Microwave Dielectric Properties of (1−x)(Na1/2Nd1/2)TiO3−xLa(Mg1/2Ti1/2)O3 via Ordering and Far IR Reflectivity Spectra

Microwave dielectric properties of (1− x )(Na_1/2Nd_1/2)TiO₃(NNT)− x La(Mg_1/2Ti_1/2)O₃(LMT) system have been investigated with focus on structural ordering and far IR reflectivity spectra. A single perovskite phase was found to exist with various superlattice reflections over the entire compositional range. 1:1 ordering observed in the (111) reflection of X-ray diffraction patterns was found to progress significantly in the specimens above x =0.8. The ordering characteristics that presumably related to B-site Mg/Ti ordering were assumed to affect favorably the quality factor at microwave frequencies. The increase of the quality factor also could be explained in terms of the decrease of lattice anharmonicity with LMT by analysis of far IR reflectivity spectra. As expected from the values of pure NNT and LMT, the dielectric constant and the temperature coefficient of frequency tended to gradually decrease with increasing LMT content.     

Effect of Antimony Addition on Electrical and Optical Properties of Tin Oxide Film

Antimony-doped tin oxide films were prepared on Corning glass substrate by chemical vapor deposition from a gas mixture of SnCl₄–SbCl₅–H₂O. The electrical conductivity and optical transmission of tin oxide films were studied with antimony doping. The film conductivity increased largely without losing optical transparency with a small addition of antimony. The increase of the conductivity was attributed mainly to more electrons donated by pentavalent Sb ions in the SnO₂ lattice. Large additions of antimony, however, diminished the conductivity, optical transparency, and crystallinity of the film. The diminution was found to be caused by fine Sb₂O₅ phases codeposited with SnO₂.     

An Experimental Study of Fatigue Strength for Adhesively Bonded Tubular Single Lap Joints

In this paper, manufacturing technology of the tubular single lap adhesive joint was studied to obtain reliable and optimal joint quality. In addition, a surface preparation method and a bonding process for the joint were devised. The effect of the adhesive thickness and the adherend roughness on the fatigue strength of the joint was experimentally investigated. From experiments, it has been found that the fatigue strength of the joint increased as the adhesive thickness decreased and the optimal arithmetic surface roughness of the adherends was about 2 μm.     

Strain-Induced Deformation in Magnesia–Alumina Layered Composites

Ceramic beams are induced in situ to form complex shapes at elevated temperature without the application of an external stress. This process has been demonstrated for thin alumina substrates coated with a layer of magnesia. The internal strain causing the substrates to deform at elevated temperature arises as a consequence of strain mismatch accompanying the penetration of the coating into the substrate. The magnitude of the deformation depends on the amount of coating applied, on the thickness of the substrate, on the density of the substrate, and on the temperature. During exposure of the beams to elevated temperature, the magnesia coating reacts with the alumina substrate to form the spinel phase; the resulting volume change accompanying the phase transformation is likely the predominant driving force for deformation.     

Synthesis and properties of acrylonitrile-CR-methyl methacrylate graft copolymer

Graft copolymerization of acrylonitrile (AN) and methyl methacrylate (MMA) onto polychloroprene (CR) was carried out using benzoyl peroxide as initiator. The effects of mole ratio of AN to MMA, reaction temperature, reaction time, solvent, and initiator concentration on the graft copolymerization were examined. It was found that the thermal stability and weatherability of the AN—CR—MMA graft copolymer (ACM) were considerably better than those of CR.     

The effects of Ni and Li doping on the performance of lithium manganese oxide material for lithium secondary batteries

Layered Li_0.7[M_1/6Mn_5/6]O₂ (M=Li, Ni) was synthesized using a sol-gel method. P2-Na_0.7[M_1/6Mn_5/6]O₂ precursor was first synthesized by a sol-gel method, and then O2-Li_0.7[M_1/6Mn_5/6]O₂ was prepared by an ion exchange of Li for Na in P2-Na_0.7[M_1/6Mn_5/6]O₂ precursor. From charge/discharge curves, it was seen that Li_0.7[Li_1/6Mn_5/6]O₂ has two plateaus similar to those observed from a spinel structure, but Li_0.7[Ni_1/6Mn_5/6]O₂ holds a single plateau as observed from a typical layered structure. It was considered that Li_0.7[Li_1/6Mn_5/6]O₂ undergoes a phase transformation from layered to spinel structure during the charge/discharge cycle, but Li_0.7[Ni_1/6Mn_5/6]O₂ maintains O2-layered structure after the cycles. Li_0.7[Ni_1/6Mn_5/6]O₂ was higher in discharge capacity and retention rate than Li_0.7[Li_1/6Mn_5/6]O₂.     

