The effects of processing variables on stress development in ultraviolet-cured coatings

A cantilever deflection technique was used to monitor stress development during ultraviolet photo-cure of acrylate coatings to the glassy state. Two coating systems were studied: a trifunctional monomer (trimethylol propane triacrylate, TMPTA) and a tetrafunctional monomer (pentaerythritol tetraacrylate, PETA). Both were photoinitiated with 2,2-dimethoxy-2-phenylacetophenone (DMPA). Average in-plane stresses of up to 30 MPa were measured upon curing at room temperature. The rate and magnitude of stress development rose with the photoinitiator concentration and with light intensity. Curing with more strongly absorbed light had similar effects. Light absorption caused decreased stress magnitudes in thicker coatings. Somewhat unexpectedly, the rate and magnitude of stress development increased with monomer functionality even though the conversion fell. Moreover, curing thick coatings with high radical concentrations (strongly absorbing light and large photoinitiator concentrations) caused ripple defects to form. With the appearance of these defects, stress ceased to rise with the photoinitiator concentration. Fourier transform infrared spectroscopy was employed to monitor conversion and to help understand these stress development trends. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1267–1277, 1997     

Electrical conductivity modeling of carbon black/polycarbonate,carbon nanotube/polycarbonate,and exfoliated graphite nanoplatelet/polycarbonate composites

Adding conductive carbon fillers to electrically insulating thermoplastic polymers increases the resulting composite's electrical conductivity, which would enable them to be used in electrostatic dissipative and semiconductive applications. In this study, varying amounts of carbon black (CB: 2 to 10 wt %), multiwalled carbon nanotubes (CNT: 0.5 to 8 wt %), or exfoliated graphite nanoplatelets (GNP: 2 to 15 wt %) were added to polycarbonate (PC) and the resulting composites were tested for electrical conductivity (EC = 1/electrical resistivity). The percolation threshold was ～ 1.2 vol % CNT, ～ 2.4 vol % CB, and ～ 4.6 vol % GNP. In addition, three EC models (Mamunya, additive, and general effective media) were developed for the CB/PC, CNT/PC, and GNP/PC composites. The general effective media (GEM) model showed the best agreement with the experimental results over the entire range of filler concentrations (above and below the percolation threshold) for all three composite systems. In addition, the GEM model can be easily adapted for composites containing combinations of different conductive fillers. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Thermal properties of sodium borosilicate glasses as a function of sulfur content

Sulfur trioxide (SO₃) additions, up to 3.0 mass%, were systematically investigated for effects on the physical properties of sodium borosilicate glass melted in air, with a sulfur-free composition of 50SiO₂–10Al₂O₃–12B₂O₃–21Na₂O–7CaO (mass%). Solubility measurements, using electron microscopy chemical analysis, determined the maximum loading to be ~1.2 mass% SO₃. It was found that measured sulfur (here as sulfate) additions up to 1.18 mass% increased the glass transition temperature by 3%, thermal diffusivity by 11%, heat capacity by 10%, and thermal conductivity by 20%, and decreased the mass density by 1%. Structural analysis, performed with Raman spectroscopy, indicated that the borosilicate network polymerized with sulfur additions up to 3.0 mass%, presumably due to Na₂O being required to charge compensate the ionic additions, thus becoming unavailable to form non-bridging oxygen in the silicate network. It is postulated that this increased cross-linking of the borosilicate backbone led to a structure with higher dimensionality and average bond energy. This increased the mean free paths and vibration frequency of the phonons, which resulted in the observed increase in thermal properties.     

RB Regulates DNA Double Strand Break Repair Pathway Choice by Mediating CtIP Dependent End Resection

Inactivation of the retinoblastoma tumor suppressor gene (RB1) leads to genome instability, and can be detected in retinoblastoma and other cancers. One damaging effect is causing DNA double strand breaks (DSB), which, however, can be repaired by homologous recombination (HR), classical non-homologous end joining (C-NHEJ), and micro-homology mediated end joining (MMEJ). We aimed to study the mechanistic roles of RB in regulating multiple DSB repair pathways. Here we show that HR and C-NHEJ are decreased, but MMEJ is elevated in RB-depleted cells. After inducing DSB by camptothecin, RB co-localizes with CtIP, which regulates DSB end resection. RB depletion leads to less RPA and native BrdU foci, which implies less end resection. In RB-depleted cells, less CtIP foci, and a lack of phosphorylation on CtIP Thr847, are observed. According to the synthetic lethality principle, based on the altered DSB repair pathway choice, after inducing DSBs by camptothecin, RB depleted cells are more sensitive to co-treatment with camptothecin and MMEJ blocker poly-ADP ribose polymerase 1 (PARP1) inhibitor. We propose a model whereby RB can regulate DSB repair pathway choice by mediating the CtIP dependent DNA end resection. The use of PARP1 inhibitor could potentially improve treatment outcomes for RB-deficient cancers.     

