available insulating fluids: mineral oil, high-temperature hydrocarbon fluid, silicone fluids, and the new vegetable-based fluids. Dry types include a discussion of vacuum pressure impregnated polyester, vacuum pressure encapsulated silicone, partial cast, and full cast insulation systems. The National Electric Code (1999) requirements as they affect both liquid- and dry-type USTs for both outdoor and indoor locations are considered. The paper discusses the relative advantages of each UST within each category with respect to the following: (1) first cost; (2) operating costs (losses); (3) overload capability; (4) fan cooling; (5) space factor; (6) environmental factors; (7) sound levels; and (8) maintenance     

Control of free-radical emulsion polymerization of methyl methacrylate by oxygen injection. II. Experimental study

Oxygen injection has been proposed and experimentally demonstrated as an effective control measure for limiting the rate of heat release and altering the rate of polymerization in emulsion processes. A detailed mathematical model has been previously developed to describe the system behavior with and without oxygen injection. A simple lab scale apparatus was constructed and run extensively. Only trace quantities of oxygen are needed to inhibit the reaction completely. The facile response makes this method attractive for fast temperature control. However, because of the rapid penetration of dissolved oxygen into the polymer particles, growing radical chains are terminated prematurely, lowering product molecular weights. To minimize this detrimental effect, pulsed oxygen control is used and extensive experimental work was performed to determine the effects of controller set points on molecular weight. Moderate oxygen flows and moderate set point temperatures are found to give the optimal response without significant lowering of the final molecular weight. Injected quantities agree well with the order-of-magnitude sparging calculations needed to completely stop initiation. However, complete agreement between model simulations and experimental results was not reached due to an unmeasured loss of monomer from the reactor. Chain transfer to monomer is found to be important in modeling the polymer molecular weight. It has, however, a negligible effect on the reaction rate.