Multifactor Experiments under Superdeep-Penetration Conditions

Consideration is given to the possibility of controlling the efficiency of the process of superdeep penetration of a high-velocity microstriker flux into metal obstacles due to the employment of ballast elements in the jet and to additional supply of energy in compression by an explosive charge along the external perimeter.     

Failure analysis of aluminum cable steel reinforced (ACSR) conductor of the transmission line crossing the Paraná River

The failure of the conductor of the 460 kV overhead transmission line located along the crossing of the Paraná River was investigated. As a result of this failure, a blackout took place in the southern states of Brazil in January of 2002, reaching approximately 67 million inhabitants. Investigation of the external aluminium layer of the ACSR conductor near the fracture showed typical static deformation marks and dynamic fretting wear tangential marks, both associated with the presence of Al₂O₃ debris. Additionally, encrusted silicon particles were observed on the external surface of the strands. The internal Al layer showed elliptical deformation marks also associated with Al₂O₃ debris. Both Al₂O₃ and Si particles are efficient abrasive material, which associated with slight relative motion of metallic surfaces (clamp/strand and strand/strand) can promote fretting wear. Two types of fracture surface of the Al strands were identified: 45° and quasi-normal surfaces, the former being the predominant type. Delamination and particle detachment were the mechanisms of superficial degradation observed on the Al strands, indicating that the rupture of the strands occurred under a gross slip fretting regime induced by sub-conductor oscillation. Inspection of the internal surface of as-cast Al–10%Si spacer clamps revealed different stages of intense circumferential wear caused by the preferential cracking and particle detachment of the eutectic constituent of the as-cast microstructure. This intense wear reduces the clamping contact pressure, which allows higher displacement amplitude and leads to the critical fretting regime. Finally, a few suggestions are discussed to minimise the occurrence of future failures.     

Special features of the periodic-pulse-train laser radiation confinement in doped gallium arsenide and zinc selenide

Experimental data on the pulsed laser radiation confinement in compensated GaAs and ZnSe with deep impurity levels are reported for the laser wavelength λ=1.55 μm and a pulse repetition frequency of up to 100 kHz. It is demonstrated that an increase in the pulse repetition rate is accompanied by a decrease in the energy confinement threshold and by an increase in the radiation attenuation coefficient. These effects are explained by the accumulation of nonequilibrium charge carriers related to a dependence of the recombination time constant on the concentration of free impurity centers.     

Shallow Linear Action Graphs and their Embeddings

Action calculi, which generalise process calculi such as Petri nets, π-calculusand ambient calculus, have been presented in terms of action graphs. We here offer linear action graphs as a primitive basis for action calculi. This paper presents the category of embeddings of undirected linear action graphs without nesting, using a novel form of graphical reasoning which simplifies some otherwise complex manipulations in regular algebra. The results are adapted in a few lines to directed graphs. This work is part of a long-term search for a uniform behavioural theory for process calculi. Received October 2000 / Accepted in revised form April 2001     

High-voltage bridge for measuring spontaneous polarization,dielectric constants,and conductivity of ferroelectric crystals

Translated from Izmeritel'naya Tekhnika, No. 9, pp. 34–35, September, 1989.     

Magnetic field dependence of shielding current density in Y-Ba-Cu-O rings at 77 K

A method for contactless measurement of the shielding critical current density and its dependence on the external magnetic field is described and analyzed. The obtained values are compared with those measured resistively on two different samples. It is shown that the shielding critical current densityJ _cs and the intergranular transport current densityJ _cr are identical if the measurement conditions are similar. A degradation ofJ _cs measured in the external field with AC ripple has been observed.     

Analysis of a stiffener intersection eccentricity in a steel containment

Containment structures have several regions in which the continuity of the cylindrical pressure boundary is interrupted, e.g., shell penetrations, discontinuous stiffeners, and changes in the shell thickness. Significant strain concentrations can occur in these areas of discontinuity. The Sandia National Laboratories 1:8-scale steel containment equipment hatch was analyzed as an example of an eccentricity at a stiffener intersection.A portion of the as-built 1:8-scale model was modeled with the ANSYS general purpose finite element program using triangular, thin shell finite elements. The overall size of the model was determined from Saint-Venant type considerations of the stress field around the hatch. Shell elements were used to model the ring and formed stiffeners. Geometric and material nonlinear behavior were included. The model was loaded using discrete load steps up to a pressure of 165 psig. At this pressure, the maximum strain was 19.7 percent in the formed stiffener near its intersection with the ring stiffener. The finite element solution demonstrated the very localized nature of the strain field near the ring/formed stiffener intersection.In an attempt to reduce analysis costs, a small portion of the 1:8-scale model immediately surrounding the ring/formed stiffener intersection was selected for further analysis. Two smaller models, a ring/formed stiffener intersection and a ring/circular stiffener intersection, were studied. The models were significantly smaller than the regions used previously. A comparison of the two intersection models showed that the circular stiffener is a more efficient configuration.     

Effect of moderate to very low fat defined formula diets on serum lipids in healthy subjects

Serum total cholesterol, high density lipoprotein (HDL) cholesterol, and triglyceride levels were studied in healthy male and female subjects consuming for one-week periods a diet of conventional food (CF) providing 42% of energy as fat, principally butter fat, and then in random order nutritionally complete, defined formula diets of moderate (32%) to very low (1%) fat content. Compared to CF, the formula with 32% of energy as corn oil lowered serum cholesterol by 25% and the ratio of total to HDL-cholesterol by 13%. Low (9%) and very low (1–3%) fat formulas reduced HDL-cholesterol by as much as 40%, raised the total: HDL-cholesterol ratio by about 20% and raised serum triglyceride levels by as much as 100%. When low and very low fat formulas were ingested for three weeks, these effects persisted although maximal responses occurred during the first week. These results demonstrated that a moderate fat formula diet with a high P/S ratio had a more favorable effect on serum lipid levels than various low fat formulas. Low fat conventional food diets should be studied in long-term controlled metabolic experiments before such diets are recommended to the general population for coronary heart disease or cancer prevention.