Highly Aligned Centrifugal Spun Polyacrylonitrile Nanofibers Collected and Processed with Automated Tracks

A parallel automated track collector is integrated with a rationally designed centrifugal spinning head to collect aligned polyacrylonitrile (PAN) nanofibers. Centrifugal spinning is an extremely promising nanofiber fabrication technology due to high production rates. However, continuous oriented fiber collection and processing presents challenges. Engineering solutions to these two challenges are explored in this study. A 3D-printed head design, optimized through a computational fluid dynamics simulation approach, is utilized to limit unwanted air currents that disturb deposited nanofibers. An automated track collecting device has pulled deposited nanofibers away from the collecting area. This results in a continuous supply of individual aligned nanofibers as opposed to the densely packed nanofiber mesh ring that is deposited on conventional static post collectors. The automated track collector allows for simple integration of the postdraw processing step that is critical to polymer fiber manufacturing for enhancing macromolecular orientation and mechanical properties. Postdrawing has enhanced the mechanical properties of centrifugal spun PAN nanofibers, which have different crystalline properties compared with conventional PAN microfiber. These technological developments address key limitations of centrifugal spinning that can facilitate high production rate commercial fabrication of highly aligned, high-performance polymer nanofibers.     

Photodegradation of dye pollutants on TiO2 nanoparticles dispersed in silicate under UV–VIS irradiation

A novel catalyst, TiO₂ nanoparticles dispersed in silicate, were used to photodegrade sulforhodamine B (SRB) under UV–VIS irradiation. With good photocatalytic activity and the ability to be readily separated from the reaction system, this novel catalyst exhibits the potential to be effective in the treatment of dye pollutants in aqueous systems.     

Ink-Jet Printing of Binders for Ceramic Components

Layered manufacturing methods for fabricating ceramic components can involve selective deposition of binder using ink-jet printing. Selection of a proper binder plays a critical role in fabricating parts with good surface finish, dimensional accuracy, and high resolution. Several polymeric solution-phase binders were investigated in terms of their physical properties, printing performance, and binder-powder bed interaction. It was observed that the molecular weight should be <15 000 for the binder to be penetrated into dense powder compacts. Binder infiltration kinetics and printed line width were also significantly influenced by powder-bed characteristics, such as surface roughness and pore size, as well as the physical properties of the binder, such as viscosity and surface tension.     

A Functionally Graded Carbide in the Ta–C System

Hard materials used in such abrasive wear applications as cutting tools and wear inserts in drilling tools require high hardness to resist wear, high fracture toughness to withstand mechanical and thermal shock, and high chemical and thermal stability. Such a combination of properties is difficult to achieve in single‐phase materials. Functional grading is an approach that overcomes this limitation by designing and processing a graded microstructure that provides high hardness and chemical resistance at the surface with a tough interior or bulk. While functional grading is a widely used practice in the cemented carbides industry, it has not been demonstrated with “pure” carbides. This article reports the feasibility of designing and processing a graded carbide in the Ta–C binary system. It is shown that a simple carburization treatment of the high‐toughness carbide, ζ‐Ta₄C_3?x, can lead to the formation of the hard carbide phase, γ‐TaC_y, on the surface. The thickness, microstructure (grain size), and composition (C/Ta atomic ratio, y) of the γ‐TaC_y layer can be optimized to obtain both high hardness and high strength for the graded material.     

First Identification of a Putative Sex Pheromone in a Praying Mantid

Praying mantids are models for a wide variety of behavioral, physiological, and ecological studies, and sex pheromones have been assumed to be important components of their biology. However, no mantid pheromone has ever been identified. We collected volatiles emitted by females of the mantid, Sphodromantis lineola, via solid phase microextraction (SPME). Mass spectral analysis revealed the collected volatiles to be a mixture of pentadecanal and tetradecanal. We prepared a synthetic mixture of these compounds, and found that males were both attracted to this mixture and stimulated to exhibit typical precopulatory behavior. We then examined male antennae with scanning electron microscopy, and confirmed the presence of porous antennal sensilla typical of insect pheromone receptors, i.e., that male mantids are equipped with the appropriate morphological apparatus to receive volatile chemical signals. Pheromones, in conjunction with visual and tactile cues, are thus an important feature of the reproductive biology of this, and undoubtedly other species of mantids. In addition to adding a crucial aspect of behavioral biology to our knowledge of this group, identification and synthesis of mantid pheromones may be a first step in attracting and aggregating these generalist predators for use in pest control.     

Development of novel 1,2,3,4-tetrahydroisoquinoline derivatives and closely related compounds as potent and selective dopamine D3 receptor ligands

Based on N-alkylated 1,2,3,4-tetrahydroisoquinoline derivatives, which are structurally related to the partial agonist BP 897, a series of novel, selective dopamine D3 receptor antagonists has been synthesised. Derivatisation included changes in the arylamide moiety and the tetrahydroisoquinoline substructure leading to compounds with markedly improved selectivities and affinities in the low nanomolar concentration range. From the 55 structures presented here, (E)-3-(4-iodophenyl)-N-(4-(1,2,3,4-tetrahydroisoquinolin-2-yl)butyl)acrylamide (51) has high affinity (Ki(hD3)=12 nM) and a 123-fold preference for the D3 receptor relative to the D2 receptor subtype. Its pharmacological profile offers the prospect of a novel radioligand as a tool for various dopamine D3-receptor-related in vitro and in vivo investigations.