High catalytic activity of PdOx/MnO2 for CO oxidation and importance of oxidation state of Mn

PdO_x/MnO₂ has been examined as a catalyst for CO oxidation using a conventional flow reactor at reaction temperatures between 50 and 150°C. In the reaction conditions of GHSV (gashourlyspacevelocity) of 1.22 × 10⁵/h and CO concentration of 2000 ppm, PdO_x/MnO₂ showed higher catalytic activity compared with PdO_x/Mn₂O₃, which had been previously reported as an effective catalyst due to the cooperative action of Pd and Mn₂O₃ for this reaction. The reason for higher activity of PdO_x/MnO₂ than PdO_x/Mn₂O₃ has been investigated using TPR (temperatureprogrammed reduction) and XPS studies. TPR showed that PdO_x/MnO₂ could be reduced by CO at much lower temperature than PdO_x/Mn₂O₃. During the experiment of reduction and oxidation, XPS showed that the valence of Mn in the PdO_x/MnO₂ was between 4+ and 3+, which is higher than that of Mn in the PdO_x/Mn₂O₃ catalyst of which the valence has been reported to be between 3+ and 2+. It is known that in this catalyst system the support supplies oxygen onto Pd, where the oxidation occurs with adsorbed CO, and the ability of the support to provide oxygen improves the performance of the catalyst. Therefore, it was concluded that the readiness of MnO₂ to be reduced with maintaining a higher oxidation state showed higher CO oxidation activity than Mn₂O₃ as support for PdO_x.     

Absorption of NO x in packed column (I)

A mathematical model for an absorption of nitrogen oxides into water in packed column was developed based on the mass-transfer coefficient in packed column and the chemical reaction accompanying NO _x absorption produces HNO₃ and HNO₂ in the liquid phase. The subsequent dissociation of HNO₂ in the liquid-phase results in the formation of HNO₃ and NO gas, and then this NO gas follows to be oxidized by O₂ in air. The important factors influenced on the absorption of NO _x are the oxidation state of NO gas and the partial pressure of nitrogen oxides in the gas. The efficiency of NO _x absorption increases with the increase of the partial pressure of NO _x . The most critical value for using the model is the constant of .The selection of 11×10⁻⁴kg·mol/atm·m²·sec for resonable for this model.     

Measurement of minimum angle of resolution (MAR) in the stereoscopic display using the optotype of stereoscopic stimuli

In stereoscopic images, the crossing point of the viewing directions of the two eyes determines the perceived depth. Assuming that accommodation is affected by the positions of the crossing point, the effect of crossing point on minimum angle of resolution (MAR) was investigated. For 40 participants, MAR was measured by two‐alternative forced choice where Snellen optotype E of up and down directions were used as two kinds of stimuli. As the crossing point of the viewing direction of the left and right eyes moves farther from the sample display, the ability to identify the direction of letter E decreases at the optotype of the same line thickness. The change of MAR shows linear trends with respect to the optical power change that are the reciprocal of the distance from the participant to the crossing points located out of screen and on screen.     

Reactivity,chemical structure,and molecular mobility of urea–formaldehyde adhesives synthesized under different conditions using FTIR and solid‐state 13C CP/MAS NMR spectroscopy

This study was conducted to investigate the effects of reaction pH condition and hardener type on the reactivity, chemical structure, and molecular mobility of urea–formaldehyde (UF) resins. Three different reaction pH conditions, such as alkaline (7.5), weak acid (4.5), and strong acid (1.0), were used to synthesize UF resins, which were cured by adding four different hardeners (ammonium chloride, ammonium sulfate, ammonium citrate, and zinc nitrate) to measure gel time as the reactivity. FTIR and ¹³C‐NMR spectroscopies were used to study the chemical structure of the resin prepared under three different reaction pH conditions. The gel time of UF resins decreased with an increase in the amount of ammonium chloride, ammonium sulfate, and ammonium citrate added in the resins, whereas the gel time increased when zinc nitrate was added. Both FTIR and ¹³C‐NMR spectroscopies showed that the strong reaction pH condition produced uronic structures in UF resin, whereas both alkaline and weak‐acid conditions produced quite similar chemical species in the resins. The proton rotating‐frame spin–lattice relaxation time (T_1ρH) decreased with a decrease in the reaction pH of UF resin. This result indicates that the molecular mobility of UF resin increases with a decrease in the reaction pH used during its synthesis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2677–2687, 2003