Microwave Communication to Moving Parts Inside Machines

Cables to moving parts on a linear actuator in production machines, such as pick-and-place machines, are a source of unreliability owing to the possible breaking of a cable. They further reduce the positioning precision of the actuator owing to additional forces. Slotted waveguide systems for rail vehicles based on 2.4 GHz transmission frequency are well known, but transmitters/receivers and waveguides are bulky. The paper reports on the reduction in size of the equipment, adapted to 5.8 GHz using a commercial off-the-shelf RadioLan communication module. Further, the efficient termination of the wave-guide and a new way to reduce standing-wave effects is also discussed.     

Mechanical behavior of 30–50 nm thick aluminum films under uniaxial tension

We present uniaxial tensile test results for 30–50 nm thick freestanding aluminum films. Young’s modulus and ductility were found to decrease monotonically with grain size. Reverse Hall–Petch behavior was observed with no appreciable room temperature creep. Non-linear elasticity with small irreversible deformation was observed for 50 nm thick specimens.     

论城市可持续性发展与地下空间利用

本文分析了目前制约我国城市可持续发展的最主要因素是低效率的土地利用方式 ,若使地上、地面、地下空间协调发展 ,合理科学的规划好地下空间 ,珍惜地下空间资源 ,健全地下空间法律法规 ,统一地下空间管理机构 ,则可高效率的利用土地。     

The zinc-rich corner of the Zn-Fe-Ni-Si quaternary system at 450 °C

Following up on recent studies of the Zn-rich corners of the Zn-Fe-Ni and Zn-Fe-Si ternary systems, a 450 °C isothermal section of the Zn-Fe-Ni-Si quaternary phase diagram with the Zn composition being fixed at 93 at.% was determined experimentally using optical microscopy, scanning electron microscopy (SEM) coupled with energy dispersive x-ray spectroscopy (EDS), and x-ray diffractometry (XRD). FeSi was found to be in equilibrium with almost all phases in the section, including the T, ζ, Ni-δ, NiSi₂, and FeSi₂ phases, as well as the liquid phase (L). Silicon solubilities in the T, ζ, and Ni-δ phases were rather limited. However, the solubilities of Fe and Zn in the NiSi₂ phase, at 4.5 at.% and 7.2 at.%, respectively, were appreciable. The existence of the (L+NiSi₂+Ni-δ) three-phase equilibrium state apparently prevents other Ni-Si compounds from entering equilibrium with the liquid at 450 °C. No true quaternary compound was found in the study.     

DEPOSITIONAL AND DIAGENETIC HISTORY OF THE KERENDAN CARBONATE PLATFORM, OLIGOCENE, CENTRAL KALIMANTAN, INDONESIA

The Kerendan carbonate platform (Oligocene Berai Limestone) covers a subsurface area measuring approximately 11 by 16 km in the westernmost Kutei Basin, Central Kalimantan. Aggradation of the Kerendan platform occurred during a major Oligocene transgression, and is contemporaneous with aggradation and backstepping of the Barito shelf margin which was located approximately 30 km to the south. The Kerendan platform is approximately 1,000 m thick, and comprises three aggrading seismic sequences identified by the downlap of basinal strata at the platform margin and downlap of transgressive strata within the platform. Carbonate deposition started in the Late Eocene, and ended when the upper limestone sequence drowned and was covered with shale in the Late Oligocene (approximately 28.6 Ma). Three depositional areas can be distinguished in seismic sections: (1) a platform interior (lagoon); (2) a slightly raised platform rim (1–2 km wide); and (3) a basinward‐dipping platform margin and slope. The margin of the platform is identified by inflections on the seismic profiles where the relatively flat platform top begins to slope basinward. Depositional models from outcrops combined with core from three Kerendan wells were used to extrapolate depositional facies onto the seismically‐defined platform. Platform‐interior (lagoon) facies consist largely of fossiliferous wackestones and packstones, and porosities are generally lower than 5%. The platform rim is characterized by interbedded bioclastic wackestones, packstones, grainstones and boundstones, with grainstones increasing toward the platform margin. Porosity preferentially occurs in packstones, grainstones and boundstones. The platform‐rim deposits have greater porosity (5–13%) than the platform interior because the platform run is more grainstone‐rich, and because acidic waters compacting out of basinal shales concentrated dissolution near the platform margin. Pore types include vuggy porosity, microporosity within grains, and intercrystalline porosity in dolomite in the upper part of the platform rim. Different pore types have resulted in variable but locally very high permeabilities (greater than 100 mD). Permeabilities decrease with depth as vuggy pores decrease, and microporosity becomes dominant.     

利用反射纵波评价裂缝倾角的模拟实验研究

声波全波列测井中的反射纵波可以用来评价高角度裂缝和对井周附近地质结构进行成像。目前的研究主要侧重于直接从波形资料处理出发计算裂缝的位置和倾角 ,其可靠性和准确性无从评价和校验。文中采用模拟实验的方法记录了倾角为 6 0°～80°范围内的 8种倾角裂缝的反射脉冲纵波波形 ,自行推导了反演裂缝倾角的公式 ,结合波场分离技术对实验测量波形数据进行了处理 ,计算出的裂缝倾角与实际值具有良好的一致性。本文结果表明 ,利用至少 2个深度点的纵波反射波波形资料就可以准确地反演裂缝的倾角     

A systematic techno-economic assessment of a WEC system installation for low-cost electrification of a habitable dwelling

This paper deals with the technical feasibility and economic viability of a grid connected wind-energy conversion system (WECS) used to cover the energy demand of an average habitable dwelling. The various parts of the wind-energy system are described and the useful electrical energy production is determined using a simulation program based on the Monte Carlo method. An economic analysis of the WEC system is performed using a computerized assessment tool. Important financial indices are calculated and financial scenarios investigated.     

Metal-insulator-semiconductor solar cell under gamma irradiation

The performance of a home made MIS–p-Si solar cell was experimentally studied under various gamma irradiation doses (up to 500 Mrad). The effect of radiation dose on the I−V and C−V characteristics was investigated in this work. The obtained results showed that all the output parameters of the cells under investigation were degraded with gamma radiation exposure. In addition, the effects of fabrication conditions (metal thickness and adding of antireflection coating) on the cell output parameters were also investigated.