聚甲亚胺改性尼龙6复合材料的等温结晶动力学

采用差示扫描量热法（DSC）对聚甲亚胺（PAM）/尼龙6复合材料等温结晶过程进行了研究。结果表明，PAM的加入使得基体的结晶速率增大，尤其是当含量为5%时，半结晶期明显减少。研究还发现，该体系的等温结晶过程完全可以用Avrami方程来描述，各试样的Avrami指数均在2-3之间，表明Avrami指数，球晶生长方式基本不受聚甲亚胺加入的影响。基体中原位形成的聚甲胺微纤起到了诱导结晶的作用，使得基体的结晶速率加快，但随着微纤含量的增加，由于分散性能变差而使得诱导结晶的能力减弱，表现为结晶速率又有所降低。     

高分子表面活性剂对超声辐照下苯乙烯乳液聚合的影响

在超声辐照引发苯乙烯乳液聚合中加入一种新型的以羧甲基纤维素为基础的高分子表面活性剂(CMC—A9)，讨论了高分子表面活性剂对反应动力学的影响。实验表明，超声辐照下初级自由基并非由通常认为的高分子表面活性剂产生，而是十二烷基硫酸钠在超声辐照下断裂，产生自由基。通过对反应动力学的研究，发现超声辐照下乳液聚合机理不同于常规乳液聚合，聚合反应过程只有两个阶段，即加速期和减速期，不存在恒速期。加入CMC—A9高分子表面活性剂，可以在较短的时间内和较低的超声功率下达到较高的单体转化率。     

Feasibility analysis of phonon lasers

We identify the main reason impeding coherent generation of phonons in solid state - the inherently high density of phonon states. Based on the results of our analysis we formulate a set of conditions that may make phonon lasing practical and point out the most promising mechanism of phonon lasing: LO/spl rarr/LA+TO in InP. We then develop a complete set of phonon laser equations and evaluate the threshold, output power and efficiency of phonon lasers based on InP MESFET. We show that one can obtain high-power 1.26-THz coherent phonon emission with pump power as small as a few milliwatts and up to 5% slope efficiency. Potential applications are also discussed.     

TBM掘进隧洞回填固结灌浆施工的探讨

豆砾石回填灌浆和固结灌浆在引黄工程南干线长达90kmTBM施工中得到成功的应用。文中介绍了引黄工程南干线4^#-7^#隧洞豆砾石回填灌浆、特殊地质洞段的固结灌浆的灌浆设备、材料、浆液配比、压力、工艺等诸方面的现场施工情况。     

应用AR模型的IMU误差系数漂移预测研究

将影响IMU误差系数漂移并难于分离的多种因素综合为一种因素，假定IMU误差系数的漂移由一特定系统所引起，从而采用时间序列建模方法进行IMU误差系数漂移的预测。该方法具有消除各因素具体分析中的不确定性并减少其工作员的优点。文中描述了其原理，对某惯组的33个误差系数进行了时间序列建模与预测并得到有效的结果。最后还阐述了存在的问题及其解决方法。     

一种单片机控制的指令转换器的设计

采用89C51单片机，串口扩展芯片8251、中断扩展芯片8259等器件设计了一种指令格式转换器。     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

山区长输气管线的曲线测设

该文介绍了在山区长输气管线测量中 ,管线的折点桩之间大部分不通视且部分点上空有障碍物 ,采用GPS不能施测坐标时 ,结合山区的自然地理条件 ,采用全站仪间接施测折点水平角 ,极坐标法测设曲线以及跨越障碍物测设曲线的内容和方法 ,可在一定精度要求下应用     

自动交换光网络的标准化现状

国际上许多标准化组织都在对自动交换光网络的相关技术和标准规范进行研究。本文介绍了ITU－T、IETF和OIF等几个主要的标准化组织在自动交换光网络标准方面的进展情况。