用于重离子核反应实验测量的纵向电场气体电离室

本文报道了一种新型的大动态范围，多叠层探测器系统组件之一的纵向电场气体电离室的构造，性能和在中能得离子核反应实验中的应用。     

高质量的一级光栅1．55μmDFB激光器

本文详细叙述了ＤＦＢ激光器的设计要点和新的工艺。采用一级全息光栅和二步液相外延法批量研制出高稳定单纵模工作的１．５５μｍ分布反馈激光器（ＤＦＢ—ＬＤ）。外延片成品率＞４０％。器件特性：２５℃时阈值电流２０ｍＡ，单面光功率＞１０ｍｗ，主边模抑制比ＳＭＳＲ达４３ｄＢ（λ／４相移光栅），谱线宽度△ν－２０ｄＢ＝０．３ｎｍ，调制速率＞１．８ＧＨｚ。可靠性测试显示：高温监测光谱稳定，２５°Ｃ时阈值退化率△Ｉｔｈ／ｔ＜０．３ｍＡ／ｋｈ，对应器件预估寿命将超过１０万ｈ。     

An error and sensitivity analysis of the atmospheric- andsoil-correcting variants of the NDVI for the MODIS-EOS

Several soil- and atmospheric-correcting variants of the normalized difference vegetation index (NDVI) have been proposed to improve the accuracy in estimating biophysical plant parameters. In this study, a sensitivity analysis, utilizing simulated model data, was conducted on the NDVI and variants by analyzing the atmospheric- and soil-perturbed responses as a continuous function of leaf area index. Percent relative error and vegetation equivalent “noise” (VEN) were calculated for soil and atmospheric influences, separately and combined. The NDVI variants included the soil-adjusted vegetation index (SAVI), the atmospherically resistant vegetation index (ARVI), the soil-adjusted and atmospherically resistant vegetation index (SARVI), the modified SAVI (MSAVI), and modified SARVI (MSARVI). Soil and atmospheric error were of similar magnitudes, but varied with the vegetation index. All new variants outperformed the NDVI. The atmospherically resistant versions minimized atmospheric noise, but enhanced soil noise, while the soil adjusted variants minimized soil noise, but remained sensitive to the atmosphere. The SARVI, which had both a soil and atmosphere calibration term, performed the best with a relative error of 10 percent and VEN of ±0.33 LAI. By contrast, the NDM had a relative error of 20 percent and VEN of ±0.97 LAI     

Suppression of boron penetration in p+ polysilicon gateP-MOSFETs using low-temperature gate-oxide N2O anneal

It has been reported that high-temperature (~1100°C) N₂ O-annealed oxide can block boron penetration from poly-Si gates to the silicon substrate. However, this high-temperature step may be inappropriate for the low thermal budgets required of deep-submicron ULSI MOSFETs. Low-temperature (900~950°C) N₂O-annealed gate oxide is also a good barrier to boron penetration. For the first time, the change in channel doping profile due to compensation of arsenic and boron ionized impurities was resolved using MOS C-V measurement techniques. It was found that the higher the nitrogen concentration incorporated at Si/SiO₂ interface, the more effective is the suppression of boron penetration. The experimental results also suggest that, for 60~110 Å gate oxides, a certain amount of nitrogen (~2.2%) incorporated near the Si/SiO₂ interface is essential to effectively prevent boron diffusing into the underlying silicon substrate     

钒冶炼焙烧添加剂选择研究

对小型钒冶炼厂焙烧工艺所用添加剂进行改进的可能性进行了探讨，研究了几种常用添加剂的焙烧条件，分析比较了其性能，提出用ＮａＣｌ－Ｎａ２ＣＯ３作焙烧添加剂替代ＮａＣｌ可大幅度减少大气污染，提高冶钒转化率；且不改变工艺流程，无需设备投资，具有较好的经济效益和环境效益。     

Preparation and optical properties of CdxHg1-xTe doped silica glass

In this paper, the Cd_xHg_1-xTe (x=1-0.7) doped silica glass was prepared through two step sol-gel process and in-situ growth technique from tetraethoxysilane (TEOS), cadmium acetate, mercury acetate and telluric acid. The influence of various factors on the glass was studied. The structure of the microcrystals was investigated by XRD. The absorption and transmittance spectrum of the composite showed that the shift of absorption edge was in conformity with the quantum size effect. The third-order nonlinear optical susceptibility χ⁽³⁾ was measured by the degenerate four wave mixing (DFWM). The values of χ⁽³⁾ was in the range of 10^-11-10^-12 MO esu at wavelength of 1.06 μm.     

土钉支护结构水平位移安全监控模型研究

国内现行规范、标准是以极限变形值作为土钉支护结构水平位移安全监测报警值 ,但没有反映工程进度影响 ,不便指导工程实践。提出“过程控制”概念 ,以反正切函数为基本形式 ,基于历史经验建立“安全时程曲线”控制模型 ,要求施工过程中实测水平位移始终处在“安全时程曲线”之下 ,以确保最终变形在某一适当的阈值之内 ,已有实测结果可以为施工方案调整提供依据。通过实际案例 ,检验模型的可行性 ,表明过程控制模型较极限变形策略更具可操作性     

Application of asymptotic waveform evaluation to eigenmode expansion method for analysis of simultaneous switching noise in printed circuit boards (PCBs)

In this paper, the asymptotic waveform evaluation (AWE) technique is first applied to the conventional eigenmode expansion method for characterizing a power/ground (P/G) plane pair and analyzing the simultaneous switching noise on such plane pairs for printed circuit boards or multichip modules. The application of AWE avoids a large number of iterations in computing the impedance frequency response of a P/G plane pair structure and greatly reduces the computation time. Meanwhile, to obtain an accurate solution in an entire frequency range, we employ the complex frequency hopping technique which can help select multiple expansion points. In addition, the proposed approach can also be used to characterize the P/G plane pair structures with irregular shapes. Three examples demonstrate its high efficiency and good accuracy.