Optimization Methods for Post-Bond Testing of 3D Stacked ICs

Testing of three-dimensional (3D) stacked ICs (SICs) is starting to receive considerable attention in the semiconductor industry. Since the die-stacking steps of thinning, alignment, and bonding can introduce defects, there may be a need to test multiple subsequent partial stacks during 3D assembly. We address the problem of test-architecture optimization for 3D stacked ICs to minimize overall test time when either the complete stack only, or the complete stack and multiple partial stacks, need to be tested. A general solution to this problem provides several options for 3D stack testing in a unified framework. We show that optimal test-architecture solutions and test schedules for multiple test insertions are different from their counterparts for a single final stack test. In addition, we present optimization techniques for the testing of TSVs and die-external logic in combination with the dies in the stack.     

UTRA/FDD RF Transceiver Requirements

Unified RF requirements are derived for an UMTS Terrestrial RadioAccess/Frequency Division Duplex (UTRA/FDD) compliant mobile transceiver. Aset of transceiver requirements are proposed with consideration to systemissues including duplex aspects. From these design-compatible requirements areproposed for each functional block in the transceiver.     

边缘接入智能化

MMAP(多功能、多业务接入平台)集成了光纤传输和接入技术,使接入网和城域网(MAN)融合在一起。     

改进缺陷,套刻和聚焦性能的第五世代浸没式曝光系统

论述了第五世代双扫描平台浸液式扫描曝光机的性能和进展。表明了在高速扫描状态下有生产价值的套刻和聚焦性能的实现。浸液式设备更多的关键部分与缺陷有关,而且该机的改进是通过有生产价值的缺陷水平方面来体现的。为了保持这种缺陷水平的改进效果,需要在圆片应用中进行专门稳定的测量。特加是边缘空泡除去(EBR)设计和圆片斜面良流线性是很重要的。     

Interdigitated back‐contact heterojunction solar cell concept for liquid phase crystallized thin‐film silicon on glass

We present an interdigitated back‐contact silicon heterojunction system designed for liquid‐phase crystallized thin‐film (~10 µm) silicon on glass. The preparation of the interdigitated emitter (a‐Si:H(p)) and absorber (a‐Si:H(n)) contact layers relies on the etch selectivity of doped amorphous silicon layers in alkaline solutions. The etch rates of a‐Si:H(n) and a‐Si:H(p) in 0.6% NaOH were determined and interdigitated back‐contact silicon heterojunction solar cells with two different metallizations, namely Al and ITO/Ag electrodes, were evaluated regarding electrical and optical properties. An additional random pyramid texture on the back side provides short‐circuit current density (j_SC) of up to 30.3 mA/cm² using the ITO/Ag metallization. The maximum efficiency of 10.5% is mainly limited by a low of fill factor of 57%. However, the high j_SC, as well as V_OC values of 633 mV and pseudo‐fill factors of 77%, underline the high potential of this approach. Copyright © 2015 John Wiley & Sons, Ltd.     

Spatiotemporal EEG/MEG source analysis based on a parametric noise covariance model

A method is described to incorporate the spatiotemporal noise covariance matrix into a spatiotemporal source analysis. The essential feature is that the estimation problem is split into two parts. First, a model is fitted to the observed noise covariance matrix. This model is a Kronecker product of a spatial and a temporal matrix. The spatial matrix models the spatial covariances by a function dependent on sensor distance. The temporal matrix models the temporal covariances as lag dependent. In the second part, sources are estimated given this noise model, which can be done very efficiently due to the Kronecker formulation. An application to real electroencephalogram (EEG) data shows that the noise model fits the data very well. Simulation results show that the resulting source estimates are more precise than those obtained from a standard analysis neglecting the noise covariance. In addition, the estimated standard errors of the source parameter estimates are far more precise than those obtained from a standard analysis. Finally, the source parameter standard errors are used to investigate the effects of temporal sampling. It is shown that increasing the sampling by a factor x, decreases the standard errors of all source parameters with the square root of x.     

A low-power 2/5.8-GHz dual-wide-band CMOS LC-VCO with switched-inductor technique

A fully integrated dual-band LC voltage control oscillator, designed in a 0.18-µm CMOS technology for 5.8-GHz/2.0-GHz wireless communication applications, is described. The frequency band switching is accomplished with switched-inductor technique. The dual-band oscillator can be operated in 5.38–6.23?GHz and 1.78–2.07?GHz with 15% frequency tuning range. Two different inductors are used for the frequency band switching. Frequency tuning is implemented by varying the capacitance of a MOS varactor. The measured phase noise is ?109?dBc/Hz @ 1?MHz and ?112?dBc/Hz @ 1?MHz for frequency at 5.8?GHz and 2?GHz, respectively. This oscillator is fabricated in UMC's 0.18-µm one-poly-six-metal 1.8?V process. The power dissipation of this dual-band VCO is 11.7 and 9.3?mW for oscillation frequency of 2?GHz and 5.8?GHz, respectively.     

Power and Speed-Efficient Code Transformation of Video Compression Algorithms for RISC Processors

Upcoming multi-media compression applications will require high memory bandwidth. In this paper, we estimate that a software reference implementation of an MPEG-4 video decoder typically requires 200 Mtransfers/s to memory to decode 1 CIF (352×288) Video Object Plane (VOP) at 30 frames/s. This imposes a high penalty in terms of power but also performance.However, we also show that we can heavily improve on the memory transfers, without sacrificing speed (even gaining about 10% on cache misses and cycles for a DEC Alpha), by aggressive code transformations. For this purpose, we have manually applied an extended version of our data transfer and storage exploration (DTSE) methodology, which was originally developed for custom hardware implementations.     

A subspace matching color filter design methodology for a multispectral imaging system.

In this paper, we present a methodology to design filters for an imaging system to improve the accuracy of the spectral measurements for families of reflective surfaces. We derive the necessary and sufficient conditions that the sensor space of the system must obey in order to measure the spectral reflectance of the surfaces accurately. Through simulations, we show how these conditions can be applied to design filters using a set of sample spectral data acquired from extracted teeth. For this set of data, we also compare our results to those of Wolski's method, a conventional filter design method which produces filters that recover tristimulus values of surfaces accurately under several illuminants. We show that our method produces filters that capture the spectral reflectance better given the same number of measurements. The errors in predicting the color of the sample data are much lower under every test illuminant when the filters designed with our method are used.