Analysis of an adaptive rate convolutionally coded multicarrierDS/CDMA system

The analysis of an adaptive rate convolutionally coded multicarrier direct sequence code division multiple-access (DS/CDMA) system is considered. In order to accommodate a number of coding rates easily and make the encoder and decoder structure simple, we use the rate-compatible punctured convolutional (RCPC) code. We obtain data throughputs at several coding rates, and choose the coding rate that has the highest data throughput in the signal-to-interference and noise ratio (SINR) sense. To achieve maximum data throughput, a rate adaptive system is proposed based on the channel state information (the SINR estimate). The SINR estimate is obtained by the soft decision Viterbi decoding metric. We show that the proposed rate adaptive convolutionally coded multicarrier DS/CDMA system can enhance the spectral efficiency and provide frequency diversity     

An efficient frequency offset estimator for OFDM systems and itsperformance characteristics

In this paper, we propose a new frequency synchronization algorithm for orthogonal frequency division multiplexing (OFDM) systems requiring only one training symbol, based on a conventional method which requires two training symbols. While the timing synchronization is obtained by using the conventional method, the carrier frequency offset is efficiently estimated by the proposed method. It is shown that the proposed method not only reduces the number of the training symbols but also possesses better performance than the conventional method without increase in complexity     

Wide‐Band Fine‐Resolution DCO with an Active Inductor and Three‐Step Coarse Tuning Loop

This paper presents a wide‐band fine‐resolution digitally controlled oscillator (DCO) with an active inductor using an automatic three‐step coarse and gain tuning loop. To control the frequency of the DCO, the transconductance of the active inductor is tuned digitally. To cover the wide tuning range, a three‐step coarse tuning scheme is used. In addition, the DCO gain needs to be calibrated digitally to compensate for gain variations. The DCO tuning range is 58% at 2.4 GHz, and the power consumption is 6.6 mW from a 1.2 V supply voltage. An effective frequency resolution is 0.14 kHz. The phase noise of the DCO output at 2.4 GHz is –120.67 dBc/Hz at 1 MHz offset.     

Advanced Concentration Gradient Cathode Material with Two‐Slope for High‐Energy and Safe Lithium Batteries

Li[Ni_0.65Co_0.13Mn_0.22]O₂ cathode with two‐sloped full concentration gradient (TSFCG), maximizing the Ni content in the inner part of the particle and the Mn content near the particle surface, is synthesized via a specially designed batch‐type reactor. The cathode delivers a discharge capacity of 200 mAh g^?1 (4.3 V cutoff) with excellent capacity retention of 88% after 1500 cycles in a full‐cell configuration. Overall electrochemical performance of the TSFCG cathode is benchmarked against conventional cathode (CC) with same composition and commercially available Li[Ni_0.8Co_0.15Al_0.05]O₂ (NCA). The TSFCG cathode exhibits the best cycling stability, rate capability, and thermal stability of the three electrodes. Transmission electron microscopy analysis of the cycled TSFCG, CC, and NCA cathodes shows that the TSFCG electrode maintains both its mechanical and structural integrity whereas the NCA electrode nearly pulverizes due to the strain during cycling.     

A management architecture for client‐defined cloud storage services

Cloud service providers offer virtual resources to users, who then pay for as much as they use. High‐speed networks help to overcome the limitation of geographical distances between clients and cloud servers, which encourage users to adopt cloud storage services for data backup and sharing. However, users use only a few cloud storage services because of the complexity of managing multiple accounts and distributing data to store. In this paper, we propose the client‐defined management architecture (CLIMA) that redefines a storage service by coordinating multiple cloud storage services from clients. We address practical issues of coordinating multiple cloud service providers using a client‐based approach. We implement a prototype as a realization of CLIMA, which achieves both reliability and privacy protection using erasure code and higher performance by optimally scheduling data transmission. We use our prototype to evaluate the benefits of CLIMA on commercial cloud storage service providers. Finally, CLIMA empowers clients to increase the manageability and flexibility of cloud storage services. Copyright © 2015 John Wiley & Sons, Ltd.     

Passive alignment method of polymer PLC devices by using a hot embossing technique

A novel fabrication process using a hot embossing technique has been developed for micromechanical passive alignment of polymer planar lightwave circuit (PLC) devices. With only one step of embossing, single-mode waveguide straight channels and micropedestals for passive aligning are simultaneously defined on a polymer thin film with an accuracy of /spl plusmn/0.5 /spl mu/m. This process reduces the steps for fabricating alignment structures. A fabricated polymer PLC chip and fibers are combined on a v-grooved silicon optical bench (SiOB) in a flip-chip manner. The process provides a coupling loss as low as 0.67 dB per coupling face and a cost-effective packaging solution for various polymer PLC devices.     

Simultaneous Measurements of Dispersion Parameter and Fiber Length Using the Self-Seeding Laser Oscillation of a Fabry–PÉrot Laser Diode

A simultaneous measurement technique of the dispersion parameter and the length of an optical fiber has been demonstrated by using the self-seeding laser oscillation of a Fabry-Perot laser diode. We measured the dispersion parameter and the length of an optical fiber from the modulation frequency changes required to induce single-mode laser oscillations through an optical closed-loop path. The dispersion and fiber length measurements were within 1.5% and 0.2%, respectively, of the values measured by commercial instruments.     

Measurement-Based Achievable Throughput Estimation in IEEE 802.11a WLANs

Knowledge of dynamically changing achievable throughput is important in the design of an adaptive QoS-provisioning system over WLANs. In this letter, we introduce a novel measurement-based throughput estimation scheme and its practical realization for IEEE 802.11a WLAN environment. By utilizing traffic statistics measurements at the wireless AP (access point) in a timely manner, the proposed scheme estimates idle (i.e., remaining) channel time and converts it into available min/max throughput guidelines. Prototype realization in a Linux-based testbed verifies that the proposed scheme can estimate the available throughput with precision.     

A Temperature‐Controllable Microelectrode and Its Application to Protein Immobilization

This letter presents a smart integrated microfluidic device which can be applied to actively immobilize proteins on demand. The active component in the device is a temperature‐controllable microelectrode array with a smart polymer film, poly(N‐isopropylacrylamide) (PNIPAAm) which can be thermally switched between hydrophilic and hydrophobic states. It is integrated into a micro hot diaphragm having an integrated micro heater and temperature sensors on a 2‐micrometer‐thick silicon oxide/silicon nitride/silicon oxide (O/N/O) template. Only 36 mW is required to heat the large template area of 2 mm×16 mm to 40°C within 1 second. To relay the stimulus‐response activity to the microelectrode surface, the interface is modified with a smart polymer. For a model biomolecular affinity test, an anti‐6‐(2, 4‐dinitrophenyl) aminohexanoic acid (DNP) antibody protein immobilization on the microelectrodes is demonstrated by fluorescence patterns.     

Reconstruction of conductivity and current density images using only one component of magnetic field measurements

Magnetic resonance current density imaging (MRCDI) is to provide current density images of a subject using a magnetic resonance imaging (MRI) scanner with a current injection apparatus. The injection current generates a magnetic field that we can measure from MR phase images. We obtain internal current density images from the measured magnetic flux densities via Ampere's law. However, we must rotate the subject to acquire all of the three components of the induced magnetic flux density. This subject rotation is impractical in clinical MRI scanners when the subject is a human body. In this paper, we propose a way to eliminate the requirement of subject rotation by careful mathematical analysis of the MRCDI problem. In our new MRCDI technique, we need to measure only one component of the induced magnetic flux density and reconstruct both cross-sectional conductivity and current density images without any subject rotation.