Beam test of the CsI(Tl) calorimeter for the BELLE detector at the KEK-B factory

We studied the performance of a prototype electromagnetic calorimeter for the BELLE detector at the KEK proton synchrotron for an energy range of 0.25–3.5 GeV. The prototype consisted of an array of 6 × 5 CsI(Tl) crystals with 30 cm length (16.2 radiation lengths) and about 6 cm × 6 cm cross section. The scintillation light of each CsI(Tl) crystal was read out by two large-area PIN photodiodes and charge-sensitive preamplifiers attached at the rear face of the crystal. We measured the energy and position resolution for electrons and the e/π separation for two sets of matrix configurations: one corresponded to the center and the other to the edge of the barrel calorimeter. The overall performance measured by the test proves that the prototype calorimeter is satisfactory for the use in the BELLE detector.     

Performance evaluation of the Golay code pulse compression technique

The Center for NDE, Iowa State University, has developed a laboratory prototype Golay code pulse compression system and tested it on a variety of materials. The performance of the system was evaluated in terms of signal-to-noise ratio enhancement (SNRE), resolution, and computation speed. The system's error sources also were discussed. The Golay code pulse compression was simulated on a computer and demonstrated the effective noise suppression. In addition, an equivalent pulse of the Golay code (delta-like pulse) was derived theoretically using a simple ultrasonic inspection model, which demonstrated its equivalence on the output correlated signal. Overall, the pulse compression technique extended the detection range for a given peak power and considerably reduced the system'swhite noise, hence providing enhanced signal-to-noise ratios (SNRs). An average of 30 dB improvement in SNR was obtained from highly energy-absorbent materials such as rubber, plastics, corks (insulation materials), and thick composites using the Golay codes of up to 512 bits. However, the technique did not effectively reduce coherent scattering noises from the coarse grain boundaries in cast stainless steels, Inconel weld metal, and material lay-ups in thin composites. Furthermore, it was found that, depending upon the system's hardware capabilities, the overall performance could be degraded considerably.     

Enhancement mode InP MISFET's with sulfide passivation andphoto-CVD grown P3N5 gate insulators

High performance enhancement mode InP MISFET's have been successfully fabricated by using the sulfide passivation for lower interface states and with photo-CVD grown P₃N₅ film used as gate insulator. The MISFET's thus fabricated exhibited exhibited pinch-off behavior with essentially no hysteresis. Furthermore the device showed a superior stability of drain current. Specifically under the gate bias of 2 V for 10⁴ seconds the room temperature drain current was shown to reduce from the initial value merely by 2.9% at the drain voltage of 4 V. The effective electron mobility and extrinsic transconductance are found to be about 2300 cm ²/V·s and 2.7 mS/mm, respectively. The capacitance-voltage characteristics of the sulfide passivated InP MIS diodes show little hysteresis and the minimum density of interface trap states as low as 2.6×10¹⁴/cm² eV has been attained     

Ultra-wideband (from DC to 110 GHz) CPW to CPS transition

A new ultra-wideband, low-loss and small-size coplanar waveguide (CPW) to coplanar strip (CPS) transition which can be used from DC to 110 GHz is presented. The proposed transition connects CPW with CPS by the reformed air-bridge. Two ground planes of CPW are tied at their ends by a line and the centre of the line is connected to the ground strip of CPS by another line. Owing to the symmetry of the proposed structure, the currents of two ground planes of CPW are combined with the same phase and transferred to the ground strip of CPS. With height of 3 μm, the signal line of CPW passes over two connecting lines and is connected to the signal strip of CPS. For the back-to-back transition structure, insertion loss <1 dB and return loss >15 dB are obtained from 0.5 to 110 GHz     

The prospects of non-volatile phase-change RAM

Phase-change read-and-write memory (PRAM) is a promising memory that can solve the problems of conventional memory—scalability, read/write speed, and reliability. We will review the opportunities and technical challenges of PRAM. The most important challenge of PRAM is the reduction of the writing current. Various approaches to reduce the writing current will be reviewed and the prospects of PRAM are discussed.     

Effects of tube rupture modeling and the parameters on the analysis of multiple steam generator tube rupture event progression in APR1400

A multiple steam generator tube rupture (MSGTR) event in APR1400 has been investigated using the best estimate thermal hydraulic system code, MARS1.4. The effects of the parameters such as the number of ruptured tubes, rupture location, affected steam generator on the analysis of the MSGTR event in APR1400 are examined. In particular, tube rupture modeling methods, single tube modeling (STM) and double tube modeling (DTM), are compared. The APR1400 is found to have the capability of allowing more than 30 min to operators for the MSGTR event of five tubes. The effects of rupture location on the MSSV lift time is not significant in the case of STM, but the MSSV lift time for tube-top rupture is found to be 25.3% larger than that for rupture at the hot-leg side tube sheet in the case of DTM. The MSSV lift time for the cases that both steam generators are affected (4C5x, 4C23x) are found to be larger than that of the single steam generator cases (4A5x, 4B5x) due to a bifurcation of the primary leak flow. The discharge coefficient of Cd is found to affect the MSSV lift time only for a smaller value of 0.5. It is found that the most dominant parameter governing the MSSV lift time is the leak flow rate. Whether any modeling method is used, it gives the similar MSSV lift time if the leak flow rate is close, except in the case where both steam generators are affected. Therefore, the system performance and the MSSV lift time of the APR1400 are strongly dependent on the break flow model used in the best estimate system code.     

Capacitor coupled converter (C3) for high power DCconversion

The bang-bang controlled capacitor coupled converter (C³) is described in this paper. Due to the converter's inherent commutating property, the C³ can accommodate thyristors as well as high-power gate turn-off switches, due to zero-current switching transitions. The zero-current switching is achieved at no current stress increase, therefore, the topology is considered appropriate for high-power processing. DC and small signal AC models are derived for the bang-bang controlled C³, a design procedure is proposed, and simulation results are discussed. Finally, oscillograms from a proof of principle prototype circuit are presented     

Customer entrepreneurship on digital platforms: Challenges and solutions for platform business models

Drawing on the mixed methods of qualitative research and agent‐based simulation, this study examines: (a) how end‐users use digital platforms to become customer–entrepreneurs undertaking commercial activities on platforms; and (b) how platform providers can convert this customer entrepreneurship into a revenue stream. Considering that end‐users have traditionally been defined as passive and uncharged actors in platform business models, an in‐depth understanding of their commercial activities and the viable revenue model to monetize this emerging customer practice is warranted. Our qualitative study reveals that customer–entrepreneurs make substantial use of platform offerings to advertise their products; communicate with end‐consumers; and accept payments. These commercial activities are largely exercised for free on platforms, even though they could otherwise serve as a source of revenue. On this point, our simulation results identify two pricing models achieving the generation of nearly identical revenues over time. First, platform providers may charge both advertising and transaction fees, which maximize the survival of professional customer–entrepreneurs. Second, platform businesses may levy advertising fees only, which maximizes the survival of informal customer–entrepreneurs operating on a micro‐scale and part‐time basis. This study offers theoretical, methodological, and managerial implications for platform studies.     

Signal tracking method of GNSS receivers for spinning vehicles

A signal tracking method of GNSS receivers for spinning vehicles is proposed in order to eliminate the influence of spinning to the GNSS signal of a vehicle. In the proposed method, a rotation tracking loop is added into the carrier tracking loop of a conventional GNSS receiver. The proposed method was verified through computer simulations and an experiment for live GPS signals. The results show that the proposed method gives an accurate tracking performance.